The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.
The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.
Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).
For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Fix a typo in mt7621.dtsi compatible string. Disable spi, sdhci and pci
in mt7621.dtsi and enable the nodes in the indiviual board dts files.
The nodes require further device specific configuration anyway.
Remove the m25p80@0 spi child node from mt7621.dtsi and add the
chunked-io parameter to the individual board dts files. Fix the spi
flash compatible string for the WNDR3700V5.
Drop the mt7621-eval-board compatible string for all boards which are
not the eval board.
Drop the linux,modalias parameter from spi flash node.
Remove the xhci node from board files, it is already enabled in dtsi.
Disable xhci for boards not having usb ports populated.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The 10.1 includes a good many stability fixes related to the effort of
backporting upstream 10.2 firmware. Also enables 802.1q vlan support.
Successfully tested on apu2.
The 10.4 firmwares including new backported code as well as stability
fixes. 10.4 has been tested on Fedora x86-64 platforms, but not on LEDE
specifically since I had issues compiling LEDE for my 9980/9984 AP hardware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Fix configuration files for the Livebox 1 routers.
- Add status led
- Set eth0 as the LAN port, for coherence with RedBoot and comfortability.
- Add led triggers
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix Image generation for the Livebox 1
- missing "relocate-kernel", wrong "LOADADDR", fix it
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the DTS file for the Livebox 1 routers:
- part probe wrong, it should be RedBoot (uppercase matters)
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the DTS file for the Livebox 1 routers:
- leds are totally wrong, fix them.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the DTS file for the Livebox 1 routers:
- no failsafe button, use button 1 for this purpose
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Packages that do a killall <cmd> with the same name as the init script
will fail the prerm step when the service isn't running. Do make them
removable without having to restart the service, ignore the return code.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
To make sure we properly restart services on upgrade we need to
call the prerm script of the old package, in case the init script
changes (or vanishes).
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Properly stop/start services on upgrade, but don't change the enabled
state.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Allow scripts from the package to be upgraded to be aware of being
upgraded.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
fix in sdhci Use ralink_soc == MT762X_SOC_MT7621AT instead of CONFIG_SOC_MT7621 which is
wrong and breaks builds on mt7620a-similar platforms (MT7621, MT7688)
Signed-off-by: Andrew Yong <me@ndoo.sg>
If something goes wrong and script can't find upstream revision it will
return something like:
r2220
which looks like a valid upstream revision 2220. We cant' distinguish it
from e.g. 2200 upstream commits and 20 local ones.
The new format still provides revision number but also points clearly
that is may be not the upstream one:
r0+2220
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: John Crispin < john@phrozen.org>
The host-side build of grub2 requires this sometimes.
This will re-generate the ./configure script from configure.ac.
I don't know the conditions of how this reproduces, it just
sometimes appears, and sometimes doesn't.
Build error
```
<lede-dir>/build_dir/target-x86_64_musl-1.1.15_yogi/host/grub-2.02~beta2/build-aux/missing: line 81: aclocal-1.14: command not found
WARNING: 'aclocal-1.14' is missing on your system.
You should only need it if you modified 'acinclude.m4' or
'configure.ac' or m4 files included by 'configure.ac'.
The 'aclocal' program is part of the GNU Automake package:
<http://www.gnu.org/software/automake>
It also requires GNU Autoconf, GNU m4 and Perl in order to run:
<http://www.gnu.org/software/autoconf>
<http://www.gnu.org/software/m4/>
<http://www.perl.org/>
Makefile:3962: recipe for target 'aclocal.m4' failed
```
Adding PKG_FIXUP adds sanity (i.e. autoreconf is used for host & target
builds) over just using HOST_FIXUP.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Enable work-arounds present in the code commented-out but needed to write to
sdcard on mt7621 which currently causes kernel to oops when engaging in
serious writing to sdcard. With this change applied, there are still
occasional warnings thrown by the mmc driver, however, at least it no longer
crashes the system and even large writes (full-card dump/erase/write/compare)
don't show any corruption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rebase to LEDE and added "CONFIG_SOC_MT7621" check to ensure non-MT7621 devices do not face performance regressions.
Signed-off-by: Andrew Yong <me@ndoo.sg>
This adds the patch submitted to upstream that adds BQL to the mvneta
driver: https://patchwork.kernel.org/patch/9328413/. Helps latency under
load when the physical link is saturated.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This patch adds header support for the Cisco Meraki MX60/MX60W, which
are a part of the apm821xx target. Some structure changes were needed
due to the fact this device uses U-Boot (unlike other devices in
mkmerakifw.c) which uses a different header structure to define the load
offsets for the image.
A thanks to Christian for helping implement this properly.
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Parameters for dwc2 on lantiq.
A separate dwc2_core_params structure is defined for danube because danube
fifo sizes are large enough to be autodetected. This is not the case on
arx and vrx.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Device tree binding for dwc2 usb driver on danube.
Leave old ifxhcd-danube driver as an alternative.
Also adds dr_mode = "host" to eliminate warning on boot.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
This patch adds support for the Cisco Meraki MX60/MX60W Security
Appliance. Flashing information can be found at
https://github.com/riptidewave93/LEDE-MX60
Specs are as follows:
AppliedMicro APM82181 SoC at 800MHz
1GiB NAND - Samsung K9K8G08U0D
512MB DDR RAM - 4x Nanya NT5TU128M8GE-AC
Atheros AR8327-BL1A Gigabit Ethernet Switch
1x USB 2.0 Port
More info can be found at https://wiki.openwrt.org/toh/meraki/mx60
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This patch fixes the ethernet switch initial config for Mikrotik RB450 and RB450G.
The previous version wrongly changed the RouterStation Pro config. This one creates a specific config for the RB450G and leaves the RouterStation Pro unchanged.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.
Use the same flash approach as for YunCore AP90Q.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Flash instruction under vendor fimrware, using telnet/SSH:
1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.
There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size
Version number is available only inside vendor GUI,
hardware and markings are the same.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.
All 3 devices are based on Qualcomm/Atheros QCA9531 v2.
COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Update patch to remove pipetypes var declaration which was throwing
unused variable warning due to the original patch removing the only use.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Fix the incorrect usage of ar934x_nfc_write_page and ar934x_nfc_write_page_raw.
Add *page* in the argument list and remove the local variable.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Eddi De Pieri