This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.
This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.
Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37977
- change patch numbers to group the related stuff together,
- add mtd prefix where it is missing,
- use hyphens in the patch names
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37974
Most of the Linksys devices without an own GPIO configuration where
detected as WRT54G. On one board this made OpenWrt to boot into
failsafe every time, because one GPIO configurated as button was not a
button.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37970
This patch adds support for building firmware images for the
TP-Link TL-MR3040 v2. Tested and working on v2.1 hardware.
Signed-off-by: Mads Hansen <d@taba.se>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37964
I checked the GPL code drop from D-Link and tried to get the wireless
and LAN switch LEDs to light up. I found some references in
AthSDK/www/DIR-825_C1/bsp.h as well as
AthSDK/www/DIR-825_C1/rootfs/etc/sysconfig/S2gpio.sh, but in the end I
only got the led for 2.4GHz to work. Anyway, here's the patch.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37963
- fixes buffer corruption with JSON-RPC list calls
- change JSON-RPC protocol to include the session ID into the call
attributes instead of passing it via the URL
- forcibly pass effective session ID as "ubus_rpc_session" attribute
to called procedures
- change ubus acl checking to conform with new ubus session namespace
SVN-Revision: 37962
- recalculate session ACLs on reload
- support negative access group expressions in /etc/config/rpcd
- prevent destryoing the default session
- use "ubus_rpc_session" attribute as session identifier to enforce JSON-RPC proxy security
SVN-Revision: 37961
The imx sata module has only been backported to imx6 target. This change will
fix buildbot errors due to missing patches in other targets. Keep this until
all targets use kernel version with imx sata support in them.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37950
The skb is usually started by a padding which allows the protocols in the
network stack to add their headers in front of the payload. The skb can be
reallocated in case the preallocated padding is not large enough. This can for
example happen in the function __skb_cow which will check the requested extra
headroom and allocate more buffer when the requested headroom is bigger than
the available one. The extra buffer is aligned again to the multiple of the
NET_SKB_PAD of the target architecture.
The macro used to create the multiple of the NET_SKB_PAD is written in a way
which allows only values power two as alignment parameter. The currently used
value of 48 bytes can not be written as n ** 2 but as 2 ** 4 + 2 ** 5. The
extra buffer is therefore not always the multiple of 48 but can be 16, 64, 80,
128, 144 and so on. The generated values are also not monotonic (48 requested
bytes are mapped to 80 allocated bytes and 49 requested bytes are mapped to 64
allocated bytes).
These unexpected small values result in more reallocations of the buffer. This
was noticed prominently during tests between two QCA9558 720 MHz devices which
were connected via ethernet to PCs and had a HT40 802.11n 3x3 link between each
other. The throughput PC-to-PC during iperf TCP runs increased reliable from
186 Mibit/s to 214 Mibit/s in one direction and from 195 Mibit/s to 220 Mibit/s
in the other direction. This is a performance increase of ~14% just by reducing
the amount of reallocations.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 37948
- introduces persistent null session to allow access to procedures without login
- implements session.login procedure to support user logins via json-rpc
SVN-Revision: 37941
SPARC builds are currently broken because we do not define the MUSL
dynamic linker name, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37938
Currently, the module causes an oops at least on rt5350. These patches
have been accepted upstream at:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net.git
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 37931
- adds support for service triggering on config commit
- adds uci transaction support
- adds daemon reload support without loosing session data
- exports headers for use by external plugins
- drops LuCI2 in favor to an out of tree plugin
SVN-Revision: 37921
Hauke Mehrtens