OpenVPN 2.3 added a route-pre-down option, to run a command before
routes are removed upon disconnection.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
SVN-Revision: 47134
The device is similar to the TD-W8970, beside a different Atheros 2.4 GHz
wireless chip and the additional, PCI connected, WAVE300 5 GHz wireless.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47130
Port of r41856.
In contrast to the brcm63xx target, it isn't sufficient to enable/disable
the bridge. The device needs to be enabled/disabled to fix the hang. The
bridge will be automatically enabled by the time the connected device is
enabled.
Fixes boot on TD-W8980.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47129
This adds the changes from r46219 to the linux 4.1 patches as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47128
This way it's easier to configure device tree overlays, customize other
parameters...
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47126
Right now, selecting kmod-sound-soc-bcm2708-i2s causes build errors due to
missing configs.
kmod-regmap enables I2C and SPI, causing build errors due to depending
variables not defined.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47123
when sleep mode is disable use MIPS as clocksource and clockevent instead of systick.
because MIPS timer has higher resolution 5ns less than systick 20us and
larger counter bits 32 > 16.
clean interrupt by write compare register at isr.
fix typo cause sleep mode not enable.
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47122
Due to datasheet of rt3883 SoC rgmii1 port handles pins 84-95 and rgmii2 port handles pins 72-83. When this function ports gets added to rt3883_pinmux_data there's wrong pinmux bits set (RT3883_GPIO_MODE_GE1 manages 84-95 pins and RT3883_GPIO_MODE_GE2 manages 72-83). So when enabling rgmii2 as GPIO driver confuses hardware and nothing work, neither rgmii nor gpio.
Also in '0030-pinctrl-ralink-add-pinctrl-driver.patch' typo in name of rgmii2 port.
Signed-off-by: Nick Leiten <nickleiten@gmail.com>
SVN-Revision: 47118
The default switch frame size (with FCS + header) is 1536 bytes. But the
GMAC only accepted frames up to 1522 bytes. Setting it to 1536 allows to
receive ethernet frames using the full of MTU 1500 + an extra VLAN header +
VLAN header added by the switch.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47117
The driver assumes that the maximum received buffer for non-jumbo frames is
1536 bytes. But the allocation of the rx fragment doesn't reflect that. It
currently allocates fragments which will only be large enough to be used as
rx buffer with the size of 1534 bytes. This is problematic because the GMAC
will now try to write to 2 bytes which don't belong to its receive buffer
when a large enough ethernet frame is received.
This may already be a problem on existing chips but will at least become a
problem when the 1536 byte rx modus is enabled on MT7621a. It is required
on this SoC to receive ethernet frames which use their full 1500 bytes MTU
and a VLAN header next to the switch VLAN tag.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47116
The length of the DMA rx buffer was always set to 0 because the function
for extracting the length was used to calculate the value for setting it.
Instead the macro has to be split in a get and set function similar to the
TX_DMA_(GET_|)PLEN(0|1) macro.
No problem was noticed on MT7621a before this was changed and thus maybe it
was hidden by different problem which is not yet fixed.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47115
The MT7530 switch driver with enable_vlan set will automatically set all
ports to the user port mode. The hardware will remove the incoming vlan tag
on these ports and use it for its internal vlan. This is usually not wanted
and makes it impossible to communicate via vlan over the switch in both
directions.
It is possible to configure a switch port to "transparent mode" when this
port is only used as untag in the switch VLANs. This will disable the VLAN
untagging of packets when they were received on this port. The tagging on
"tag" ports based on the vlan id is still working.
The transparent port mode cannot be used when a port is both used in a VLAN
as "tag" and in another one as "untag" port.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47114
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com <http://www.hiwifi.com/>. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Spaces -> Tabs
2: Removed some packages
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47113
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Merged most stuff into dtsi file
2: Remove unnecessary empty lines.
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47112
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Fixed model order
2: Remove manufacturer name from model name
3: Use a hacky but prettier way to get mac address.
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47111
Only add 'cuImage.tl-wdr4900-v1' to KERNEL_IMAGES if
the selected subtarget is 'generic'.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47109
Overriding LD_LIBRARY_PATH for host utilities frequently leads to problems
with host executables loading shared libraries from the staging_dir, leading
to crashes due to incompatible ABIs.
Since most host utilties either embed a proper rpath or are reworked to link
statically we do not need the workaround anymore.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47103
Install header files into same location as pkgconfig/libnl-3.0.pc says:
Cflags: -I${includedir}/libnl3
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 47102
Recently all targets have been updated to call nand_do_upgrade directly.
It's not needed anymore to leave a magic /tmp/sysupgrade-nand-path mark
during image check.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47079
uClibc-ng is a spin-off of original uClibc, see http://www.uclibc-ng.org/
We try to regularly add changes from uClibc to uClibc-ng.
We even sent patches and bug reports to the uClibc mailing list.
The config file is compatible between uClibc-ng 1.0 and uClibc git master.
This might change in the future.
Our main goal is to provide regularly a stable and tested release
to make embedded system developers happy.
The main advantage of uClibc-ng over olde good uClibc is regular releases
so there's no need to keep tons of patches on top of years old
0.9.33.2
Build-tested for
[1] ARM: Sunxi generic
[2] MIPS: Netgear WNDR3600/3700/3800
Run-tested for [yet out of the tree] Synopsys Designware ARC AXS101.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Waldemar Brodkorb <wbx@uclibc-ng.org>
Cc: Mathieu Olivari <mathieu@codeaurora.org>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
SVN-Revision: 47077
Prevent quilt's build system from generating useless compat wrappers and
hardcoded absolute utility paths to binaries in staging_dir/host/.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47070
When using FullMAC drivers (e.g. brcmfmac) we don't get mgmt frames so
check for banned client in probe request handler won't ever be used.
Since cfg80211 provides us info about STA associating let's put a check
there.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47064
John Crispin