Older git versions seem output the original argument to stdout if there
is no upstream, presumably because they try to do things with it
internally. This can be prevented by passing --verify to it, which
should be safe on newer git versions.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
-fno-plt and musl-libc patches already get upstream, then dropped
in GCC 6. Other patches are almost identical compared to GCC 5.4.
Compile and run tested on ar71xx/Qihoo C301 and
mvebu/Linksys WRT1900ac v1
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanups/fixes]
Use ./patches and ./patches-arc instead of version dependent patches.
We should have only one main supported version (along with the special
case for arc).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
-march forces the compiler to generate generic code, whereas -mcpu
allows it to target the specific CPU variant and use instructions that
the generic architecture may not have
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use kernel config as input instead of -march CFLAGS.
With this change, -march can be dropped and replaced with more specific
optimization flags for better code generation.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This lets one use the CT ath10k driver instead of the built-in
ath10k driver from the upstream kernel (or backports).
This should be a drop-in replacement, as well as enabling
better CT firmware support.
Signed-off-by: Ben Greear <greearb@candelatech.com>
We call all commands normally, with standard echoing. It's useful for
debugging with V=s. Don't make lzma compression an exception, it's a bit
confusing this way.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
The removed patch is already integrated in upstream musl.
Add one additional patch which fixes a regression on mips.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- avoid using tools/include/endian.h on OS X to fix compilation.
- remove unneeded Host/Compile definition.
- refresh patches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers
Default configuration:
- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space
Flash instruction (do it under U-Boot, using RS232):
1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers
Default configuration:
- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Instead of assuming master is the current branch and origin the right
upstream, try to get both dynamically. If the current branch is not
tracking any upstream, use the origin of the master branch.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Felix Fietkau