ar71xx: Add support for D-Link DAP-1330 a1

D-Link DAP-1330 rev. A1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR1)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 6x LED (2 are bi-color), 2x button
- 4 pin on pcb (looking from eth port and from left to right tx,rx,gnd,vcc)

Flash instruction: use "factory" image directly in vendor GUI.

This device has a recovery system that assign the ip addr of env
variable "serverip" via dhcp to a pc, and the "ipaddr" value to itself.
The recovery it's triggered by a not bootable firmware,
or pressing the reset button during the bootloader startup (first 30 seconds).
The recovery uses a http page to restore the firmware, and it's checking
the firmware image header, so use the "factory" image to
restore or the original firmware.

You can access vendor firmware over serial using:
- login: root
- password: linuxrocks

Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.

Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
master
Nicolò Veronese 8 years ago committed by Matthias Schiffer
parent 0d8a0a6a17
commit d265a8f2ca
No known key found for this signature in database
GPG Key ID: 16EF3F64CB201D9C
  1. 7
      target/linux/ar71xx/base-files/etc/board.d/01_leds
  2. 1
      target/linux/ar71xx/base-files/etc/diag.sh
  3. 3
      target/linux/ar71xx/base-files/lib/ar71xx.sh
  4. 1
      target/linux/ar71xx/base-files/lib/upgrade/platform.sh
  5. 1
      target/linux/ar71xx/config-4.4
  6. 1
      target/linux/ar71xx/config-4.9
  7. 9
      target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
  8. 1
      target/linux/ar71xx/files/arch/mips/ath79/Makefile
  9. 146
      target/linux/ar71xx/files/arch/mips/ath79/mach-dap-1330-a1.c
  10. 1
      target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
  11. 1
      target/linux/ar71xx/generic/config-default
  12. 22
      target/linux/ar71xx/image/generic.mk

@ -298,6 +298,13 @@ fritz300e)
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "$board:green:rssi3" "wlan0" "60" "100"
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$board:green:rssi4" "wlan0" "80" "100"
;;
dap-1330-a1)
ucidef_set_rssimon "wlan0" "2000000" "2"
ucidef_set_led_rssi "wifi-low" "wifi-low" "d-link:red:wifi" "wlan0" "1" "29"
ucidef_set_led_rssi "wifi-medium" "wifi-medium" "d-link:green:wifi" "wlan0" "30" "100"
ucidef_set_led_rssi "wifi-high" "wifi-high" "d-link:green:signal1" "wlan0" "50" "100"
ucidef_set_led_rssi "wifi-max" "wifi-max" "d-link:green:signal2" "wlan0" "70" "100"
;;
dap-2695-a1)
ucidef_set_led_default "power" "POWER" "d-link:green:power" "1"
ucidef_set_led_default "diag" "DIAG" "d-link:red:power" "0"

@ -162,6 +162,7 @@ get_status_led() {
cr5000)
status_led="pcs:amber:power"
;;
dap-1330-a1|\
dgl-5500-a1|\
dhp-1565-a1|\
dir-505-a1|\

@ -557,6 +557,9 @@ ar71xx_board_detect() {
*"CR5000")
name="cr5000"
;;
*"DAP-1330 Rev. A1")
name="dap-1330-a1"
;;
*"DAP-2695 rev. A1")
name="dap-2695-a1"
;;

@ -219,6 +219,7 @@ platform_check_image() {
cpe505n|\
cpe830|\
cpe870|\
dap-1330-a1|\
dgl-5500-a1|\
dhp-1565-a1|\
dir-505-a1|\

@ -80,6 +80,7 @@ CONFIG_ATH79=y
# CONFIG_ATH79_MACH_CPE870 is not set
# CONFIG_ATH79_MACH_CR3000 is not set
# CONFIG_ATH79_MACH_CR5000 is not set
# CONFIG_ATH79_MACH_DAP_1330_A1 is not set
# CONFIG_ATH79_MACH_DAP_2695_A1 is not set
# CONFIG_ATH79_MACH_DB120 is not set
# CONFIG_ATH79_MACH_DGL_5500_A1 is not set

@ -78,6 +78,7 @@ CONFIG_ATH79=y
# CONFIG_ATH79_MACH_CPE870 is not set
# CONFIG_ATH79_MACH_CR3000 is not set
# CONFIG_ATH79_MACH_CR5000 is not set
# CONFIG_ATH79_MACH_DAP_1330_A1 is not set
# CONFIG_ATH79_MACH_DAP_2695_A1 is not set
# CONFIG_ATH79_MACH_DB120 is not set
# CONFIG_ATH79_MACH_DGL_5500_A1 is not set

@ -2300,6 +2300,15 @@ config ATH79_MACH_QIHOO_C301
select ATH79_DEV_USB
select ATH79_NVRAM
config ATH79_MACH_DAP_1330_A1
bool "D-Link DAP-1330 rev. A1 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_DAP_2695_A1
bool "D-Link DAP-2695 rev. A1 support"
select SOC_QCA955X

@ -89,6 +89,7 @@ obj-$(CONFIG_ATH79_MACH_CPE830) += mach-ap90q.o
obj-$(CONFIG_ATH79_MACH_CPE870) += mach-cpe870.o
obj-$(CONFIG_ATH79_MACH_CR3000) += mach-cr3000.o
obj-$(CONFIG_ATH79_MACH_CR5000) += mach-cr5000.o
obj-$(CONFIG_ATH79_MACH_DAP_1330_A1) += mach-dap-1330-a1.o
obj-$(CONFIG_ATH79_MACH_DAP_2695_A1) += mach-dap-2695-a1.o
obj-$(CONFIG_ATH79_MACH_DB120) += mach-db120.o
obj-$(CONFIG_ATH79_MACH_DGL_5500_A1) += mach-dgl-5500-a1.o

@ -0,0 +1,146 @@
/*
* D-Link DAP-1330
*
* Copyright (c) 2013-2015 The Linux Foundation. All rights reserved.
* Copyright (c) 2017 Nicolò Veronese <nicveronese@gmail.com>
* Copyright (c) 2017 Federico Cappon <dududede371@gmail.com>
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*
*/
#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <asm/mach-ath79/ath79.h>
#include <asm/mach-ath79/ar71xx_regs.h>
#include "common.h"
#include "dev-eth.h"
#include "dev-gpio-buttons.h"
#include "dev-leds-gpio.h"
#include "dev-m25p80.h"
#include "dev-wmac.h"
#include "machtypes.h"
#include "nvram.h"
#include <linux/kernel.h>
#include <linux/vmalloc.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/string.h>
#define DAP_1330_GPIO_LED_GREEN_POWER 13
#define DAP_1330_GPIO_LED_RED_POWER 3
#define DAP_1330_GPIO_LED_GREEN_WIFI 14
#define DAP_1330_GPIO_LED_RED_WIFI 11
#define DAP_1330_GPIO_LED_SIGNAL1 15
#define DAP_1330_GPIO_LED_SIGNAL2 16
#define DAP_1330_GPIO_BTN_WPS 2
#define DAP_1330_GPIO_BTN_RESET 17
#define DAP_1330_KEYS_POLL_INTERVAL 20 /* msecs */
#define DAP_1330_KEYS_DEBOUNCE_INTERVAL (3 * DAP_1330_KEYS_POLL_INTERVAL)
#define DAP1330_MAC_ADDR 0x1f020001
#define DAP1330_WMAC_CALDATA_ADDR 0x1f010000
#define DAP_1330_WMAC_CALDATA_OFFSET 0x1000
static struct gpio_led dap_1330_leds_gpio[] __initdata = {
{
.name = "d-link:green:power",
.gpio = DAP_1330_GPIO_LED_GREEN_POWER,
.active_low = 1,
},
{
.name = "d-link:red:power",
.gpio = DAP_1330_GPIO_LED_RED_POWER,
.active_low = 1,
},
{
.name = "d-link:green:wifi",
.gpio = DAP_1330_GPIO_LED_GREEN_WIFI,
.active_low = 1,
},
{
.name = "d-link:red:wifi",
.gpio = DAP_1330_GPIO_LED_RED_WIFI,
.active_low = 1,
},
{
.name = "d-link:green:signal1",
.gpio = DAP_1330_GPIO_LED_SIGNAL1,
.active_low = 1,
},
{
.name = "d-link:green:signal2",
.gpio = DAP_1330_GPIO_LED_SIGNAL2,
.active_low = 1,
}
};
static struct gpio_keys_button dap_1330_gpio_keys[] __initdata = {
{
.desc = "WPS button",
.type = EV_KEY,
.code = KEY_WPS_BUTTON,
.debounce_interval = DAP_1330_KEYS_DEBOUNCE_INTERVAL,
.gpio = DAP_1330_GPIO_BTN_WPS,
.active_low = 1,
},
{
.desc = "Reset button",
.type = EV_KEY,
.code = KEY_RESTART,
.debounce_interval = DAP_1330_KEYS_DEBOUNCE_INTERVAL,
.gpio = DAP_1330_GPIO_BTN_RESET,
.active_low = 1,
}
};
static void __init dap_1330_setup(void)
{
u8 *art = (u8 *) KSEG1ADDR(DAP1330_WMAC_CALDATA_ADDR);
u8 *mac_ptr = (u8 *) KSEG1ADDR(DAP1330_MAC_ADDR);
u8 mac[ETH_ALEN];
ath79_parse_ascii_mac((char *) mac_ptr, mac);
ath79_register_m25p80(NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(dap_1330_leds_gpio),
dap_1330_leds_gpio);
ath79_register_gpio_keys_polled(-1, DAP_1330_KEYS_POLL_INTERVAL,
ARRAY_SIZE(dap_1330_gpio_keys),
dap_1330_gpio_keys);
ath79_register_wmac(art + DAP_1330_WMAC_CALDATA_OFFSET, mac);
ath79_register_mdio(0, 0x0);
ath79_init_mac(ath79_eth1_data.mac_addr, mac, 0);
/* LAN ports */
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
ath79_eth1_data.speed = SPEED_1000;
ath79_eth1_data.duplex = DUPLEX_FULL;
ath79_switch_data.phy_poll_mask |= BIT(4);
ath79_switch_data.phy4_mii_en = 1;
ath79_register_eth(1);
}
MIPS_MACHINE(ATH79_MACH_DAP_1330_A1, "DAP-1330-A1",
"D-Link DAP-1330 Rev. A1", dap_1330_setup);

@ -78,6 +78,7 @@ enum ath79_mach_type {
ATH79_MACH_CPE870, /* YunCore CPE870 */
ATH79_MACH_CR3000, /* PowerCloud CR3000 */
ATH79_MACH_CR5000, /* PowerCloud CR5000 */
ATH79_MACH_DAP_1330_A1, /* D-Link DAP-1330 rev. A1 */
ATH79_MACH_DAP_2695_A1, /* D-Link DAP-2695 rev. A1 */
ATH79_MACH_DB120, /* Atheros DB120 reference board */
ATH79_MACH_DGL_5500_A1, /* D-link DGL-5500 rev. A1 */

@ -55,6 +55,7 @@ CONFIG_ATH79_MACH_CPE830=y
CONFIG_ATH79_MACH_CPE870=y
CONFIG_ATH79_MACH_CR3000=y
CONFIG_ATH79_MACH_CR5000=y
CONFIG_ATH79_MACH_DAP_1330_A1=y
CONFIG_ATH79_MACH_DAP_2695_A1=y
CONFIG_ATH79_MACH_DB120=y
CONFIG_ATH79_MACH_DGL_5500_A1=y

@ -32,6 +32,16 @@ define Build/mkwrggimg
mv $@.imghdr $@
endef
define Build/mkdapimg2
$(STAGING_DIR_HOST)/bin/mkdapimg2 \
-i $@ -o $@.new \
-s $(DAP_SIGNATURE) \
-v $(VERSION_DIST)-$(firstword $(subst -, ,$(REVISION))) \
-r Default \
$(if $(1),-k $(1))
mv $@.new $@
endef
define Build/netgear-squashfs
rm -rf $@.fs $@.squashfs
mkdir -p $@.fs/image
@ -1129,6 +1139,18 @@ define Device/qihoo-c301
endef
TARGET_DEVICES += qihoo-c301
define Device/dap-1330-a1
DEVICE_TITLE := D-Link DAP-1330 rev. A1
DEVICE_PACKAGES := rssileds
BOARDNAME := DAP-1330-A1
IMAGES := factory.img sysupgrade.bin
IMAGE_SIZE := 7936k
IMAGE/factory.img := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | mkdapimg2 917504
MTDPARTS := spi0.0:64k(u-boot)ro,64k(art)ro,64k(mp)ro,64k(config)ro,7936k(firmware)
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1330
endef
TARGET_DEVICES += dap-1330-a1
define Device/dap-2695-a1
DEVICE_TITLE := D-Link DAP-2695 rev. A1
DEVICE_PACKAGES := ath10k-firmware-qca988x kmod-ath10k

Loading…
Cancel
Save