Creates /etc/device_info which will be used to fill in information for
WPS and other protocols that need manufacturer/device information
This helps with creating OpenWrt firmware for OEM or rebranded devices.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 41884
This change introduces support for wildcard patterns in "option path"
of section "wifi-device".
Objective is to allow paths like "*/usb[0-9]/*/*" in order to claim
any usb device using the same backend type, regardless of its bus
address or phy name.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41873
This patch brings full dynamic vlan support to netifd that existed in hostapd.sh in Attitude Adjustment.
Signed-off-by: Joseph CG Walker <Joe@ChubbyPenguin.net>
[jow@openwrt.org: changed commit message, rebased on top of current hostapd.sh]
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41872
Fix a typo: gpio 21 is already used for the WPS led. Gpio 20 is the
right one (tested) for the mode switch. Confirmed that
/sys/kernel/debug/gpio state followed the position of the switch.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41858
Since kernel commit 928bea964827 ("PCI: Delay enabling bridges until
they're needed"), pci fixups are run with bridges (e.g. the pcie port)
disabled.
This causses hangs when ath9k_pci_fixup tries to manually enable the
device to apply the register fixups.
Fix this by enabling any parent bridges before trying to access the
device itself.
Fixes boot on DSL-274XB rev F1.
Reported-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41856
This patch adds support for the Kingston Mobilelite Wireless (MLW-221)
http://wiki.openwrt.org/toh/kingston/mlw221
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 41841
Compile tested all subtargets and profiles.
Unfortunately I don't own any board affected by these changes, so no run tests.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41839
The earlier r41797 change was missing this part, to enable the right
vlan configuration.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41838
Since the earlier r41797 change, the board_name for awm003 has been
miscalculated, and sysupgrade has been broken. This seems to fix it.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41837
It doesn't seem to be used anywhere, it's incompatible with other
targets and can be confusing. People may think they need to update
section name every time they change VLAN ID (well, even I was doing
that).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41835
If the iface to scan on already is in ad-hoc, station or monitor mode
then do not spawn a temporary iface.
Also preventively disable IPv6 on temporary ifaces before bringing them
up to avoid potential security issues.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41830
So far iwinfo aborted a wifi scan attempt if the mac of the spawned
interface could not be changed. Change the code to try anyway - this
should fix wifi scanning on RaLink devices.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41826
Felix Fietkau