YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE
(802.3at) support, based on QCA9531 + QCA9887.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11)
- 2x regular LED, 1x RGB LED (all driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
1. First, gain root access to the device, following below steps:
- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to 'Advanced' -> 'Management' -> 'System' and download backup of
configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update 'shadow' file and change
hash of root password to something known.
- Repack the archive, rename it back to 'bakfile.bin' and use to
restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.
2. Then, install OpenWrt:
- Login over SSH and issue command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload 'sysupgrade' image and install it (only if previous command
succeeded) with command: 'sysupgrade -n -F openwrt-...'.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch
WLAN: 2.4/5 GHz
UART: 1 UART
LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
Flashing instructions using recovery method over TFTP
1. Unplug the ethernet cable from the router.
2. Using paper clip press and hold the router's reset button. Make sure
you can feel it depressed by the paper clip. Do not release the button
until step 4.
3. While keeping the reset button pressed in, plug the ethernet cable
back into the AP. Keep the reset button depressed until you see the
device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
LED2/LED4), this may take up to 25 seconds.
4. You may release the reset button, now the device should be in TFTP
transfer mode.
5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
should work.
6. Plug the PoE injector's LAN cable directly to your computer.
7. Start tftp client and issue following commands:
tftp> binary
tftp> connect 192.168.1.20
tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin
Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless
CPE with two Ethernet ports and a 802.11an radio.
Specifications:
- AR9344 SoC
- 535/400/267 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 5 GHz, up to 25 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new one, so a factory reset will be
needed. To do so, once the new firmware is flashed, enter into failsafe
mode by pressing the reset button several times during the boot
process, while while the WAN LED flashes, until it starts flashing
faster. Once in failsafe mode, perform a factory reset as usual.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and
keep it pressed for >10 seconds. The recovery page will be at
http://192.168.1.1
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The TP-Link WDR3600 shares the same machine-code in the ar71xx target,
thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list
metadata to allow non-forced sysupgrades from ar71xx to ath79.
With this, it is possible to flash a WDR4300 image on the WDR3600. It
is no problem however, as the only difference is the 5GHz WiFi chip
which has 3SS instead of 2SS. Both work with either image.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds the support-list entry the AVM FRITZ!Box 4020 expects in the
ar71xx target to allow non-forced sysupgrades from ar71xx to ath79.
Signed-off-by: David Bauer <mail@david-bauer.net>
I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.
Specification:
- SoC: Qualcomm Atheros QCA9557
- RAM: 128 MB
- Flash: 16 MB
- WLAN: 2.4/5 GHz
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 3T3R (QCA9880)
- Ethernet: 5x 10/100/1000 Mbps
- Switch: QCA8337N
- LED/key: 6x/6x(4x buttons, 1x slide switch)
- UART: through-hole on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Alternative flash instruction using initramfs image:
1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing
This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Hardware
--------
CPU: Qualcomm Atheros QCA9561
RAM: 64M DDR2
FLASH: 16M SPI-NOR
ETH: 1x WAN - 2x LAN
WiFi: QCA9561 3T3R
BTN: 1x Reset - 1x WPS
LED: 1x Blue - 1x Red - 1x Yellow
UART: TX - GND - RX - VCC (From ethernet port)
115200n8 - 3.3V
Installation
------------
1. Connect to the device via UART.
2. Interrupt the U-Boot on power-on by pressing enter when prompted.
3. Connect you computer to one of the routers LAN ports.
Assign yourself the IP 192.168.31.10/24.
Copy the OpenWRT initramfs image to a tftp server root directory.
Rename the image to 'x4q.bin'.
4. Load the initramfs image to the router by executing following command
in U-Boot. The image will boot afterwards.
> tftpboot 0x81000000 x4q.bin; bootm
5. SCP the sysupgrade-image into '/tmp'.
Remember to assign yourself an IP in 192.168.1.0/24 for this step!
6. Install OpenWRT permanently by executing
> sysupgrade -n /tmp/<OpenWRT-sysupgrade-image>
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the
Qualcomm/Atheros QCA9561 SoC + QCA9880.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
1x Atheros AR8033
WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3)
WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3)
BTN: 1x Reset
1x WPS
1x USB eject
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports)
Dupont 4 pin header
Rear RJ45 serial port non-functional
USB: 1x v2.0
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password previously set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Replace the code with a more readable version. Rename the recipe
to reflect the real usecase.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for the COMFAST CF-E110N, an outdoor wireless
CPE with two Ethernet ports and a 802.11bgn radio.
Specifications:
- 650/400/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 26 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new want, so a factory reset will be
needed: once the new firmware is flashed, perform the factory reset by
pushing the reset button several times during the boot process, while the
WAN LED flashes, until it starts flashing quicker.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and keep it
pressed for >10 seconds. The recovery page will be at http://192.168.1.1
Notes:
The device is advertised, sold and labeled as "CF-E110N", but the
bootloader and the stock firmware identify it as "v2".
Acknowledgments:
Petr Štetiar <ynezz@true.cz>
Sebastian Kemper <sebastian_ml@gmx.net>
Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[drop unused labels from devicetree source file]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for TP-Link Archer C6 v2 (EU)
Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board
Flash instructions:
Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
EnGenius EWS511AP is a wireless managed wall AP with PoE support,
based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887.
Short specification:
- 128MB of RAM
- 16 MB of SPI FLASH
- 2T2R 2.4 GHz (QCA9531), 802.11b/g/n
- 1T1R 5 GHz (QCA9887), 802.11ac/n/a
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED
- 1x RESET button
- built-in watchdog chipset
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
Original firmware is based on QSDK.
Use sysupgrade firmware directly in vendor GUI.
Reset to factory default is necessary.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the OpenWrt firmware in the root directory on your computer.
2. Power up EWS511AP. Press 4 and then press any key to enter u-boot.
3. Download OpenWrt firmware
(ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin"
4. Flash the firmware
(ath)> erase 0x9f060000 +f50000
(ath)> cp.b $fileaddr 0x9f060000 $filesize
5. Reboot
(ath)> reset
Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
CPU: Atheros AR9341 535MHz
RAM: 32MB
FLASH: 4MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9341 2x2:2 bgn
LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill
BTN: WPS, WiFi, Reset
Installation:
Upload the factory image via the vendor-GUI.
Signed-off-by: Antonio Silverio <menion@gmail.com>
[resolve merge conflicts, squash commits, fix commit title, remove
default default off led properties, mark sysupgrade image compatible
with the ar71xx version of the board, drop blank lines from dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Right now this patch adds nor image generation only. NAND image
generation is not supportet at the moment.
Furtheremore support for the MicroSD port is not implemented as of now.
Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)
- Another LED can be accessed on GPIO 7 if soldered
Flash instruction:
- Set static ip to 192.168.1.2
- Unplug the power cord
- Hold reset button
- Plug power back in
- Right led will flash 5 times
- Release reset button
- Browse to 192.168.1.1
- Choose sysupgrade image in NOR-flash section
- Press "update nor firmware"
- After successful transfer unplug network cable before device restarts
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[resolve merge conflicts, rename buttons, use switch input type for mode
switch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880
USB is supported on the PCB but not connected.
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or the u-boot
failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted. Otherwise the u-boot
will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the firmware
checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
upgrade the factory.bin through the u-boot failsafe interface and then goto
step 2.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
There is also a Micro-B USB-port present but this only seems to be a
dummy as the circuit next to it is not present (at least in my unit).
It is also not mentioned in the devolo manual.
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for TP-Link Archer C7 v5, leveraging most effort
from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5
but with a different flash layout.
Specification:
- QCA9563 SoC (750 MHz)
- 128 MiB of RAM (DDR2)
- 16 MiB of flash (SPI)
- 5x 1 Gbps Ethernet (1x WAN + 4x LAN)
- 2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880
- 10x LED, 2x button
- UART header on PCB
Flash instructions:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin
via web interface.
Flash instructions using TFTP recovery:
1. Plug PC to one of the LAN ports
2. Set PC to fixed IP address 192.168.0.66
3. Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in
TFTP root directory
4. Turn on the router with the reset button pressed for about 15 secs
5. Release the button and wait about 150 secs to complete flashing
Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
Atheros QCA9563.
Specification:
- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2.4/5 GHz wifi
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 1T1R (QCA9887)
- 4x 10/100/1000 Mbps Ethernet
- 8x LEDs, 3x keys (2x buttons, 1x slide-switch)
- UART through-hole on PCB (J2)
- Vcc, GND, NC, TX, RX from SoC side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port on WG800HP
2. Connect power cable to WG800HP and turn on it
3. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Use pad-offset and append-string to create the cameo factory images for
the D-LINK DIR-825 C1/DIR-835 A1 factory images.
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Since commit 61b5b4971e ("mac80211: make ath10k-ct the default ath10k")
select ath10k-ct and the -ct firmwares by default.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for TP-Link Archer A7
Specification:
- SOC: QCA9563
- Flash: 16 MiB (SPI)
- RAM: 128 MiB (DDR2)
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) SoC internal
- 5GHz (ac) QCA988x
- USB: 1x USB 2.0 port
- Button: 1x power, 1x reset, 1x wps
- LED: 10x LEDs
- UART: holes in PCB
- Vcc, GND, RX, TX from ethernet port side
- 115200n8
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin
via the Webinterface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the Archer A7
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the tftp
root directory renamed to ArcherC7v5_tp_recovery.bin
2. Connect power cable to Archer A7, press and hold the reset button
and turn the router on
3. Keep the reset button pressed for ~5 seconds
4. Wait ~150 seconds to complete flashing
Changes since first revision:
- Flash instructions using stock image webinterface
- Changed "Version 5" in model string to "v5"
- Split DTS file in qca9563_tplink_archer-x7-v5.dtsi
and qca9563_tplink_archer-a7-v5.dts
- Firmware image is now build with dynamic partitioning
- Default to ath10k-ct
Changes since second revision:
- Changed uboot@0 to uboot@20000 in DTS file
- Fixed ordering issue in board led script
- Specify firmware partition format in DTS file
- Rebased Makefile device definition on common
Device/tplink-safeloader-uimage definition
- Merged switch section in network script
(same configuration as tplink,tl-wdr3600
and tplink,tl-wdr4300)
Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79.
They're pretty much identical, except dir-835-a1 has less LEDs.
The routers come with 128 MByte of RAM and 16 MBytes of flash and sport
2.4GHz and 5.0GHz wireless. Both routers have entries already in
OpenWrt's TOH. Please check there for more information on these
antiquities.
https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1
Installation:
1. Connect to the web interface of the vendor firmware (usually
listening on 192.168.0.1).
2. Go to "Tools", then "Firmware".
3. In the "Firmware Upgrade" box click "Browse".
4. Select the OpenWrt factory image for your router.
5. Click "Upload", confirm the popups if you agree to flash the file you
selected.
6. Wait for firmware upgrade to complete. It takes about 5 minutes.
Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't
have this router so I can't confirm.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
This ports support for TP-Link TL-WR842N/ND v1 from ar71xx.
CPU: Atheros AR7241 400 MHz
RAM: 32 MiB
FLASH: 8 MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9287
LED: SYS, WiFi, LAN, WAN, 3G, QSS
BTN: WiFi, Reset/WPS
AR71xx target used "tl-mr3420" as board id so force flag is needed
if upgrading from old target.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial cleanup]
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros
AR1022.
WN-AG300DGR does not have an LED to indicates power or system status,
I set "router" LED as OpenWrt status LED.
There is no eeprom data for 5 GHz wlan in "art" partition.
Specification:
- Atheros AR1022
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4/5GHz wifi
- 2.4 GHz: SoC internal
- 5 GHz: Atheros AR93x2
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- 1x USB 2.0 Type-A
- UART through-hole on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port on WN-AG300DGR
2. Connect power cable to WN-AG300DGR and turn it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
WB2000 is a dual-band 11N AP using AR9344.
The factory firmware used the original DB120 partition table
with a small kernel partition at the end of firmware and the
kernel will easily get oversized in the future. Since it has
to be flashed using UART I also swapped kernel/rootfs and
changed the default load address.
Specification:
- SoC: Atheros AR9344
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 10/100/1000 Mbps (Atheros AR8035)
- 2x USB 2.0
- WIFI: AR9344(2G) + AR9382(5G)
- RTC: DS1338
Known issue:
5G ath9k led doesn't work due to commit ccab68f.
Flash instruction:
Set up a TFTP server on your computer and configure static IP.
Connect UART (J11 TX/GND/RX) and press any key to enter U-boot
shell.
1. Change the default boot command:
setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000'
saveenv
2. Set your router ipaddr and server ipaddr. e.g.:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.50
3. Load and flash the firmware:
tftp 0x80060000 fw.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
4. Reset your router:
reset
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Drop the i2c node unit address. Move the ath9k-leds node out of the spi
node, it doesn't belong there. Add the #gpio-cells property to the pci
wifi node. All fix dtc compiler warnings]
Signed-off-by: Mathias Kresin <dev@kresin.me>
merge
The userspace boardname derived from the dts compatible was out of sync
with the expected board added to the image metadata. This way a
sysupgrade is refused.
Sync the userspace boardname and the baordname used in the image metdata
to allow a seamless sasupgrade.
Signed-off-by: Mathias Kresin <dev@kresin.me>
qca9533 is a costdown version of qca9531 which doesn't have USB and PCIE.
Rename the misleading dtsi names and fix the SoC type of gl-ar300m.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[apply the changes for the gl-x750 as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Indoor low-power router with 2.4 GHz radio
CPU: Atheros AR7241 rev 1
RAM: 32 MB
Flash: 8 MB NOR SPI
Switch: Atheros AR7240
Ports: 1x WAN, 4x LAN 10/100 Ethernet
WLAN: Atheros AR9285 (2.4 GHz)
USB: 1x USB2 host port
Note: Ethernet WAN/LAN port naming is reversed from ar71xx.
WAN is eth0; LAN is eth1.1.
UART settings: 115200, 8N1
LEDs
+--------------------------
|
|
|
|
|
|
|
|
VCC | x x
RX | * x
| x x
| x x
TX | * x
GND | * x
|
|
|
|
+--------------------------
ETHERNET PORTS
Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices.
Signed-off-by: Russell Senior <russell@personaltelco.net>
This commit adds support for the ROSINSON WR818 WiFi-Router
SoC: Qualcomm Atheros QCA9563,
FLASH: Winbond W25Q128FV 16MBytes,
WiFi: QCA9563 b/g/n 3x3 450Mbit/s,
USB: 1x USB 2.0 Type A, 1x USB2.0 Type C,
IN: WPS/Reset button GPIO1,
OUT: Power LED red, Internet LED red, WLAN LED red,
LAN1 LED red, LAN2 LED red, System LED red,
UART: RX-GPIO18, TX-GPIO22,
Tested and working:
- Ethernet (LAN + WAN)
- WiFi
- OpenWRT sysupgrade
- Button
- LEDs
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.1.1
- Go to "Administration" -> "Firmware Upgrade"
- Upload the OpenWrt sysupgrade image
Signed-off-by: Rosy Song <rosysong@rosinson.com>
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.
In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.
0x50000 0xe80000 0xff0000
+-------------------------------+--------------+
| rootfs | kernel |
| (14528k) | (1472k) |
+-------------------------------+--------------+
After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.
0x50000 0xff0000
+----------------------------------------------+
| firmware |
| (16000k) |
+----------------------------------------------+
However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".
This commit requires new flash instruction instead of the old one.
Flash instruction using initramfs image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
/dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
fw_setenv ipaddr 192.168.12.1
fw_setenv serverip 192.168.12.10
fw_setenv ethaddr 00:aa:bb:cc:dd:ee
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing
And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit adds support for the Archer C58 v1 and C59 v1, previously
supported in the ar71xx target.
CPU: Qualcomm QCA9561
RAM: 64M (C58) / 128M (C59)
FLASH: 8M (C58) / 16M (C59)
WiFi: QCA9561 bgn 3x3:3
QCA9888 nac 2x2:2
LED: Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS
Only C59: USB
BTN: WPS, WiFi, Reset
Installation
------------
Via Web-UI:
Update factory image via Web-UI.
Via TFTP:
Rename factory image to "tp_recovery.bin" and place it in the root-dir
of your tftp server. Configure to listen on 192.168.0.66. Power up the
router while holding down the reset-button. The router will flash itself
and reboot.
Note: For TFTP, you might need a switch between router and computer, as
link establishment might take to long.
Signed-off-by: David Bauer <mail@david-bauer.net>
this patch adds supports for GL-X750.
Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 1xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 5x LEDS (green)
Flash instruction:
The original firmware is openwrt, so both LuCI or sysupgrade can be used.
Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:
All future airOS versions will be signed in this way and not allow
unsigned firmware to be loaded except via TFTP.
U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:
Hit any key to stop autoboot: 0
Setting default IP 192.168.1.20
Starting TFTP server...
Receiving file from 192.168.1.25:38438
Received 4981148 bytes
Firmware check failed! (1)
By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:
Received 3735964 bytes
Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt
Setting U-Boot environment variables
Un-Protected 1 sectors
Erasing Flash.... done
Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and
Nanostation M5 XW (ae6xe).
1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART: 1 UART on PCB marked as J1 with 115200 8N1 config
LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
UART connection details
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions
A) Serial console, U-Boot and TFTP
1. Connect to serial header J1 on the PCB
2. Power on device and enter U-Boot console
3. Set up TFTP server serving an OpenWrt initramfs build
4. Load initramfs build using the command tftpboot in the U-Boot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs OpenWrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
B) Experimental factory image flashing over SSH from airOS v6.1.7
1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware
no other airOS version is currently supported
2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing
3. cd ubnt-bullet-m2hp-openwrt-flashing
4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin
Tested only on Bullet M2HP.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Piotr Dymacz