Using a version number of 16 character causes a buffer overflow in the
version number overwriting the first bit of the signature in the
mkdapimg2 tool.
I am not sure if the version number should be null terminated or not.
This patch reduces the size of the version number by removing the number
of private commits from it.
This was the original version number which caused problems:
OpenWrt-r6727+10
Now it uses this version number:
OpenWrt-r6727
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Wifi button for WNDR3700 dual band routers has been renamed to "rfkill"
and its emitted keycode changed to KEY_RFKILL. This allows OpenWrt/LEDE
to support it 'out of the box' without additional tweaking.
Until this patch, button had been sending BTN_2 keycode which was
ignored by default (no action script present). To get expected behaviour
of switching radios on and off, user had to manually rename/link
'rfkill' script to name 'BTN_2' in /etc/rc.button directory.
This patch follows similar changes for other Netgear ar71xx routers,
for example WNR2000v3. It applies cleanly to both latest trunk and 17.01
branch. Tested on WNDR3700v1.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Refreshed all patches
Added new ARM64 symbol: ARM64_ERRATUM_1024718
Compile-tested on: ar71xx
Runtime-tested on: ar71xx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Fix ART offset (make it universal for 8/16 MB versions of the board) and
while at it, include also GPIO setup for h/w watchdog (EM6324QYSP5B).
Fixes: FS#1532
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
Not working:
- USB port
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
Kernel support already present.
Patch adds userspace for the 'iLS' suffix model of the RB2011 family.
Enables correct initial switch settings, sysupgrade, etc.
https://mikrotik.com/product/RB2011iLS-IN
Signed-off-by: Simon Paterson <simon.paterson.nz@gmail.com>
Some Ubiquiti U-boot versions, in particular the "U-Boot 1.1.4.2-s956
(Jun 10 2015 - 10:54:50)" found with AirOS 5.6, do not correctly flush the
caches for the whole kernel address range after decompressing the kernel
image, leading to hard to debug boot failures, depending on kernel version
and configuration.
As a workaround, prepend the relocate-kernels loader, which will invalidate
the caches after moving the kernel to the correct load address.
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Previously, tplink_pharos_check_image() would accept any image with ELF
magic and only non-printable data in the support-list, as in this case the
while-read loop would not run at all. Add the new support-list offset and
ensure an image is only accepted when the model string is actually found.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some Airmax devices can establish a Gigabit link even though the MAC only
supports 10/100 MBit/s, leading to broken connectivity. Prevent this from
happening by limiting the speed to 100MBit/s.
Fixes: FS#296
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
TP-Link Archer C60 v2 is a dual-band AC1350 router, based on
Qualcomm/Atheros QCA9561 + QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (web):
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use
OEM System Tools - Firmware Upgrade site.
Flash instruction (recovery):
1. Set PC to fixed IP address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and
rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
Flash instruction (under U-Boot, using UART):
tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Add support for TL-WR940N v6 board. It is pretty much the same as v5
except they only left WAN LED and removed other ones.
Installation: flash factory image through WEB UI or use TFTP.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rework (again) platform support for dual-role chipidea USB controller:
- include support for QCA9531
- use correct EHCI block size
- drop ar933x_usb_setup_ctrl_config() function
- simplify code after previous "register chipidea only in device mode"
change (fa22714181)
Reworked patch was tested on devices with below QCA WiSOCs (signal/GPIO
name with required bootstrap state for USB bus 0 in device mode):
- AR9331 (GPIO13 pull-down)
- AR9342 (RGMII_TXD1/ETXD1 pull-up)
- AR9344 (GPIO20 pull-up)
- QCA9531 (GPIO13 pull-up)
- QCA9558 (GPIO13 pull-up)
The only way to select device mode for bus 0 is to change SOC bootstrap
configuration which is sampled only once, at hard reset. Likely, other
models, like QCA9556 or AR9341, should also support dual-role USB mode
but they were not tested.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit adds correct model detection for UniFi
AC-Mesh. Previously said device was incorrectly detected
as UniFi AC-Lite.
The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
D-Link DAP-1330 rev. A1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR1)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 6x LED (2 are bi-color), 2x button
- 4 pin on pcb (looking from eth port and from left to right tx,rx,gnd,vcc)
Flash instruction: use "factory" image directly in vendor GUI.
This device has a recovery system that assign the ip addr of env
variable "serverip" via dhcp to a pc, and the "ipaddr" value to itself.
The recovery it's triggered by a not bootable firmware,
or pressing the reset button during the bootloader startup (first 30 seconds).
The recovery uses a http page to restore the firmware, and it's checking
the firmware image header, so use the "factory" image to
restore or the original firmware.
You can access vendor firmware over serial using:
- login: root
- password: linuxrocks
Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
It was wrong from the beginning and the trigger for the wan led was
never set due to the typo.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Only register the chipidea usb device if the strapping option indicates
device mode. If not, use the regular ehci platform driver.
Add qca955x device mode support, tested on 8devices Rambutan.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This bumps the 4.4. kernel in master to 4.4.119.
Includes more Meltdown & Spectre mitigation.
* Refresh patches.
* Refresh x86/config for RETPOLINE.
* Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream)
* Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream)
* Deleted 650-pppoe_header_pad.patch (does not apply anymore (code was replaced)).
Bumps from 4.4.112 to 4.4.115 were handled by Kevin Darbyshire-Bryant.
Compile-tested on: ar71xx & oxnas.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
With this change, the timestamp variable is only used in ag71xx_check_dma_stuck. Small tx speedup.
Based on a Qualcomm commit. ag->timestamp = jiffies was not replaced with netif_trans_update(dev) because of this quote:
It should be noted that after this series several instances
of netif_trans_update() are useless (if they occur in
.ndo_start_xmit and driver doesn't set LLTX flag -- stack already
did an update).
From: http://lists.openwall.net/netdev/2016/05/03/87
Signed-off-by: Rosen Penev <rosenp@gmail.com>
GainStrong Oolite V5.2 is a small (39.5 x 78 mm), dual-band system on
module, based on Qualcomm QCA9531 + QCA9887. All QCA9531 SOC GPIOs are
available on castellated pins.
Specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet (all ports available on castellated pins)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887) with ext. FEM (SKY85710-11)
- 3x U.FL
- 1x USB 2.0
The dedicated development board includes 5 FE ports, USB 2.0 port, two
buttons (one directly connected to SOC reset input), header with all
GPIOs and several LEDs.
Flash instruction:
Vendor firmware is based on OpenWrt. LuCI or sysupgrade can be used to
flash OpenWrt firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
- combine support for Oolite/MiniBox V1.0 in single mach-*.c file
- fix model/board names
- include correct/full vendor name
- drop redundant package and factory image
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This adds support for AR9331 based Hak5 penetration testing tools:
- WiFi Pineapple NANO
- LAN Turtle
- Packet Squirrel
WiFi Pineapple NANO specifications:
- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: 1T1R AR9331 (built-in), 1T1R AR9271 (built-in via USB bus)
- Ethernet: 1x FE over USB (ASIX AX88772A)
- Ports: 2x RP-SMA for antennas, 1x USB 2.0 (host), 1x micro SD
- Power: USB 5 V, 1.5 A
- Other: status LED, reset button
LAN Turtle specifications:
- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 1x FE (AR9331), 1x FE over USB (Realtek RTL8152B)
- Ports: 1x RJ45, version dependent: micro SD or 3G SIM slot
- Power: USB 5 V, 0.5 A
- Other: status LED, reset button (inside, on PCB)
Packet Squirrel specifications:
- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 2x FE (AR9331)
- Ports: 2x RJ45, 1x USB 2.0
- Power: USB 5 V, 0.12 A
- Other: status LED, reset button, 4-way switch
Flash instructions for all 3 devices:
Original firmware is based on OpenWrt.
Use sysupgrade via SSH to flash.
Signed-off-by: Sebastian Kinne <contact@sebkinne.com>
[squashed commits, combined and reworked mach files, aligned board
naming with general convention, fixed minor issues, tested on real
hardware, reworded commit subject and description]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Some NBG6716 do not have ath10k calibration data in flash, only in chip
OTP. To determine if flash has a valid calibration data, the first two
bytes telling the length of the calibration data are checked against the
requested length. If the lengths match, calibration data is valid and
read from flash.
Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
Vendor released new model (AP80Q) which is identical from hardware point
of view with already supported AP90Q. Include AP80Q in machine name.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore T830 is a simple N300 router with 5-port FE switch, detachable
antennas and USB 2.0 port.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531), with ext. PA (SKY65174-21) and LNA
- two external, detachable antennas (RP-SMA)
- 1x USB 2.0
- 8x LED (7 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART and JTAG headers on PCB
Flash instruction:
1. First, gain root access to the device, following below steps:
- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to "Advanced" -> "Management" -> "System" and download backup of
configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update "shadow" file and change
hash of root password to something known.
- Repack the archive, rename it back to "bakfile.bin" and use to
restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.
2. Then, install OpenWrt:
- Login over SSH and issue command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload "sysupgrade" image and install it (only if previous command
succeeded) with command: "sysupgrade -n -F openwrt-...".
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless
hub, dedicated for Samsung Shape Wireless Audio System. The device is
based on Atheros AR9344. FCC ID: A3LWAM250.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet
- 2T2R 2.4/5 GHz (AR9344), with ext. PA (SE2598L, SE5003L) and LNA
- 1x USB 2.0
- 4x LED (all are driven by GPIO)
- 2x button (reset, wps/speaker add)
- DC jack for main power input (14 V)
- UART header on PCB (J4, RX: 3, TX: 5)
Flash instruction:
This device uses dual-image (switched between upgrades) with a common
jffs2 config partition. Fortunately, there is a way to disable this mode
so that more flash space can be used by OpenWrt image.
You can easily access this device over telnet, using root/root
credentials (the same also work for serial console access).
1. Make sure that your device uses second (bootpart=2) image using
command: "fw_printenv bootpart".
2. If your device uses first image (bootpart=1), perform upgrade to the
latest vendor firmware (after the update, device should boot from
second partition) using web gui (default login: admin/1234567890).
3. Rename "sysupgrade" image to "firmware.bin", download it (you can use
wget, tftp or ftpget) to "/tmp" and issue below commands:
mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}')
mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin)
fw_setenv bootpart
fw_setenv bootcmd "bootm 0x9f070000"
reboot
Revert to vendor firmware instruction:
1. Download vendor firmware to "/tmp" device and issue below commands:
fw_setenv bootpart 1
sysupgrade -n -F SS_BHUB_v2.2.05.bin
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E385AC is an AC2200 ceiling mount AP with PoE support, based
on Qualcomm/Atheros QCA9558 + QCA9984 + QCA8337N.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 256 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet, with PoE support
- 3T3R 2.4 GHz (QCA9558), with external LNA and PA (SE2576L)
- 4T4R 5 GHz (QCA9984), with external FEM (SKY85728-11)
- 7x internal antennas
- 1x RGB LED (driven by GPIO)
- 1x button (reset)
- UART, LEDs/GPIO and USB headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
There are now supported two versions of the CF-E355AC board which differ
in 802.11ac radio chip. Include version number in board, model, image
filename, etc., also for the v1.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9886.
Short specification:
- 2x 10/100 Mbps Ethernet, with PoE support
- 128MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a, WAVE 2
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[updated kernel config for both boards]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Hauke Mehrtens