Add or fix the physical port number of switch ports to allow LuCI to
display the ports in physical order.
Remove the physical port number in case bridge port and physical port
order are the same.
Reorder the ucidef_add_switch parameter to be aligned with the switch
port number.
Remove board settings which are covered by the default case and remove
comments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
As usual these patches were extracted and rebased from the raspberry pi repo:
https://github.com/raspberrypi/linux/tree/rpi-4.4.y
Also adds support for Raspberry Pi Compute Module 3 (untested).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Permit users of the full variant to disable the NO_ID *.bind pseudo
domain masking.
Defaulted 'on' in all variants.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
As security precaution and to limit the attack surface based on
the version reported by tools like nmap mask out the dropbear
version so the version is not visible anymore by snooping on the
wire. Version is still visible by 'dropbear -V'
Based on a patch by Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove trailing _]
commit a2386c384d requires the
module to be static in the kernel.
So lets actually add support for it inside the kernel config.
Tested on Ventana
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Now that all seama images are using the new build code this seama recipe
used with the old build code can be dropped.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the blocksize for devices having only 4MB of flash for ramips
devices already using the new image build code.
Informations about the used flash chip are gathered from the OpenWrt
wiki, wikidevi, forums, OEM bootlogs or the compatible property in the
device tree source file.
The en25q32b from the AirLive Air3GII does not have 4k support in the
kernel.
For the following boards no information about the used flash chip could
be found and a 64k blocksize is assumed:
- Ralink V11ST-FE
- Ralink AP-RT3052-V22RW-2X2
- MediaTek MT7628 EVB
- MediaTek MT7621 EVB
- UPVEL UR-326N4G
- Buffalo WZR-AGL300NH
Signed-off-by: Mathias Kresin <dev@kresin.me>
At the moment the padding steps are hardcoded. Especially images for
devices with a 4K sector size can be unnecessarily bloated using the
hardcoded padding steps.
It has been observed that 192Kb of padding was added to the image of a
4MB device, albeit due to the 4K sector size the minimum required extra
padding for the jffs2 rootfs_data is 20Kb.
In worst case it means that the image-size check could fail albeit
there is enough space for all selected packages
For device build code not exposing the blocksize, use the hardcoded
padding further on.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Allows to use the same unit for all definitions of the blocksize to be
consistent regardless of the used filesystem.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Some devices (e.g. Tenda AC9 based on BCM47189B0) have BCM53125 with
port 5 connected to the second Ethernet interface on the SoC. In such
case there is no PHY and we need to force link manually.
This assumes port 5 can be marked as enabled for such devices. It's not
implemented yet unfortunately.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Don't expose dnsmasq version & other data to clients via the *.bind
pseudo domain. This uses a new 'NO_ID' compile time option which has been
discussed and submitted upstream.
This is an alternate to replacing version with 'unknown' which affects
the version reported to syslog and 'dnsmasq --version'
Run time tested with & without NO_ID on Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Mathias Kresin