&wmac entry in WIZnet WizFi630S dts file was existing two times.
This is removing one of them.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
(cherry picked from commit b735bbcb1876196f33f044ed07325f8959a8967f)
WIZnet WizFi630S is using only 3 of the phy ports. The unused phy ports
draw unnecessarily power. This is disabling the unused phy ports.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
(cherry picked from commit 36d4c2272ec65490232e70d45b945b9f467b78f0)
The comments in code already describe the intended lan / wan assignment:
lan: switch
wan: standalone ethernet and sfp
Update the interface handles to match the comments, as observed with
OpenWRT-19.07-rc2 on a Clearfog Pro Rev 2.0.
This also matches the effective assignment on master, while the actual
interface names (ethX) are different due to the reassignment in
06_set_iface_mac, which is included in 19.07 but was dropped for master.
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
[extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit 1bfbf2de6d ("ar71xx: serial: core: add support for boot console
with arbitrary baud rates") added support for arbitrary baud rates which
enabled 250000 baud rate for Yun. But the patch was not ported to kernel
4.9, and since then the kernel set its baud rate to 9600. This commit ports
the patch to kernel 4.14, thereby restoring the serial console of Yun.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit c90db26e051e4f0e7cd32333b3bd8c94a13d599a)
The Arduino Yun uses a baud rate of 250000 by default. The serial is
going over the Atmel ATmega and is used to connect to this chip.
Without this patch Linux wants to switch the console to 9600 Baud.
With this patch Linux will use the configured baud rate and not a
default one specified in uart_register_driver().
This has been added for ath79 4.19 and 5.4 in master as part of
fc59b2f79b50 ("ath79: add support for Arduino Yun"), this backports
it separately to 4.14.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit 05d73a2a73 enabled GPIO on ethernet LED, but proper LED setup was
not added then. This commit fixes it by reverting the change on the LED.
Fixes: 05d73a2a73 ("ar71xx: Arduino Yun board 'WLAN RST' button support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit a5e404d1923d135d335e4ece83f87e6e891396e2)
Commit bb46b635df changed its partition scheme, but sysupgrade image
validation still uses the old format. This commit fixes it so that
force flag is not needed for sysupgrade.
Fixes: bb46b635df ("ar71xx: move Arduino Yun to generic building code")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 58dc1d0637425cfe023192466e6212009332b677)
This reverts commit 077253dd66.
The output enable pins should be disabled by default, and only enabled when
used. Otherwise unwanted conflicts might occur between MCU and SoC pins.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 43896dc0b005adfb512c027a27781c971440d415)
ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should
be in the default image for this device.
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(backported from commit 0a182fcba6d9cb2cf74cae9114ea4770ef928f75)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In FS#2738 we can see that patch first introduced in
e8ebcff ("ramips: add a explicit reset to dwc2")
breaks USB functionality since 18.06. Thus, this patch should be removed.
Removed:
- 0032-USB-dwc2-add-device_reset.patch
Fixes: FS#2738
Fixes: FS#2964
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
(cherry picked from commit ab841b4393a4077a5819da1da040ab9a89e3b69d)
This board ships with an ancient 14.07-based OpenWrt using block2mtd, and
the MBR partition table contains nonsense.
It is possible to sysupgrade to an upstream OpenWrt image, but the
legacy layout of the OpenWrt images start at 0xA00 in the eMMC, with
a raw uImage. The legacy OpenWrt image doesn't "own" the beginning
of the device, including the MBR and U-Boot.
This means that when a user upgrades to upstream OpenWrt, it doesn't
boot because it can't find the right partitions. So hard-code them on
the kernel's command line using CONFIG_CMDLINE_PARTITION (for block).
Additionally, the vendor firmware doesn't cope with images larger than
about 36MiB, because it only overwrites the contents of its "firmware"
MTD partition. The current layout of the legacy image wastes a lot of
space, allowing over 32MiB for the kernel and another 10MiB for the FAT
recovery file system which is only created as 3MiB. So pull those in
to allow 4¾ MiB for the kernel, 3MiB for recovery, and then we have over
20MiB for the root file system.
This doesn't affect the new images which ship with a full eMMC image
including a different MBR layout and a partition for U-Boot, because
our modern U-Boot can actually pass the command line to the kernel, and
the built-in one doesn't get used anyway.
Tested by upgrading from vendor OpenWrt to the current legacy image,
from legacy to itself, to the previous legacy layout, and then to
finally the full-system image.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
(cherry picked from commit 6eb63019afef89404899f2cb65fb4c16e00aa0ed)
The bootloader for legacy builds can't set it, so we end up unable to
log in on the serial port.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
(cherry picked from commit ea9ef8c9451a08aa4dbb6efcbe5f20d9b788ebd2)
The TL-WR841ND v8 feature a WiFi switch instead of a button.
This adds the corresponding input-type to prevent booting into
failsafe regularly.
This has been defined correctly in ar71xx, but was overlooked
when migrating to ath79. In contrast, the TL-WR842ND v2, which
has the key set up as switch in ar71xx, actually has a button.
The TL-MR3420 v2 has a button as well and is set up correctly
for both targets. (Information based on TP-Link user guide)
Note:
While looking into this, I found that support PR for TL-MR3420 v2
switched reset button to ACTIVE_HIGH. However, the other two
device still use ACTIVE_LOW. This seems strange, but I cannot
verify it lacking the affected devices.
Fixes: FS#2733
Fixes: 9601d94138 ("add support for TP-Link TL-WR841N/ND v8")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 5e86877f36b0d95127dcef8ed3abf78ecd78061d)
WRT610N V2 is not detected by the initial network configuration script.
The switch remains unconfigured and wlan/lan vlans are not created.
This adds the correct setup for the device.
Fixes: FS#1869
Suggested-by: Alessandro Radicati
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a2fee73e270305c4cb086055cc30e97f65e6f58b)
Pressing the 'WLAN' button should enable/disable wireless activity.
Currently, the button is mapped to the KEY_WLAN, which will not
have this effect.
This patch changes the mapping of the WLAN button, so a button
press will emit an action for the 'rfkill' key instead of 'wlan'.
Apparently, this is what stock OpenWRT expects.
This fix is analogous to the preceding patch for Fritzbox 3370.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
(cherry picked from commit d5a148f5c8f6d6dee7041fd348bd0f52839d0f4e)
The WLAN button actions are reversed, i.e. pressing the button emits a
'released' action, and vice versa.
This can easily be checked by adding
logger -t button_action "$BUTTON $ACTION"
as the second line of /etc/rc.button/rfkill, and using logread to read
the events (assuming the preceding patch has been applied).
Defining the GPIO as ACTIVE_LOW corrects this behavior.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
(cherry picked from commit 0ee30adb46a87583badd85b69e4ccd7942786374)
Pressing the 'WLAN' button should enable/disable wireless activity.
However, on the Fritzbox 3370 this doesn't have an effect.
This patch changes the mapping of the physical WLAN button, so a button
press will emit an action for the 'rfkill' key instead of 'wlan'.
Apparently, this is what stock OpenWRT expects, and also what is
implemented for most other devices.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
(cherry picked from commit a53bf63756ef2a266ae5f3b3507eeb7382b4cdc9)
As the the SoC uses implicit vlan tagging for dual MAC support, the
offload feature breaks when using double tagging.
This is backport of 9da2b567605b0964d921b9ca4f0c9886db4f636d from trunk.
As the layout of the files has changed a cherry-pick was not possible.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: John Crispin <john@phrozen.org>
Pogoplug V4 has a reset button on a GPIO pin.
To use it, kmod-gpio-button-hotplug package needs to be installed.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 91472dc2ce051d255eecb7fbba3484de917fa65d)
Move the USB VBUS regulator nodes out of the GPIO controller node. This
fixes a problem where the "regulator-fixed" driver wasn't probed for
these regulators because the GPIO driver doesn't scan the child-nodes
and based on the dt-bindings documentation it's not supposed to.
This fixed the following error reported by Luca Olivetti:
...
dwc2 1e101000.usb: DWC OTG Controller
dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
dwc2 1e101000.usb: irq 62, io mem 0x1e101000
dwc2 1e101000.usb: startup error -517
dwc2 1e101000.usb: USB bus 1 deregistered
dwc2 1e101000.usb: dwc2_hcd_init() FAILED, returning -517
Fixes: FS#1634
Cc: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[backported from 982468de35d499f85470b7b547d2b27cea53bae0]
Signed-off-by: Luca Olivetti <luca@ventoso.org>
This fixes the following compile error:
drivers/mtd/nand/rb91x_nand.c: In function 'rb91x_nand_remove':
drivers/mtd/nand/rb91x_nand.c:445:16: error: 'rbni' undeclared (first use in this function)
nand_release(&rbni->chip);
Fixes: 9cad70044f ("kernel: fix nand_release() usage.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 66e04abbb6d0dec8642be5deb2fca4bba470f8ac)
There is one closing bracket too much.
Fixes: 9cad70044f ("kernel: fix nand_release() usage.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 014d3f593acea13ee6aa002d858f182806ed43f0)
Upstream in commit f9f8f0c24203 ("crypto: ccp -- don't "select"
CONFIG_DMADEVICES") removed dependency on CONFIG_DMADEVICES symbol which
leads to build breakage of ccp crypto module, so fix this by adding that
symbol back in the kernel config.
Fixes: f4985a22ca ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 472b8fc91bbab0530d72e9780a482bacc1bbe5f7)
For quite some time, the tiny (4M flash) TP-Link sysupgrade and
factory images cannot be built anymore by the buildbots, just
the initramfs-kernel.bin files are still there.
Disable these images for the buildbots and don't waste build
resources.
Note that these devices still build fine with default settings,
just not with the additional packages and config symbols for
the buildbots.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The uci config section network.globals set up in /bin/config_generate
will only be created if /proc/sys/net/ipv6 exists.
Correspondingly, lacking IPv6 support, the command
uci set network.globals.packet_steering=1
will fail with "uci: Invalid argument" as the network.globals config
has not been set up.
Fix that by adding the setup there as well.
While at it, limit the uci commit to the network config file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 636b62e8e232951154ac4ccd7972fda3f8de0379)
Fix the switch LAN labels for the DGND3700v1/DGND3800B router,
the order is reversed.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[cut out of bigger patch, adjust commit title/message accordingly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 583b3e40254076693eb5227a9d9ae49eb2b0bcbf)
Increase the SPI frequency for ELECOM WRC-1900GST and WRC-2533GST
to 40 MHz by updating the common DTSI file.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[WRC-1900GST]
Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit b5ae70d0530d1a733816f921ae0fe4dd58251fbb)
The mwlwifi driver sets the default country code for EU (fi-
rmware region code 0x30) certified devices to FR (France),
not DE (Germany). Whilst this is a trivial fix, novice users
may not know how mwlwifi negatively reacts to a non-matching
country code and may leave the setting alone. Especially si-
nce it is under the advanced settings section in LuCI.
Relevant mwlwifi driver code:
0a550312dd
The mwlwifi driver readme states "Please don't change country
code and let mwlwifi set it for you." However, OpenWrt's current
behaviour does not adhere to this with its default, 'just flashed
from factory' setting for EU devices.
Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d0e8b8310f7079ccf250f7eddbdf8b9d319c274d)
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.
The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi
While this is a cosmetic change, backporting it to 19.07 will be a
major help for anyone doing backports of device support. Without it,
every backporter would have to remember to manually add the chosen node
to the device's DTS.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 635f111148c3f7ccb0ecc92863a3b1a142f6ebeb)
This ports support for these devices from ar71xx.
Specification:
- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: v3: 560 MHz, v4: 650 MHz
- Flash: 4096 KiB
- RAM: 32 MiB
- Ethernet: 1 port @ 100M
- Wireless: SoC-integrated: QCA9533 2.4GHz 802.11bgn
In contrast to the implementation in ar71xx (reset and WiFi button),
the device actually features reset and WPS buttons.
Flashing instructions:
Upload the ...-factory.bin file via OEM web interface.
TFTP Recovery:
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to
wa801ndv3_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
TFTP recovery has only been tested with v3, and the Wiki states
that the procedure won't work for v4, which cannot be verified
or falsified at the moment.
Tested by Tim Ward (see forum):
https://forum.openwrt.org/t/ath79-support-for-tp-link-tl-wa901nd-v3-v4-v5/61246/13
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 9a477b833ab2aea96b9eee55acb5f9e7b01b36d8)
The Pirelli A226M-FWB has a wrong linux partition offset, caused
by a copy-paste error. As of result of this, OpenWrt is currently
broken in this unit.
Fix it.
While at it, also use generic node names and fix the addresses
there as well.
Fixes: a27d59bb42 ("brcm63xx: switch to new partition layout
specification")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[also fix/update node names, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d64d5ed1425f4397d093c8777ca03f70ff1ee90c)
It was noticed that the the whole MAC can hang when transferring data from
one ar40xx port (WAN ports) to the CPU and from the CPU back to another
ar40xx port (LAN ports). The CPU was doing only NATing in that process.
Usually, the problem first starts with a simple data corruption:
$ wget https://cdimage.debian.org/debian-cd/current/amd64/iso-cd/debian-10.4.0-amd64-netinst.iso -O /dev/null
...
Connecting to saimei.ftp.acc.umu.se (saimei.ftp.acc.umu.se)|2001:6b0:19::138|:443... connected.
...
Read error at byte 48807936/352321536 (Decryption has failed.). Retrying.
But after a short while, the whole MAC will stop to react. No traffic can
be transported anymore from the CPU port from/to the AR40xx PHY/switch and
the MAC has to be resetted.
The whole problem can be avoided by disabling IPv6 TSO for this ethernet
MAC driver.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: John Crispin <john@phrozen.org>
(backported from commit 678569505623e50bbbbc344c7e820fb315b79ede, with
updated commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds ar71xx's GPIO setup for the 2.4GHz and 5GHz antennae
demultiplexer:
| 158 /* 2.4 GHz uses the first fixed antenna group (1, 0, 1, 0) */
| 159 ap9x_pci_setup_wmac_gpio(0, (0xf << 6), (0xa << 6));
| 160
| 161 /* 5 GHz uses the second fixed antenna group (0, 1, 1, 0) */
| 162 ap9x_pci_setup_wmac_gpio(1, (0xf << 6), (0x6 << 6));
This should restore the range and throughput of the 2.4GHz radio
on all the derived wndr3700 variants and versions with the AR7161 SoC.
A special case is the 5GHz radio. The original wndr3700(v1) will
benefit from this change. However the wndr3700v2 and later revisions
were unaffected by the missing bits, as there is no demultiplexer
present in the later designs.
This patch uses gpio-hogs within the device-tree for all
wndr3700/wndr3800/wndrmac variants.
Notes:
Based on the PCB pictures, the WNDR3700(v1) really had eight
independent antennae. Four antennae for each radio and all of
those were printed on the circut board.
The WNDR3700v2 and later have just six antennae. Four of those
are printed on the circuit board and serve the 2.4GHz radio.
Whereas the remaining two are special 5GHz Rayspan Patch Antennae
which are directly connected to the 5GHz radio.
Hannu Nyman dug pretty deep and unearthed a treasure of information
regarding the history of how these values came to be in the OpenWrt
archives: <https://dev.archive.openwrt.org/ticket/6533.html>.
Mark Mentovai came across the fixed antenna group when he was looking
into the driver:
fixed_antenna_group 1, (0, 1, 0, 1)
fixed_antenna_group 2, (0, 1, 1, 0)
fixed_antenna_group 3, (1, 0, 0, 1)
fixed_antenna_group 4, (1, 0, 1, 0)
Fixes: FS#3088
Reported-by: Luca Bensi
Reported-by: Maciej Mazur
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Debugged-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 61307544d1f1ab81a2eb3a200164456c59308d81)
CONFIG_VLAN_8021Q was explicitely disabled in oxnas kernel config.
Don't do that, so VLANs can be used on the target.
Fixes: dcc34574ef ("oxnas: bring in new oxnas target")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fd0cc72d9ceba6d4dc315c7f0e52d6513023f669)
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of Flash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)
Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to web interface:
[V1] http://192.168.0.1
[V2] http://192.168.0.254
Default user is "admin" & password is "admin".
On V2, there is no DHCP server running by default, so remember to set
IP manually.
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware:
[V1] "*.factory.bin"
[V2] "*.factory-us.bin" or "*.factory-eu.bin" for eu model
Web interface may complain if filename is too long. In such case,
rename .bin to something shorter.
- Click upgrade
Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
Serial Configuration 115200 8n1
- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
(IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
(e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
(e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
(e.g bootm 0x9f020000)
Notes:
When porting from ar71xx target to ath79, I found out that on V2,
reset button is on GPIO12 and active low, instead of GPIO11 and
active high. By cross-flashing V1 firmware to V2, I confirmed
the same is true for V1.
Also according to manual of V1, this one also has green
LED instead of blue - both of those issues were fixed accordingly.
The MAC address assignment has been checked with OEM firmware.
Installation manual based on ar71xx support by Thomas Roberts
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit message, add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 7e513136c63108bf55b38be4d2b65aa00b0d2b26)
Ubiquiti WA devices with newer hw version 2011K require UBNT_VERSION
to be at least 8.5.3, otherwise the image is rejected:
New ver: WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3
Versions: New(525568) 8.5.0, Required(525571) 8.5.3
Invalid version 'WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3'
For consistency, also increase version number for XC devices.
Tested-by: Pedro <pedrowrt@cas.cat>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit 95caa3436d98dac3709e550765f3f86d11a99782)
Since the wireless LED was used for boot and set up with a DT
trigger, the WiFi indication hasn't worked on ath79 at all.
In addition, a look into the manual revealed that the OEM
configuration is as follows:
LED 1 (green): power
LED 2 (green): configurable
LED 3 (red): wireless
So, let's just keep the WiFi trigger and convert the rest to its
"intended" use.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 705fe43522c756962589b360141d4c398363ce1c)
During porting support for this router to ath79 target
it was discovered that GPIO mapping was incorrect (GPIO11 active high).
Correct mapping for both V1 and V2 is GPIO12 active low.
Default configuration from GPL source for V2 explicitly states this, and
this was confirmed experimentally on ath79 by looking on
/sys/kernel/debug/gpio. Correctness of this was also validated for V1 by
cross-flashing vendor firmware for V1 on V2 hardware, in which reset
button also worked.
Fix it.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit f841e706403b1a111cbb6dc5930b7886307bf633)
Make the driver work with recent upstream changes.
Fixes: FS#2632
Ref: https://github.com/openwrt/openwrt/pull/2815
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 6786dc26a205da55ec2d9771693cdfb99e756e59)
The TP-Link TL-MR3020 has a three-state mode slider which was previously
integrated as a button (EV_KEY). This led to spurious activations of
failsafe mode.
Set the type for the button to switch (EV_SW), to avoid unintended
activations of failsafe mode.
Related: commit 27f3f493de06 ("gpio-button-hotplug: unify polled and
interrupt code")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b017a016cc0cd26f84a7e6b8de3dc02dc101e888)
The -O option for the tplink-v1-header was missing for the TP-Link
TL-WR902AC v1, while safeloader and MTDPARTS where set up with a
single firmware partition.
This led to bootloops after using sysupgrade.
Fixes: FS#3118
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a7b07f8ba880895f0d235a63729dd189cb2410a7)
Looking at the current upstream driver implementation, it seems like the
TX/RX flow control is enabled only if the flow control pause option is
resolved from the device/link partner advertisements (or otherwise set).
On the other hand, our current in-tree driver force enables TX/RX
flow control by default, thus possibly leading to TX timeouts if the
other end sends pause frames (which are not properly handled?):
WARNING: CPU: 3 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x1ac/0x324
NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out
Disabling the flow control on PORT 5 MAC seems to fix this issues as the
pause frames are then filtered out. While at it, I'm removing the if
condition completely as suggested, since this code is run only on mt7621
SoC, so there is no need to check for the silicon revisions.
Ref: https://lists.openwrt.org/pipermail/openwrt-devel/2017-November/009882.html
Ref: https://forum.openwrt.org/t/mtk-soc-eth-watchdog-timeout-after-r11573/50000/12
Suggested-by: Felix Fietkau <nbd@nbd.name>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c8f8e59816eca49d776562d2d302bf990a87faf0)
Disable the Netgear WNR2000 v2 image by default as the device has
insufficient flash space for release build images.
Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/72
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
[drop change on netgear-wnr3500l-v1-na]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This ports support for the TL-WA901ND v4 and v5 from ar71xx to ath79.
They are similar to the TP9343-based TL-WR940N v3/v4 and TL-WR941ND v6.
Specifications:
SoC: TP9343
Flash/RAM: 4/32 MiB
CPU: 750 MHz
WiFi: 2.4 GHz b/g/n
Ethernet: 1 port (100M)
Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to * (see below)
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
* The image name for TFTP recovery is wa901ndv4_tp_recovery.bin for
both variants.
In ar71xx, a MAC address with offset 1 was used for ethernet port.
That's probably wrong, but this commit sticks to it until we know
the correct value.
Like in ar71xx, this builds the default factory.bin with EU country
code.
Thanks to Leonardo Weiss for testing on the v5.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 4a61a88f9006f70444e00699f76551c75f73c14e)
This adds support for the various clones of the TL-WA830RE recently
supported in fb99ac6807f2 ("ath79: add support for TP-Link TL-WA830RE v1"):
- tplink,tl-wa701nd-v1
- tplink,tl-wa730re-v1
- tplink,tl-wa801nd-v1
- tplink,tl-wa830re-v1 (already supported)
- tplink,tl-wa901nd-v1
Since these devices are 100%-clones in ar71xx, this patch adds all
of them without run-testing (as this has been done for TL-WA830RE v1).
Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftpboot 0x80000000 \
openwrt-ath79-tiny-tplink_tl-waxxxxx-v1-squashfs-factory.bin
> erase 0x9f020000 +0x3c0000
> cp.b 0x80000000 0x9f020000 0x3c0000
> bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 2f1cc5c3d5e35d6aa76e794e3d5b4f5856cd38bc)
The TL-WR940N v6 is similar to v3/v4, it just has different
LEDs and MAC address assignment.
Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet
The use of LEDs is based on ar71xx, so blue LED is used for WAN
and orange LED for diag (boot/failsafe/etc.).
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
wr940nv6_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Thanks to Manuel Kock for reviewing and testing this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Manuel Kock <github.web@manu.li>
(backported from commit fbd00bb8d406a0ace7ea9c49a79cbad2418689a5)
This ports support for the TL-WA830RE v1 range extender from ar71xx to
ath79.
Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftpboot 0x80000000 \
openwrt-ath79-tiny-tplink_tl-wa830re-v1-squashfs-factory.bin
> erase 0x9f020000 +0x3c0000
> cp.b 0x80000000 0x9f020000 0x3c0000
> bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image
The device seems to be a clone of the following devices not yet
added to ath79:
- tl-wa701nd-v1
- tl-wa730re-v1
- tl-wa801nd-v1
- tl-wa901nd-v1
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
[make use of ar7240_tplink.dtsi, add note about clones]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit fb99ac6807f29eb5fe50271eff711e7415038731)
Tobias Welz