NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - Qualcomm Atheros QCA9563 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 1T1R (QCA9887) - 4x 10/100/1000 Mbps Ethernet - 8x LEDs, 3x keys (2x buttons, 1x slide-switch) - UART through-hole on PCB (J2) - Vcc, GND, NC, TX, RX from SoC side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WG800HP 2. Connect power cable to WG800HP and turn on it 3. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>master
parent
99df98442e
commit
c566439c9b
@ -0,0 +1,188 @@ |
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
||||
/dts-v1/; |
||||
|
||||
#include <dt-bindings/gpio/gpio.h> |
||||
#include <dt-bindings/input/input.h> |
||||
|
||||
#include "qca956x.dtsi" |
||||
|
||||
/ { |
||||
model = "NEC Aterm WG800HP"; |
||||
compatible = "nec,wg800hp", "qca,qca9563"; |
||||
|
||||
chosen { |
||||
bootargs = "console=ttyS0,115200n8"; |
||||
}; |
||||
|
||||
aliases { |
||||
led-boot = &power_green; |
||||
led-failsafe = &power_red; |
||||
led-running = &power_green; |
||||
led-upgrade = &power_green; |
||||
}; |
||||
|
||||
leds { |
||||
compatible = "gpio-leds"; |
||||
pinctrl-names = "default"; |
||||
pinctrl-0 = <&jtag_disable_pins>; |
||||
|
||||
wlan2g_red { |
||||
label = "wg800hp:red:wlan2g"; |
||||
gpios = <&gpio 6 GPIO_ACTIVE_LOW>; |
||||
}; |
||||
|
||||
active_red { |
||||
label = "wg800hp:red:active"; |
||||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>; |
||||
}; |
||||
|
||||
active_green { |
||||
label = "wg800hp:green:active"; |
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>; |
||||
}; |
||||
|
||||
power_red: power_red { |
||||
label = "wg800hp:red:power"; |
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>; |
||||
}; |
||||
|
||||
power_green: power_green { |
||||
label = "wg800hp:green:power"; |
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>; |
||||
default-state = "on"; |
||||
}; |
||||
|
||||
wlan5g_red { |
||||
label = "wg800hp:red:wlan5g"; |
||||
gpios = <&gpio 16 GPIO_ACTIVE_HIGH>; |
||||
}; |
||||
|
||||
wlan5g_green { |
||||
label = "wg800hp:green:wlan5g"; |
||||
gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; |
||||
linux,default-trigger = "phy0tpt"; |
||||
}; |
||||
|
||||
wlan2g_green { |
||||
label = "wg800hp:green:wlan2g"; |
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>; |
||||
linux,default-trigger = "phy1tpt"; |
||||
}; |
||||
}; |
||||
|
||||
keys { |
||||
compatible = "gpio-keys"; |
||||
|
||||
br { |
||||
label = "br"; |
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>; |
||||
linux,code = <BTN_0>; |
||||
linux,input-type = <EV_SW>; |
||||
debounce-interval = <60>; |
||||
}; |
||||
|
||||
reset { |
||||
label = "reset"; |
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>; |
||||
linux,code = <KEY_RESTART>; |
||||
debounce-interval = <60>; |
||||
}; |
||||
|
||||
wps { |
||||
label = "wps"; |
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>; |
||||
linux,code = <KEY_WPS_BUTTON>; |
||||
debounce-interval = <60>; |
||||
}; |
||||
}; |
||||
}; |
||||
|
||||
&spi { |
||||
status = "okay"; |
||||
num-cs = <1>; |
||||
|
||||
flash@0 { |
||||
compatible = "jedec,spi-nor"; |
||||
reg = <0>; |
||||
spi-max-frequency = <25000000>; |
||||
|
||||
partitions { |
||||
compatible = "fixed-partitions"; |
||||
#address-cells = <1>; |
||||
#size-cells = <1>; |
||||
|
||||
partition@0 { |
||||
label = "u-boot"; |
||||
reg = <0x000000 0x040000>; |
||||
read-only; |
||||
}; |
||||
|
||||
partition@40000 { |
||||
label = "u-boot-env"; |
||||
reg = <0x040000 0x010000>; |
||||
read-only; |
||||
}; |
||||
|
||||
partition@50000 { |
||||
compatible = "denx,uimage"; |
||||
label = "firmware"; |
||||
reg = <0x050000 0x6f0000>; |
||||
}; |
||||
|
||||
partition@740000 { |
||||
label = "user_data"; |
||||
reg = <0x740000 0x0a0000>; |
||||
read-only; |
||||
}; |
||||
|
||||
partition@7e0000 { |
||||
label = "board_data"; |
||||
reg = <0x7e0000 0x010000>; |
||||
read-only; |
||||
}; |
||||
|
||||
art: partition@7f0000 { |
||||
label = "art"; |
||||
reg = <0x7f0000 0x010000>; |
||||
read-only; |
||||
}; |
||||
}; |
||||
}; |
||||
}; |
||||
|
||||
&mdio0 { |
||||
status = "okay"; |
||||
|
||||
phy0: ethernet-phy@0 { |
||||
reg = <0>; |
||||
|
||||
qca,ar8327-initvals = < |
||||
0x04 0x00000080 /* PORT0 PAD MODE CTRL */ |
||||
0x50 0xcc35cc35 /* LED_CTRL0 */ |
||||
0x54 0xca35ca35 /* LED_CTRL1 */ |
||||
0x58 0xc935c935 /* LED_CTRL2 */ |
||||
0x5c 0x03ffff00 /* LED_CTRL3 */ |
||||
0x7c 0x0000007e /* PORT0_STATUS */ |
||||
>; |
||||
}; |
||||
}; |
||||
|
||||
ð0 { |
||||
status = "okay"; |
||||
|
||||
phy-mode = "sgmii"; |
||||
phy-handle = <&phy0>; |
||||
}; |
||||
|
||||
&pcie { |
||||
status = "okay"; |
||||
}; |
||||
|
||||
&uart { |
||||
status = "okay"; |
||||
}; |
||||
|
||||
&wmac { |
||||
status = "okay"; |
||||
qca,no-eeprom; |
||||
}; |
Loading…
Reference in new issue