Samba could also be usefull for sending commands to windows pc (like shoutdown command). This new package add the bin to include this kind of command to the samba package.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This commit adds support for Xiaomi Mi WiFi Router 3G.
Short specification:
- MT7621AT + MT7603EN + 7612EN
- 256MB DDR3 RAM
- 128MB NAND flash
- 1+2 x 1000M Ethernet
- 1x USB 3.0 port
- reset button
- yellow, blue, red leds
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: mtd erase kernel0
- run: reboot
Originally stock firmware has following partitions:
- ...
- kernel0 (primary kernel image)
- kernel1 (secondary kernel image, used by u-boot in failsafe routine)
- rootfs0 (primary rootfs)
- rootfs1 (secondary rootfs in case primary fails)
- overlay (used as ubi overlay)
This commit squashes rootfs0, rootfs1 and overlay partitions into 1, so
it can be used by LEDE fully for package installation, resulting in 117,5MiB.
This device lacks hw watchdog, so adding softdog instead (stock does the same).
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Commit e505f59bd9 "utils/util-linux: Update to 2.30.1" bumped util-linux
without properly adjusting the dependencies of all applets.
Add missing ncursesw dependencies to sfdisk and dmesg applets to fix
packaging issues.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
c1a03e8 nl80211: request split information about frequencies
5638567 nl80211: store info about freq being not available for some bandwidths
ce51cb8 Allow storing more info about each frequency
5c10efa nl80211: support receiving split frequencies
335967c nl80211: improve error handling
ab089dd nl80211: propagate netlink errors to callers
7bba117 nl80211: handle netlink errors in nl80211_wait()
d22c64c iwinfo: add device id for Ubiquiti NanoStation Loco M2
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Revert this commit as it introduces a patchfile at a wrong location.
Since the patch was never effective, we can assume that this particular
commit was not properly tested.
This reverts commit dde9da46c1.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fix memory leak on nvram_open() and nvram_open_rdonly().
For nvram_open(), the 'fd' should be closed on error, and
mmap_area should be unmap when nvram magic can not be found.
For nvram_open_rdonly(), the 'file' variable should free before
return. Once nvram_find_mtd() return successfully, it will allocate
memory to save mtd device string.
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
get platform_data from gpio_keys_button_dev.pdata, and fix a illegal pointer
dereference like this:
[ 51.143776] gpio-keys-polled gpio-keys-polled: missing poll_interval value
[ 51.150852] gpio-keys-polled: probe of gpio-keys-polled failed with error -22
[ 828.159993] gpio-keys-polled gpio-keys-polled: no memory for button data
[ 828.166821] gpio-keys-polled: probe of gpio-keys-polled failed with error -12
Signed-off-by: Furong Xu <xfr@outlook.com>
Backing up the current firmware from U-Boot over serial can take hours.
Booting a working Linux image for backup purposes is not always an option.
Using the tftpput command in U-Boot is the fastest and easiest way.
tftpput will upload the contents of a memory region to the TFTP server.
The IP address of the server is stored in the serverip variable.
Usage:
tftpput <memaddr> <length> <filename>
Example for a complete flash backup of an o2 Box 6431 (VGV7510KW22):
VGV7510KW22 # tftpput 0xB0000000 0x1000000 o2boxbackup.bin
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
The Gateworks System Controller (GSC) mimics a standard AD7418 device on
I2C bus 0 at slave 0x29.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refresh patches.
Adapt 704-phy-no-genphy-soft-reset.patch.
Remove brcm2708/950-0005-mm-Remove-the-PFN-busy-warning.patch.
Compile-tested on brcm2708/bcm2708 and x86/64.
Runtime-tested on brcm2708/bcm2708 and x86/64.
Fixes the following vulnerabilities:
- CVE-2017-7533
- CVE-2017-1000111
- CVE-2017-1000112
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
94e65ee ndp: use IPv4 address list when comparing IPv4 addresses
ff5020d dhcpv6-ia: rework reconfigure accept logic
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The VoCore2 Lite uses the same PCB as the Vocore2.
This patch moves the common VoCore2 parts into dtsi.
Removed memory node in the device tree source file.
Memory is detected automatically.
http://vocore.io/http://vonger.net/http://vonger.cn/
Specifications:
- SoC: MediaTek MT7688AN
- RAM: 64MB DDR2 EtronTech EM68B16CWQH-25H
- Flash: 8MB NOR SPI Flash GigaDevice GD25Q64CWIG
- Wireless: Built into MT7688AN with onboard IPEX connector
Firmware installation:
- VoCore2-Lite ships with firmware forked from OpenWrt.
- Installation from the bootloader is recommended.
- If using luci/sysupgrade use the -n option (do not keep settings)
original firmware uses a modified proprietary MediaTek wireless driver.
- The wireless is disabled by default in LEDE.
- If reverting to factory firmware using the bootloader is recommended.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Tested by: Noble Pepper <noblepepper@gmail.com>
By adding the ICPlus IP1001 phy driver an already set RGMII delay mode
is reset during driver load.
Set the rgmii rx delay to fix corrupt/no packages in case the WAN port
negotiates to 1000MBit.
Fixes: FS#670
Signed-off-by: Mathias Kresin <dev@kresin.me>
While debugging an issue with a client device, wpa_supplicant did not
seem to log anything at all. Make wpa_supplicant log to syslog instead
of stdout, to make debugging easier and to be consistent with hostapd.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update (lib)expat to 2.2.3
Remove poor entropy hack, 2.2.3 uses /dev/urandom in worst case
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
USB doesn't work in some danube boards because otg_cap
is missing since previous changes made on the USB-dwc2
lantiq driver. Fix it.
Tested on the ARV7518PW router.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
With failsafe disabled there is no point in early network setup. We
don't send announcement over UDP and there is no way to ssh to the
device.
A side effect of this is avoiding a possibly incorrect network config
(only with failsafe disabled). This problem is related to possible
changes made by user in /etc/config/network.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
By default the wlan eprom contains the generic ralink MAC which is not
the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses
are decremented from the ethernet MAC.
This patch fixes the MAC address for wlan2g in line with OFW.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
If xfer_mode is set to auto the vdsl_cpe_control daemon assumes that
ATM should be used for ADSL and PTM for VDSL.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
If xfer_mode is set to auto the vdsl_cpe_control daemon assumes that
ATM should be used for ADSL and PTM for VDSL.
xfer_mode and line_mode can be set to fixed value independantly from
each other.
The syntax for the tc_layer argument of vdsl_cpe_control is as follow:
-T<TcADSL>:<TcCfgUsADSL>:<TcCfgDsADSL>_<TcVDSL>:<TcCfgUsVDSL>:<TcCfgDsVDSL>
where TcADSL and TcVDSL can be: 1=ATM, 2=PTM/EFM, 4=Auto TC-Layer
and TcCfgUsADSL, TcCfgUsVDSL, TcCfgDsADSL, TcCfgDsVDSL can be:
1=64/65-octet encapsulation supported
2=64/65-octet encapsulation with pre-emption
3=64/65-octet encapsulation with short packets
Default: In case of no '-T' option is given, ADSL will be configured
in ATM and VDSL in PTM/EFM: -T1:0x1:0x1_2:0x1:0x1
The '-M' argument of dsl_cpe_control defines the initial DSL mode
(NextMode) for ADSL/VDSL multimode handling.
Possible Values: 0=API-default, 1=ADSL, 2=VDSL
Default: In case of no '-M' option is given, '0' (API-default) will
be selected.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Philip Prindeville