Refreshed all patches.
Added new patch:
- 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch
This fixes a bug introduced in upstream 4.14.68 which caused targets using
ubifs to produce file-system errors on boot, rendering them useless.
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Some systems require multiple flash chips to be concatenated and read as
a single mtd device. The ar71xx target provides custom code to create
such mtdconcat devices. When porting devices to ath79, however, there is
no way to create such devices from within the device tree.
This commit adds a driver for creating virtual mtd-concat devices to the
ath79 target. Nodes must have a compatible = "virtual,mtd-concat" line,
and define a list of devices to concat in the 'devices' property,
for example:
flash {
compatible = "virtual,mtd-concat";
devices = <&flash0 &flash1>;
};
The driver is added to the very end of the mtd Makefile to increase the
likelyhood of all child devices already being loaded at the time of
probing, preventing unnecessary deferred probes which might in turn
cause other problems (like failure to load MAC addresses from art because
the partitions are not loaded yet).
Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
By default the RPS delegation will happen by masking the last few bits of
skb->hash. This patch adds an inermediate hash bucket that maps the masked
hash to a RPS core. This makes RPS results much more deterministic on SMP
systems.
Signed-off-by: John Crispin <john@phrozen.org>
The intention of 967b6be118 ("ar8327: Add workarounds for AR8337
switch") was to remove the register fixups for AR8337. But instead they
were removed for AR8327.
The RGMII RX delay is forced even if the port is used as phy instead of
mac, which results in no package flow at least for one board.
Fixes: FS#1664
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following patch was integrated upstream:
* target/linux/generic/backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
This fixes tries to work around the following security problems:
* CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects
* CVE-2018-3646 L1 Terminal Fault Virtualization related aspects
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the ability to configure specific functions of the
at803x series ethernet-PHYs, which were previously configured
exclusively with the help of platform-data, via device-tree.
This is needed to fully support existing boards of the ar71xx platform.
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport an upstream fix for a remotely exploitable TCP denial of service
flaw in Linux 4.9+.
The fixes are included in Linux 4.14.59 and later but did not yet end up in
version 4.9.118.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jonas Gorski commented on the previous patch:
|This is actually the wrong fix and papers over an issue in one of our
|local patches.
|
|We intentionally allow regmap to be built as a module, see
|
|/target/linux/generic/hack-4.14/259-regmap_dynamic.patch
|[...]
|[The regulator code] optionally supports regmap thanks to the stubs
|provided if regmap is disabled - which breaks if you compile regmap
|as a module.
In order to mitigate this issue, this patch reverts the previous patch
and replaces the existing IS_ENABLED(CONFIG_REGMAP) with
IS_REACHABLE(CONFIG_REGMAP). This solves this particular issue as the
regulator code will now automatically fallback to the regmap stubs in
case the kmod-regmap module is enabled, but nothing else sets
CONFIG_REGMAP=y.
Note: There's still a potential issue that this patch doesn't solve:
If someone ever wants to make a OpenWrt kernel package for a
regulator module that requires the REGMAP feature for a target that
doesn't set CONFIG_REGMAP=y but has CONFIG_REGULATOR=y, the resulting
kmod-regulator-xyz package will not work on the target.
Luckily, there aren't any in-tree OpenWrt kernel module packages for
regulators at the moment. On the bright side: regmap is a critical
part nowadays and all new and upcoming architectures require it by
default. This will likely only ever be a problem for legacy targets
and devices that cannot afford to enable REGMAP.
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: John Crispin <john@phrozen.org>
Fixes: d00913d121 ("kernel: modules: fix kmod-regmap")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Refreshed all patches
Remove upstreamed patches.
- 103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
- 001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch
- 001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- 001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- 900-gen_stats-fix-netlink-stats-padding.patch
Introduce a new backported patch to address ext4 breakage, introduced in 4.9.112
- backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
This patch has been slightly altered to compensate for a new helper function
introduced in later kernels.
Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9
Compile-tested on: ar71xx, bcm2710
Runtime-tested on: ar71xx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
AT803X_REG_CHIP_CONFIG and AT803X_BT_BX_REG_SEL have been defined
upstream by commit f62265b53ef3 ("at803x: double check SGMII side autoneg")
An existing local patch then added those exact same defines again which
isn't necessary, so remove them.
Fixes: f791fb4af4 ("kernel: add linux 4.9 support")
Fixes: b3f95490b9 ("kernel: generic: Add kernel 4.14 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch was wrongly removed by a kernel version bump to 4.9.105 in
the believe that it was merged upstream thow it wasn't. This lead to
unrecoverable link losses on devices which use those PHYs such as
many ubnt single-port CPEs.
Fixes: 7dca1bae82 (kernel: bump to 4.9.105)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The previous round of fixes for the 82574 chip cause an issue with
emulated e1000e devices in VMware ESXi 6.5. It also contains changes
that are not strictly necessary. These patches fix the issues introduced
in the previous series, revert the unnecessary changes to avoid
unforeseen fallout, and avoid a case where interrupts can be missed.
The final two patches of this series are already in the kernel, so no
need to include them here.
Patchwork: https://patchwork.ozlabs.org/cover/881776/
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This changes the DT binding's compatible property to
"ecoscentric,redboot-fis-partitions", removing the existing reference to
Red Hat.
Per the documentation hosted at eCosCentric's website, eCosCentric is
RedBoot's sole commercial maintainer since 2002, and the project has
been under the stewardship of the Free Software Foundation since 2008.
This also updates the property in the Inventel Livebox 1 .dts, the
binding's only current user.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
This fixes:
drivers/mtd/redboot.c:299:34: error: array type has incomplete element type 'struct of_device_id'
Fixes: 5e8b4be531 ("kernel: add DT binding support to the mtd redboot parser")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
In boards with fdt is impossible to use kmod-w1-gpio-custom.
w1-gpio-custom create platform structure for w1-gpio module,
but if board use fdt, data is ignored in w1-gpio probe.
This workaround fix the problem.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is a new & warm feature that allows nesting partiitons in DT and
mixing their types (e.g. static vs. dynamic). It's very useful for
boards that have most partitions static but some of them require extra
parsing (e.g. a "firmware" partition).
It's required to successfully backport support for new devices using
that new syntax in their DT files.
Since brcm63xx has a custom alternative patch the upstream one is being
reverted for it. The plan is to make brcm63xx use the upstream
implementation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
With a10a204aab ("kernel: make ubi auto-attach check for a tar file
magic") the check for the magic was added without considering a failing
mtd_read(). If the read fails, no check is done and the mount code is
called straight away.
Failing with an error message for such cases seems to me the cleaner way,
as it would allow to spot hidden/workaround issues.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The first block(s) of the ubi mtd device might be bad. We need to take
care on our own to skip the bad block(s) and read the next one(s).
Don't treat recoverable read errors as fatal and check for the UBI magic
if the data of a block could be recovered using ECC or similar.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move the put_mtd_device() called on multiple error conditions to a goto
label to use it later for more error conditions.
The early return on failed open of the mtd device and mismatching mtd
type allows to get rid of one level of indentation. By jumping to the
cleanup code, a refcount bug is fixed for the wrong flash type condition.
While at it, make clear that we only check for the UBI magic if the read
from flash was successful.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Extend the small_flash feature to disable swap, core dumps, and
kernel debug info, and change the squashfs block size to 1024KiB.
Also change squashfs fragment cache to 2 for small_flash to ease memory
usage.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Add a new config option to allow to select the default compile
optimization level for the kernel.
Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.
Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.
Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.
Exceptions to the above are:
- lantiq, where the optimization for size is only required for the
xway_legacy subtarget but was set for the whole target
- mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
plenty of space and an optimization for size doesn't make much sense
- rb532, which has 128MByte flash
Signed-off-by: Mathias Kresin <dev@kresin.me>
Newer kernels have a patch that implements compatible functionality
directly. Adjust the attribute of our own patch in preparation for
dropping it later
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Koen Vandeputte