The short git hash suffix printed by getver.sh is taken from the
latest local commit, change this to use the hash from latest
upstream commit if available. This is considered the intended
behavior based on commit message a642a11fac,
introducing getver.sh.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We override default Ethernet interface with eth0 which often uses random
MAC due to missing proper NVRAM entry. Fix this by manually assigning
MAC in the config.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Since the main stamp file depends on the _check stampfile, the _check
stampfile needs to be created on the first run as well.
Fixes spurious rebuilds with CONFIG_AUTOREBUILD=y
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All mvebu boards have three USB LEDs. The first one is used for the
USB1 port.
There are two LEDs related to the second USB port. The top (bar) LED
gets bright in case any USB device is connected to the second USB port.
If the connected device is an USB 3 (SuperSpeed) device, the small dot
LED bellow the "bar" LED gets also bright.
While at it, use a name for the USB LEDs that matches the names printed
on the case.
Fixes: FS#423, FS#425
Signed-off-by: Kabuli Chana <newtownbuild@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a pure rename without any changes. It makes maintaining bgmac
simpler and will hopefully make adding new kernel a bit easier.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Some debugging/error messages are printed using wpa_printf and this
change allows finally reading them out of the syslog.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This will allow starting hostapd with the new -s parameter and finally
read all (error) messages from the syslog.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Buffalo WCR-1166DS is a small wireless router with
- MT7628AN + MT7612E
- 64MiB DDR2 SDRAM
- 16MiB SPI flash
- 2T2R 11ac/a/b/g/n Wi-Fi
- 2x 10/100M ethernet switch
- 8x programmable LED
- 3x button
- UART pad on PCB (J2: 3.3V, GND, TX, RX)
factory image can be installed via stock web UI.
due to the "dual image" function in the bootloader, the second half of
the SPI flash ("firmware2" partition) cannot be used as a part of the
file system.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
only factory images for DHP-EU and DHP2-JP (fw ver. 2.x) are built.
this will not work for DHP-JP/AP/TW (fw ver. 1.x) because they use
different buffalo_csum() formula.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
some of Buffalo DHP series use slightly different trx magic, buffalo-enc,
buffalo-tag, and factory image begin with 'bgn'.
this patch adds support for building those images.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Qemu's local AES code defines symbols that conflict with
LibreSSL/OpenSSL's libcrypto. Rename them to avoid build problems.
See upstream commit c8d70e59738e672021926c7747af8ef9dea15c82.
Fixes FS#444.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
wash, mpu & some memory optimisation have now made it to the official
cake repository.
Point LEDE to the official repository.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
c13b6a0 dhcpv6: fix white space error
e9d80cc dhcpv6: trigger restart of DHCPv6 state machine when not
receiving statefull options
c7122ec update README
419fb63 dhcpv6: server unicast option support
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The condition is always true due to the literal string followed the
-n test parameter. A model name set by target scripts always gets
overwritten this way.
Change the condition to check for an already existing destination file
as it was before 5e85ae9 ("base-files: fix error message during boot").
Signed-off-by: Mathias Kresin <dev@kresin.me>
It wasn't possible to read hostapd wpa_printf messages unless running
hostapd manually. It was because hostapd was printing them using vprintf
and not directly to the syslog.
We were trying to workaround this problem by redirecting STDIN_FILENO
and STDOUT_FILENO but it was working only for the initialization phase.
As soon as hostapd did os_daemonize our solution stopped working.
Please note despite the subject this change doesn't affect debug level
messages only but just everything printed by hostapd with wpa_printf
including MSG_ERROR-s. This makes it even more important as reading
error messages can be quite useful for debugging.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes build issues with some toolchains that don't add lcrypt in the default
search paths:
CMakeFiles/rpcd.dir/session.c.o: In function `rpc_login_test_password':
build_dir/target-mipsel-linux-gnu/rpcd-2016-12-03-0577cfc1/session.c:823: undefined reference to `crypt'
collect2: error: ld returned 1 exit status
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Some toolchains will produce executables with an interpreter that is e.g:
ld.so.1 (typically a symbolic link). Due to our current LIBC_SPEC_FILE value,
we would not be able to copy this symbolic link/file over to the rootfs and
executables would fail to load. Extend the search pattern to include all
ld*.so* files that could be needed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
For external toolchain, we also know the type of C library used, and the
toolchain triplet may not always be reflective of that, therefore make
$(TARGET_DIR_NAME) suffixed with _$(LIBC).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This fixes logic bug(in function netdev_trig_notify) introduced in
0b2991a8ed commit.
Events triggered by different interfaces were stopping work queue so it
wasn't working for tx/rx mode.
Signed-off-by: Sergey Sergeev <adron@yapic.net>
Refresh patches, delete patches that have been applied upstream.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [fix defaults]
The "new style" busybox applet approach moves all config and build
definitions related to an applet to its .c file. This makes the
patches easier to maintain, as they only add new files to the busybox
build directory, without modifying BusyBox files.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Commit 29443e2 (mxs: remove modules.mk, select drivers in the kernel config)
missed to remove these references, so cleanup it now.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
The VGV7510KW22BRN and VGV7519BRN do not have the same brnImage
signature. It was accidentally changed with ba42c1d ("lantiq: un-macro
the image building code").
Signed-off-by: Mathias Kresin <dev@kresin.me>
This fixes the following security problems:
CVE-2017-3731: Truncated packet could crash via OOB read
CVE-2017-3732: BN_mod_exp may produce incorrect results on x86_64
CVE-2016-7055: Montgomery multiplication may produce incorrect results
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit e79ecb4c26.
The commit was incomplete and the issue that should be fixed isn't
that easy fixable. The Archer C7 mach file is used for the Archer C5,
WDR4900 and WDR7500 as well. Where the WDRs in compare to the Archer
do have blue LEDs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not put the apex images into the kernel build directory as this directory
might get removed after kernel updates while the apex packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Felix Fietkau