Factory image can be installed via Zyxel WebUI.
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch refreshes the ipq806x kernel patches.
There was a large PR for ipq806x in the queue when the kernel patches
were refreshed for 4.4.32, so currently there is quite much fuzz for
ipq806x.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.
The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.
The stock firmware uses the following mac addresses:
LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5: 00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)
Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
2.4GHz: 00:0C:F6:AA:BB:D8
LAN: 00:0C:F6:AA:BB:D9
WAN: 00:0C:F6:AA:BB:DA
5 GHz: 00:0C:F6:AA:BB:DC
The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.
There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.
Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a powerful API for parallel crypto from which many other modules
can benefit. It only winds up being turned on on SMP systems, which
means this adds 0 bytes to the kernel on tiny machines, while only
adding a small bit to SMP systems for big performance improvements.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reboot of 519a199cbc
Which broke other builds.
This time, added compile flags to build only for POWERPC archs
Tested on mpc85xx, ar71xx and bcm2708.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Updating spi pins configuration in R7800 and C2600 DTs
Adding more usb power pin export and gsbi6 in R7800 DT
Updating and fixing leds
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The patch #179 for RPM has initially been made for apq806x board. It has been modified to support ipq806x instead of apq8064.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Adds Google's mirror as primary source and kernel.org as fallback.
Same as commit 0d4f02dfd6
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
In Device/ls1012ardb IMAGES variable, there are two separate firmware
references to the same packages, while do mult-job compile, the same package
build process will arise conflict occasionally. So, only reserve one ext4 fs
as the default firmware.bin.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Adds Google's mirror as primary source and kernel.org as fallback.
Same as commit 0d4f02dfd6
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
OpenMesh devices have often LEDs which are not yet used by OpenWrt. These
should still be available as disabled LEDs in the system configuration for
easier modification.
Signed-off-by: Jaylin Yu <jaylin.yu@open-mesh.com>
[sven.eckelmann@open-mesh.com: Remove LEDs already specified via diag.sh,
add wifi/status LEDs]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
TI wl18xx and wl12xx are Wi-Fi/Bluetooth combo modules
that could be found on different existing boards.
But it is possible to get those modules as a separate
component and use with existing boards as well as
new boards equipped with either module may appear so we
remove dependency on OMAP instead we add dependency on MMC
because this Wi-Fi module uses SDIO interface.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
MMC support has been added to x86-64 a while ago, there is no reason not
to support it in x86-generic as well.
Signed-off-by: Andreas Ziegler <github@andreas-ziegler.de>
[Matthias Schiffer: add commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
PATA support has been removed from x86-generic without any note in LEDE
r538. Not including them makes the generated images incompatible with older
(and some newer) hardware without any significant gain.
Add it back, and also add the same drivers (as far as available) to x86-64.
Signed-off-by: Andreas Ziegler <github@andreas-ziegler.de>
[Matthias Schiffer: add back x86-generic, update commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Polling every 40ms causes more than 10% CPU load on weak devices. An
interval of 200ms is much more reasonable.
Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net>
[Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Without setting the HSR to the selected channel, the WLAN of the UAP
Outdoor+ will exhibit high packet loss in RX.
Based-on-patch-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Rafał Miłecki