Lima is a module for the (IoE) internet of everything applications,
based on Qualcomm/Atheros QCA4531.
Specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- USB 2.0 Host
- PCIe
- UART for serial console
- 14x GPIO
Flash instruction:
1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin
and rename it to 8dev_recovery.bin
2. Binary file copy to USB stick and plug into slot USB
3. Press S2 (reset) button
4. Press and hold the S1 button by 5 seconds
5. Wait ~40 seconds to complete recovery
Tested on:
- Lima development kit
Signed-off-by: Karol Dudek <karoiz@sli.pl>
commit 33b72b8e0f
"ar8216: adjust ATU flushing in case of link changes"
introduced portwise flushing on link down events. Now the ARL table could
be in a chaotic state after boot where ar8xxx_sw_get_arl_table looped
forever (depending on the entries collected while booting).
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict
[ 0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm
[ 0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22
[ 0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0 on device rt2880-pinmux
[ 0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back
Keep PWM disabled.
Signed-off-by: Furong Xu <xfr@outlook.com>
The Asus WL-500W buttons are active high,
but the software treats them as active low.
Fix the inverted logic.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
BCM4704 SoC has only USB 1.1 core:
ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
but this device actually comes with two USB 2.0 ports.
It appears embedded controller isn't used but instead there are two PCI
attached controllers (next to the BCM4321 wireless card):
1106:3038 VT82xx/62xx UHCI USB 1.1 Controller
1106:3104 USB 2.0
Choose a set of USB drivers which actually support this hardware.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
When memory is tight, modules may need to be loaded into vmalloc()
space. The code then has to generate jump trampolines which enable
relocations between vmalloc space and physical address space.
The code had a bug that was freeing these trampolines even when the
module was successfully loaded.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The cAP 2nD, mAP 2nD and wAP 2nD apparently all share the same QCA953x/SPI-NOR
platform.
This patch adds preliminary kernel support based on init data used in
Mikrotik's linux-3.3.5 kernel patch. Since this is totally experimental and
untested, the necessary glue in base-files has not been added, the code is
provided as a starting point in case somebody with that hardware wants to help
getting it supported.
The cAP lite (cAPL 2nD) should also be supported once it is determined whether
or not it uses the same board identifier as the mAP lite.
Code has been successfully built and has no side effect (no impact on already
supported devices).
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch adds support for the MikroTik RouterBOARD hEX lite
https://routerboard.com/RB750r2
Specifications:
- SoC: Qualcomm QCA9531 (850MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in)
This ethernet router is based on the same platform as the hEX PoE lite (it
shares the same board identifier), but has no USB and no PoE out.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch adds support for the MikroTik RouterBOARD hEX PoE lite
https://routerboard.com/RB750UPr2
Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A
This ethernet router is based on the same platform as the wireless router hAP.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch implements support for the hAP lite in mach-rbspi.c
hAP lite was supported via mach-rb941.c, so this file is removed
as well as the corresponding build bits.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch adds support for the MikroTik RouterBOARD mAP lite
https://routerboard.com/RBmAPL-2nD
Specifications:
- SoC: Qualcomm QCA9533 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9533, 2x2:2
- Ethernet: 1x100M
This is another 16M SPI NOR mikrotik device. The machine file is named
mach-rbspi.c because I plan to add support for several of the other spi-based
RouterBOARD devices in subsequent patches: they share most of the hardware
and thus the same codebase.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Some boards were apparently forgotten when ralink,portmap was renamed
to mediatek,portmap -- probably because they used the long obsolete
ralink,port-map attribute.
If this commit breaks ethernet wan/lan assignment, this is because
the port-map attribute wasn't actually parsed, you'll have to replace
"wllll" by "llllw" in the dts file belonging to that board (and send
a patch doing that!)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds the default LED and network settings for the PC Engines APU2
when running under the x86 target.
[dwmw2: Change Ethernet port setup]
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Based on a patch from Chris Blake <chrisrblake93@gmail.com>, except let's
do it by using the LED configuration instead of hard-coding it for each
board type. And try using /bin/board_detect to do the default behaviour,
on the first boot where the config hasn't yet been generated.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This change moves the files in 657418d to the root of the x86 target.
This is done in preperation for adding more devices under other
subtargets.
CC: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The DWR-512 embeds the hw slic device si3210. This device have the IRQ line
attached to the gpio1. This patch export the gpio1 with proper name and
parameters to the sysfs.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
this caused
'mv: can't rename '/mnt/sysupgrade.tgz': No such file or directory'
when running sysupgrade -n
Signed-off-by: John Crispin <john@phrozen.org>
Add support for the EBR-2310, which is almost identical to the DIR-615
rev E4, without the wifi.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.
Available FLASH space, with LEDE trunk, is only 240 KB.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.
Configure LAN as eth0 instead.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Karol Dudek