fix in sdhci Use ralink_soc == MT762X_SOC_MT7621AT instead of CONFIG_SOC_MT7621 which is
wrong and breaks builds on mt7620a-similar platforms (MT7621, MT7688)
Signed-off-by: Andrew Yong <me@ndoo.sg>
If something goes wrong and script can't find upstream revision it will
return something like:
r2220
which looks like a valid upstream revision 2220. We cant' distinguish it
from e.g. 2200 upstream commits and 20 local ones.
The new format still provides revision number but also points clearly
that is may be not the upstream one:
r0+2220
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: John Crispin < john@phrozen.org>
The host-side build of grub2 requires this sometimes.
This will re-generate the ./configure script from configure.ac.
I don't know the conditions of how this reproduces, it just
sometimes appears, and sometimes doesn't.
Build error
```
<lede-dir>/build_dir/target-x86_64_musl-1.1.15_yogi/host/grub-2.02~beta2/build-aux/missing: line 81: aclocal-1.14: command not found
WARNING: 'aclocal-1.14' is missing on your system.
You should only need it if you modified 'acinclude.m4' or
'configure.ac' or m4 files included by 'configure.ac'.
The 'aclocal' program is part of the GNU Automake package:
<http://www.gnu.org/software/automake>
It also requires GNU Autoconf, GNU m4 and Perl in order to run:
<http://www.gnu.org/software/autoconf>
<http://www.gnu.org/software/m4/>
<http://www.perl.org/>
Makefile:3962: recipe for target 'aclocal.m4' failed
```
Adding PKG_FIXUP adds sanity (i.e. autoreconf is used for host & target
builds) over just using HOST_FIXUP.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Enable work-arounds present in the code commented-out but needed to write to
sdcard on mt7621 which currently causes kernel to oops when engaging in
serious writing to sdcard. With this change applied, there are still
occasional warnings thrown by the mmc driver, however, at least it no longer
crashes the system and even large writes (full-card dump/erase/write/compare)
don't show any corruption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rebase to LEDE and added "CONFIG_SOC_MT7621" check to ensure non-MT7621 devices do not face performance regressions.
Signed-off-by: Andrew Yong <me@ndoo.sg>
This adds the patch submitted to upstream that adds BQL to the mvneta
driver: https://patchwork.kernel.org/patch/9328413/. Helps latency under
load when the physical link is saturated.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This patch adds header support for the Cisco Meraki MX60/MX60W, which
are a part of the apm821xx target. Some structure changes were needed
due to the fact this device uses U-Boot (unlike other devices in
mkmerakifw.c) which uses a different header structure to define the load
offsets for the image.
A thanks to Christian for helping implement this properly.
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Parameters for dwc2 on lantiq.
A separate dwc2_core_params structure is defined for danube because danube
fifo sizes are large enough to be autodetected. This is not the case on
arx and vrx.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Device tree binding for dwc2 usb driver on danube.
Leave old ifxhcd-danube driver as an alternative.
Also adds dr_mode = "host" to eliminate warning on boot.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
This patch adds support for the Cisco Meraki MX60/MX60W Security
Appliance. Flashing information can be found at
https://github.com/riptidewave93/LEDE-MX60
Specs are as follows:
AppliedMicro APM82181 SoC at 800MHz
1GiB NAND - Samsung K9K8G08U0D
512MB DDR RAM - 4x Nanya NT5TU128M8GE-AC
Atheros AR8327-BL1A Gigabit Ethernet Switch
1x USB 2.0 Port
More info can be found at https://wiki.openwrt.org/toh/meraki/mx60
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This patch fixes the ethernet switch initial config for Mikrotik RB450 and RB450G.
The previous version wrongly changed the RouterStation Pro config. This one creates a specific config for the RB450G and leaves the RouterStation Pro unchanged.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.
Use the same flash approach as for YunCore AP90Q.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Flash instruction under vendor fimrware, using telnet/SSH:
1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.
There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size
Version number is available only inside vendor GUI,
hardware and markings are the same.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.
All 3 devices are based on Qualcomm/Atheros QCA9531 v2.
COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Update patch to remove pipetypes var declaration which was throwing
unused variable warning due to the original patch removing the only use.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Fix the incorrect usage of ar934x_nfc_write_page and ar934x_nfc_write_page_raw.
Add *page* in the argument list and remove the local variable.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Recent refactoring introduced a regression. It ignored second argument
of make_support_list function which was originally true for C2600. The
new generic build_image function always passes false.
This patch allows specifying trailing char in a device specific info. It
also switches Archer C9 to the \0 char to make it compliant with vendor
images.
I verified generated images to be binary identical to the ones that
were created before whole refactoring.
Reported-by: Jo-Philipp Wich <jo@mein.io>
Fixes: fd924d2068 ("firmware-utils: tplink-safeloader: use one function for generating images")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes parsing partition placed after TRX with block-aligned length.
It's important e.g. for Archer C9 which has TRX with kernel only and
rootfs as separated partition.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fix build on targets not using CONFIG_MODULE_STRIPPED.
Neither RTL8367_DRIVER_DESC nor RTL8367B_DRIVER_DESC are defined
anywhere. It worked for targets using CONFIG_MODULE_STRIPPED since our
module stripper no-ops the various module info macros.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Change grub's root device to xen/xvda,msdos1 for the x86_xen_domu
target so that it will boot without further changes.
Signed-off-by: Wilfried Klaebe <w+lede-project@chaos.in-kiel.de>
[Jo-Philipp Wich: fixed and rebased patch from FS#264, added subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Use fwtool to extract it, only require metadata to be present if the
platform sysupgrade script sets REQUIRE_IMAGE_METADATA=1
Image metadata is in JSON format and contains a list of supported
devices, along with version information that could be displayed by a UI
later before the actual upgrade happens.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This will be used to append extra information to images which allows the
system to verify if an image is compatible with the system.
The extra data is appended to the end of the image, where it will be
ignored when upgrading from systems that do not process this data yet:
If the image is a squashfs or jffs2 image, the extra data will land
after the end-of-filesystem marker, where it will be overwritten once
the system boots for the first timee.
If the image is a sysupgrade tar file, tar will simply ignore the extra
data when unpacking.
The layout of the metadata/signature chunks is constructed in a way
that the last part contains just a magic and size information, so that
the tool can quickly check if any valid data is present without having
to do a pattern search throughout the full image.
Chunks also contain CRC32 information to detect file corruption, even
when the image is not signed.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
SafeLoader is image format used by some TP-LINK devices. This tool
allows extracting selected partitions out of it. It can be used for
sysupgrade.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Andrew Yong