TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)
QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.
Flash instruction:
Use "factory" image directly in vendor GUI.
Recovery method:
1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server.
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset
This commit is based on GitHub PR#1112
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/397/198 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 2x LED (green and orange in the same package), 2x button
- UART: TP5(TX) and TP4(RX) test points on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.
Signed-off-by: Federico Cappon <dududede371@gmail.com>
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)
To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1
Signed-off-by: Mathias Kresin <dev@kresin.me>
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*
* Serial console is disabled in OEM non-beta firmwares and corresponding
GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
production (non-beta) U-Boot and firmware.
Currently not working:
1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
by some U-Boot versions.
Flash instruction under vendor GUI:
1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.
FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):
1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
turns on.
Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):
1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.
Hardware Specification (v1.0 EU):
- SoC: QCA9531
- Flash: Winbond W25Q64FV (8MiB)
- RAM: EtronTech EM6AB160TSE-5G (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 2NIC (3x100M + 1x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 12V 1A
Signed-off-by: Filip Moc <lede@moc6.cz>
This adds support for Aerohive AP-121 access point.
Specification:
- SoC: Atheros AR9344-BC2A at 560MHz
- WiFi 1: 2.4GHz Atheros AR9340? - SoC
- WiFi 2: 5.0GHz Atheros AR9382-AL1A
- Memory: 128MB from 2x Nanya NT5TU32M16DG-AC
- SPI: 1MB Macronix MX25L8006E
- NAND: 128MB Hynix H27U1G8F2BTR-BC
- Ethernet: Atheros AR8035-A
- USB: 1x 2.0
- TPM: Atmel SC3204
Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, download and flash LEDE factory image over tftp:
dhcp;
setenv serverip tftp-server-ip;
tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin;
nand erase 0x800000 0x800000;
nand write 0x81000000 0x800000 0x800000;
reset;
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[minor text changes in commit subject and description, fixed
alphabetical order in etc/diag.sh, use only model name in lib/ar71xx.sh,
fixed code style issues in mach-hiveap-121.c, ubinized factory image]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan
This commit adds basic support for Rambutan development kit
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header
Flash instructions:
Stock firmware is OpenWrt, so use:
sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar
or upgarde from GUI (don't save config)
Use factory image to flash from U-Boot:
tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi
nand erase.part ubi
nand write 80060000 ubi ${filesize}
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[split support in uboot-envtools package into a separate commit,
fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Specification:
- SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc)
- RAM: 128 MiB
- Storage: 16MB NOR flash
- Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO
- Ethernet: 2x1G
Tested and working:
- ethernet / switch / lan / wan
- 2.4GHz SoC wifi
- PCIe
- leds
- buzzer
Ramload:
- tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin
- bootm 0x84000000
Install:
- tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin
- erase 0x9f030000 +$filesize
- erase 0x9f680000 +1
- cp.b $fileaddr 0x9f030000 $filesize
Erasing 0x9f680000 is required because uboot defines
"bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot
the higher address. I think the 16 mb flash are intended to be used as
8+8mb for a fallback image. In my hardware only the lower address has a
bootable image. But to make sure future hardware will boot lede too, I
erase one block, so uboot will skip this address.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also
labeled as R602F, R602, etc.) is a simple N300 router with 5-port
10/100 Mbps switch, non-detachable antennas and USB.
CPE505 is an outdoor CPE with PoE support and detachable antennas.
Both devices are based on Qualcomm/Atheros QCA9531 v2.
Common specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- UART (J2) header on PCB
R602N specification:
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm
- 2x external, non-detachable antennas
- 7x LED, 1x button
CPE505N specification:
- 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V)
- 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm
- 2x external, detachable antennas (RP-SMA connectors)
- 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button
Flash instructions:
It seems that there are many different versions of the firmware which
these devices are shipped with. The generic/standard one is based on
some modified OpenWrt and LEDE firmware can be flashed directly from
vendor's webgui or with sysupgrade (root password is "admin123").
Before flashing, make sure (use "fw_printenv") that the kernel load
address in your device is set to "0x9f050000" (bootcmd variable is
"bootm 0x9f050000"). If your device uses different load address, you
should first change it, under vendor's firmware, with command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
Where OLD_ADDRESS is previous kernel load address (in CPE505 version
I got access to, it was "0x9fe80000"). This will allow you to use
both the vendor's and LEDE firmware.
If version of your device contains empty U-Boot environment (you will
get information about this after issuing "fw_printenv"), you should
use U-Boot, serial line access and TFTP to perform firmware upgrade:
1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
5. saveenv && reset
These devices contain also web recovery mode inside U-Boot. It can be
started with pressing the reset button for around 3 seconds just after
the device powerup. Web recovery panel is available on "192.168.10.9"
and to be able to use it, IP on your PC must be set to "192.168.10.10".
Make sure to change kernel load address before using recovery mode or
the U-Boot will not be able to load LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Lima is a module for the (IoE) internet of everything applications,
based on Qualcomm/Atheros QCA4531.
Specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- USB 2.0 Host
- PCIe
- UART for serial console
- 14x GPIO
Flash instruction:
1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin
and rename it to 8dev_recovery.bin
2. Binary file copy to USB stick and plug into slot USB
3. Press S2 (reset) button
4. Press and hold the S1 button by 5 seconds
5. Wait ~40 seconds to complete recovery
Tested on:
- Lima development kit
Signed-off-by: Karol Dudek <karoiz@sli.pl>
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.
Available FLASH space, with LEDE trunk, is only 240 KB.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB
TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")
Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.
The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)
The result factory image is flashable from the stock web ui.
Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Kernel part of support for the PowerCloud Systems CR5000. The
CR5000 is a dual-band 802.11n wireless router with 8MB flash,
64 MB RAM, (unused in stock firmware) USB 2.0 port, and five
port gigabit ethernet switch. The CR5000 was sold as hardware for
the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47940
Kernel part of support for PowerCloud CR3000. The CR3000 is
a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM,
a four port fast ethernet switch, and a fast ethernet wan port which
was sold by PowerCloud Systems as hardware for the Skydog
cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47939
Kernel part of support for PowerCloud CAP324 Cloud AP.
The CAP324 Cloud AP was a device sold by PowerCloud Systems as hardware for
the CloudCommand service for 'cloud' based managment of large numbers
access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a power adaptor.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47938
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40499
Add new subtarget nand with UBI/UBIFS including GLUEBI and squashfs.
This target will be used for NAND based router which make use of
UBI (and maybe UBIFS later on) in order to provide proper NAND
support.
Signed-off-by: Stefan Agner <stefan@agner.ch>
[juhosg:
- tweak target.mk:
change BOARDNAME variable,
improve Target/Description,
remove targz and ubifs from FEATURES and add broken flag,
- optimize kernel configuration:
disable ubifs, it is not used yet,
disable unused MTD options,
disable SPI support
disable unused network drivers,
tune kernel command line,
- remove image/ubinize.cfg, it will be in a follow-up patch
- move profile modifications into a separate patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38646
It is for Mikrotik devices only, rename the subtarget
to reflect that. Also fix the wget2nand script to use
the new image names.
Based on the patch by Stefan Agner:
http://patchwork.openwrt.org/patch/4123/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38509
* add a new SPI controller driver
* add SPI driver for the CPLD chip
* convert the NAND driver
* enable the mikroSD slot
* enable more LEDs
SVN-Revision: 22863
Henryk Heisig