RADIUS accounting can be used even when RADIUS authentication is not
used. Move the accounting configuration outside of the EAP-exclusive
sections.
Signed-off-by: Petko Bordjukov <bordjukov@gmail.com>
This allows building images for selected devices with brcmfmac only
(without b43 which is for SoftMAC devices).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The pi_* variables and the fs_failsafe_wait_timeout variable are set by
the CONFIG_TARGET_PREINIT_* config options. No need to maintain the same
values twice.
All other fs_ variables were never used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the missing carrier status set, the interface wasn't usable on a
BTHOMEHUB2B after ip link down and up as it is done in preinit.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the author of the cpu temp driver, not all xrx200 boards
have a cpu temperature sensor. For that reason enable the sensor only
for tested boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not set the lan mac address for boards which having the lan mac
address already set in device tree source file.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The device tree binding and the associated code duplicates functionality
already patched into the etop driver. The compatible string isn't used
any more. Therefore the whole code can be dropped.
The "mac-increment" property allowed to increment a mac address received
via kernel cmdline. This functionality isn't used by any device and
should be added as etop driver device tree property if required again.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the generic mtd-mac-address dts property to get a mac address from
flash instead of the lantiq specific one.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the same mac address increment in device tree source file and
userspace.
Don't add a mac address increment to either the only mtd mac-address or
to all mac-addresses.
Fix a typo in the TDW89X0.dtsi file to add an increment.
Signed-off-by: Mathias Kresin <dev@kresin.me>
All device tree nodes are using the named properties now and the code
path handling the reg property isn't required any more.
The code related to the ath,eep-flash property has been reformatted to
be better readable.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The conversion to the new image building code accidentally caused the kernel
image to get compressed twice, leading to boot failures when kernel and rootfs
are flashed separately.
The sysupgrade images have been unaffected by this. Also restore the elf
kernel build artifact while we're at it.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Change the error message about missing SSL support to be more explicit by
mentioning required package names.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Since the only difference between 24Kec and 24Kc is the addition of DSP
ASE support, and we don't use it anymore, there is no need to keep 24Kec
as a separate cpu type.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Changes include:
* Higher maximum transmit power in the 5170-5250 band of the BG
regdomain
* Introduction of the CU regdomain
* Introduction of the 5725-5875 band (short-range devices) in the DE
regdomain
* Introduction of 60 GHz channels 1-4 in the KR regdomain
* Introduction of the 5725-5875 band (short-range devices) in the NL
regdomain
Signed-off-by: Petko Bordjukov <bordjukov@gmail.com>
sysupgrade immediately reboots after flashing an image and doesn't
allow to unmount filesystems. At least in case the image used for
sysupgrade is stored on a FAT formatted usb flash drive, the following
warning is printed during the next mount of the flash drive:
FAT-fs (sda1): Volume was not properly unmounted. Some data may be
corrupt. Please run fsck.
Although a data corruption during read operations is unlikely, there is
no need to scare the users.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move the copyright printing code to the usage printing function, to
reduce noise from regular execution but preserve information about
the author.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
/etc/init.d/boot tried to create /dev/root based on the kernel's
cmdline which won't work on any recent targets. Remove that code now
that fstools can detect the mounted rootfs based on
/proc/self/mountinfo and /dev/root was long gone anyway.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Targets that need switch drivers should select them in their kernel
config. This prevents some bloat from creeping into targets that don't
need switchdev/dsa
Signed-off-by: Felix Fietkau <nbd@nbd.name>
CPU frequency scaling enables the operating system to scale the CPU
frequency up or down in order to save power. CPU frequencies can be
scaled automatically depending on the system load, in response to ACPI
events, or manually by userspace programs.
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Petko Bordjukov