Also move it to an earlier place so new boards added are less likely
to confuse quilt.
Fixes#19965.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46148
Register buttons and leds through DT for all available dts,
and remove them from the board files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: remove leds/buttons from board files
fix wrong led polarities for dsl-274xb-c2, cpva642, p870hw
comment out spi-gpio and associated leds]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44566
Move compatible strings from board structs into separate table. This
allows for several board compatibles to match to the same board in case
e.g. only the flash size / partitions differ.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43341
Now that we migrated all users to dtb based detection, we can drop the
board fixup code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42129
Allow appending a dtb blob to the binary and use it for identifying the
board. Fall back to nvram based identification in case of no dtb passed.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42119
Rework fallback sprom support by providing different sproms for
different chips. Also make it optional to use.
This likely causes sprom fallback support to break on a few boards.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41942
Move defines and board_info structs back to their proper locations so
(de-)selecting SOC support won't break the build.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41550
Use the CFE_EPTSEAL to tell them apart at runtime. Added for now only
for the 3.14 until properly tested.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41296
Now that 3.13 will be EOL soon, switch to 3.14.
Known issues:
* 74x164 is not available because upstream dropped non-DT support
* jffs2 breaks with SMP
Unknown issues:
* probably plenty
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 40380
Add support for 3.13 as a development kernel. Mostly untested, only net
booted. If flashed may brick your router or kill your cat.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39746
Update a few devices with their actual port numbers, especially those
with two ports.
Should allow properly using the second port on the Neufboxen and HW553
and HW556.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39325
Changeset r39302 updated a board section and added twice .has_ehci0,
this is not necessary, so fix it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39304
BCM6318 has a special initialization sequence which involves touching
PLL control registers in the USBH_PRIV register space, as well as
toggling a bit the Simulation control register.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39302
Switch to using the B53 switch driver where appropriate.
Use a non-tagged default config where it isn't confirmed to be
working.
Remove the switch configuration in preinit as the switch will now
be configured by the driver to use port isolation to prevent leakage
between lan and wan.
While at it, also provide a switch config for Neufbox 6.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35307
This patch adds support for defining rt2x00 eeprom data.
This eeprom data can be extracted from flash or loaded directly from a firmware file.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 34322
Some new board definitions were added within the #ifdef CONFIG_CPU_6338
section while some other were added within #ifdef CONFIG_CPU_6345, fix this
SVN-Revision: 32060
Jonas Gorski