This also makes the detection more flexible, as it doesn't need to check
for each model explicitly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are many targets using user space scripts to generate firmware but
bcm53xx doesn't need this, so let's disable that kernel option.
This lets us avoid some scary-looking kernel warnings like:
brcmfmac 0001:04:00.0: Falling back to user helper
firmware brcm!brcmfmac43602-pcie.txt: firmware_loading_store: map pages failed
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
/etc/preinit has been the default init-script for a very long time (at
least since Linux 2.6.30 in OpenWrt). Remove the kernel command line
"init" parameter to get rid of duplicate and inconsistent definitions
of this parameter (some boards, like FRITZ3370 for example did not use
it at all, while it's just copy and paste on others).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Use devicetree's /chosen/stdout-path instead of the kernel command line
(embedded in the .dts-files) to specify the serial console. Using the
chosen node is recommended on devicetree based platforms.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.
YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.
Common specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm
SR3200 specification:
- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB
XD3200 specification:
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB
LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.
Flash instruction under vendor firmware, using telnet/SSH:
1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
This attribute is not evaluated any more and the boot loader on these
reference boards does not provide a broken root= or console= parameter.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add an extra function to patch the mac and fixup the checksum
afterwards. Calculate the checksum position automatically. The offset
to the mac address is the same for all checksum protected EEPROMs.
No EEPROM requires a byte swapped mac address. The mac byte swap code
was required due to an bug in the script that is now fixed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The EEPROM data in the flash of the ARV7518PW, ARV8539PW22,
BTHOMEHUBV2B and BTHOMEHUBV3A is stored byte-swapped (swab16), meaning
that for example the ath9k base_eep_header fields "version" (high and
low byte), "opCapFlags" and "eepMisc" are swapped (the latter ones are
just 1 byte wide, thus their position is swapped).
The old "ath,eep-endian" property enabled the corresponding swapping
logic in the ath9k driver (swab16 in ath9k_hw_nvram_swap_data, which is
based on the magic bytes in the EEPROM data which have nothing to do
with the calibration data - thus this logic should not be used
anymore).
Since we have switched to the upstream ath9k devicetree bindings there
is no binding anymore which enables swab16 in ath9k (as this logic is
not recommended anymore as explained above), leading to ath9k
initialization errors:
ath: phy0: Bad EEPROM VER 0x0001 or REV 0x00e0
(this shows that the version field is swapped, expected values are VER
0x000E and REV 0x0001)
Swapping the ath9k calibration data when extracting it from the flash
fixes the devices listed above (all other devices do not require
additional swapping, since the position of the fields is already as
expected by ath9k). This allows ath9k to read the version correctly
again, as well as the more important "eepmisc" field (which is used for
determining whether the data inside the EEPROM is Big or Little Endian
which is required to parse the EEPROM contents correctly).
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Rob suggested I should use of_machine_is_compatible insteak of a new
property and updated patch has been sent.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is helpful for Orion-based NAS boxes that have the XOR engine enabled
since it provides faster software RAID.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The harddisk target is for NAS boxes, so set the DEVICE_TYPE accordingly so we
get a sensible default package selection.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable support for this machine in the kernel and also produce valid image
files with the correct machine id.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Needed to work around ethernet hang issues on Ubiquiti NanoStation Loco XW,
because ar71xx is not converted to device tree yet.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
By default, forwarding between all ports is allowed on init. This is
problematic in cases where some ports are supposed to be isolated from
each other, most commonly LAN/WAN separation.
REG_ESW_PORT_PCR(port) has a destination mask for a particular port,
controlling what other ports it is allowed to send packets to.
Instead of initializing all to 0xff (all ports), allow each physical
port to send to the CPU port, and the CPU port to send to all other
ports.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.
Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.
Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
sysupgrade command fails due to missing U-Boot environment-processing
binaries on sysupgrade ramdisk. The missing binaries result in the
following output:
Switching to ramdisk...
Performing system upgrade...
ash: /usr/sbin/fw_printenv: not found
ash: fw_setenv: not found
ash: touch: not found
cannot find target partition
Signed-off-by: Vignesh Balasubramaniam <vigneshb.hp@gmail.com>
Rafał Miłecki