This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change
is based on 3b15eb0 which added support for the wAP 2nD. This change lacks
LED support.
Specifications:
- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9531, 802.11b/g/n 2x2:2
- Ethernet: 1x100Mbps
- Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack
- SIM card slot
- Mini-PCIe slot
Installation:
1. Login to the Mikrotik WebUI to backup your licence key
2. Change the following settings in System->Routerboard->Settings:
- Boot device: try ethernet once then NAND
- Boot protocol: DHCP
- Force Backup Booter: checked
3. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image, e.g.
openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
4. Power off the device
5. If this is the second attempt to boot OpenWRT or the boot device isn't
"try ethernet once then NAND," press and hold the reset button while
powered off. If this is the first attempt, this step isn't necessary.
6. Power on the device, holding the reset button for 15-20s if already
pressed from the previous step.
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started OpenWRT via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT.
Revert to RouterOS
Use the "rbcfg" package on in OpenWRT:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: David Ehrmann <ehrmann@gmail.com>
commit e15c63a375
ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)
changed the existing rb-nor-flash-16M-ac image in a way that it would
now only support the rb-wapg-5hact2hnd.
The board show however rather be added to the existing boards in the
rb-nor-flash-16M image template.
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:
https://mikrotik.com/product/RB911-2Hnhttps://mikrotik.com/product/RB911-5Hn
The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.
Specifications:
* SoC: Atheros AR9344 (600MHz)
* RAM: 64MiB
* Storage: 16 MiB SPI NOR flash
* Ethernet: 1x100M (Passive PoE in)
* Wireless: AR9344 built-in wireless MAC, single chain
802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)
Notes:
* Older versions of these boards might be equipped with a NAND
flash chip instead of the SPI NOR device. Those boards are not
supported (yet).
* The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
same hardware. Support for that can be added later with little
effort probably.
Installation:
1. Setup a DHCP/BOOTP Server with the following parameters:
* DHCP-Option 66 (TFTP server name): pointing to a local TFTP
server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
of the to be booted image. The usable intramfs files are:
- openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
- openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
- openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin
2. Press the reset button on the board and keep that pressed.
3. Connect the board to your local network via its ethernet port.
4. Release the button after the LEDs on the board are turned off.
Now the board should load and start the initramfs image from
the TFTP server.
5. Upload the sysupgrade image to the board with scp:
$ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin
5. Log in to the running system listening on 192.168.1.1 via ssh
as root (without password):
$ ssh root@192.168.1.1
7. Flash the uploaded firmware file from the ssh session via the
sysupgrade command:
root@OpenWrt:~# sysupgrade /tmp/fw.bin
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.
See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9556
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless:
· Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
· Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
- Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive
PoE in
Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio
- Reset button
Not working:
- LEDs (added according to Mikrotik's GPL sources but not functional)
Unsupported:
- ZT2046Q SPI temperature and voltage sensor
Contributors: Giuseppe Tipaldi (@Ciusss89)
Ricky (@rickydee)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2
(mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac
wireless router. Additionally, it adds a new profile for devices with
>= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget.
See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9822 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
- SFP: 1x host
Working:
- Board/system detection
- NAND storage detection
- Wireless
- Ethernet
- 1x user LED
- Reset button
- Sysupgrade
Untested:
- SFP cage (probably not working)
Installation:
- Boot initramfs image via TFTP and then flash sysupgrade image
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for the MikroTik RouterBOARD mAP 2nD
https://mikrotik.com/product/RBmAP2nD
Specifications:
- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2)
- USB: microUSB type AB port
This patch adds missing code to fully support mAP. Machfile already
contained configuration for mAP 2nD, but device specific configuration
like LEDs etc., was missing.
Note: The POE LED works but doesn't turn on when POE passthrough is
enabled, despite being configured with GPIO trigger.
Installation
1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch adds support for the MikroTik RouterBOARD wAP
https://mikrotik.com/product/RBwAP2nD
Specifications:
- SoC: Qualcomm QCA9533 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9533, 2x2:2
- Ethernet: 1x100M (802.3af/at POE in)
This patch adds missing code to fully support wAP. Machfile already
contained configuration for wAP 2nD but device specific configuration
like LEDs etc. was missing.
Installation:
1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 4 PoE out)
- Outdoor use ready
This ethernet router is based on the same platform as the hEX PoE lite.
Installation
1. login to the Mikrotik WebUI to backup your licence keys
2. setup a DHCP/BOOTP Server with:
* DHCP-Option 66 (TFTP server name) pointing to a local TFTP
Server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. connect the port labled internet to your local network
4. keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
Server. Login as root/without password to the started LEDE via ssh
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
* rbcfg set boot_protocol bootp
* rbcfg set boot_device ethnand
* rbcfg apply
Open Netinstall and reboot routerboard. Now netinstall sees routerboard
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch adds initial support for the MikroTik RouterBOARD hAP ac
(RB962UiGS-5HacT2HnT).
All functions are supported except:
-SFP cage (eth1) is not working
-WLAN LEDs are not working
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This patch adds support for the MikroTik RouterBOARD hAP ac lite
(RB952Ui-5ac2nD).
The hAP ac lite is nearly identical to the hAP, with an added QCA9887
5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This patch enables mtdsplit for the MikroTik subtarget.
It converts mach-rbspi.c to use a single "firmware" partition.
Finally, it converts the SPI NOR profile to metadata images:
the original combined-image format is gone, the images are now
"standard" sysupgrade images with metadata appended.
Note: kernel2minor apparently pads the kernel container to erase-block
boundary, but this is undocumented behaviour, so we do not rely on it
and call pad-to anyway.
Note: in platform.sh, the boards are tested last in platform_check_image()
as this should eventually become the "*)" default case when more devices
switch to metadata images.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch implements support for the hAP lite in mach-rbspi.c
hAP lite was supported via mach-rb941.c, so this file is removed
as well as the corresponding build bits.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch adds support for the MikroTik RouterBOARD mAP lite
https://routerboard.com/RBmAPL-2nD
Specifications:
- SoC: Qualcomm QCA9533 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9533, 2x2:2
- Ethernet: 1x100M
This is another 16M SPI NOR mikrotik device. The machine file is named
mach-rbspi.c because I plan to add support for several of the other spi-based
RouterBOARD devices in subsequent patches: they share most of the hardware
and thus the same codebase.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Add full support for Mikrotik RB-941-2nD (hAP lite)
Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove the wget2nand script, drop the need for manual installation,
use sysupgrade instead.
There are now two different NAND images, one for 64 MiB flashes, the
other for >= 128 MiB
Signed-off-by: Felix Fietkau <nbd@nbd.name>
David Ehrmann