* add gdma and hsdma kernel modules
* i2s support all ramips targets except rt288x
* i2s need gdma to transfer data
* add simple audio kernel module. it support device tree binding
Signed-off-by: Michael Lee <igvtee@gmail.com>
D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash,
3.5mm audio out support. but no ethernet and usb ports.
so you must default enable wifi.
Signed-off-by: Michael Lee <igvtee@gmail.com>
The NixCore X1 is a Ralink/MediaTek rt5350 WiFi Module.
http://nixcores.com/
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Drew Gaylo <drew@nixcores.com>
The partition size is wrong, leading to out-of-disk-space even on no/moderate use.
Upstream fix from vendor: 2f25eb57ed
Suggested fix for openwrt: https://dev.openwrt.org/ticket/20321
Signed-off-by: Rene Treffer <treffer@measite.de>
Pinmux for rgmii needs to be set to rgmii, not gpio.
Hide the ESW switch on boot (using new rgmii esw devicetree attribute).
Also add a Sitecom-specific profile, since the image needs to include
the rtl8366 kernel driver.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
Commit "kernel: mtdsplit: calculate kernel partition precisely for Seama"
changed the kernel partition to only contain the kernel itself and not
the Seama header. Adjust the fixseama call to match what is used on
brcm53xx.
This fixes failing to boot a second time after flashing the factory image
on the affected devices.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has
64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with
802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac
MT7612E-based 5 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
names. and the hardware don't support error status. so i remove it.
but the logic is the same.
Signed-off-by: Michael Lee <igvtee@gmail.com>
Commit 9ff8928bb9 renamed the snd-soc-mt7620-i2s
driver and dropped snd-soc-mt7620-wm8960 which selected CONFIG_SND_SOC_WM8960
breaking all ramips builds due to undefined kernel config symbols.
Rework the kmod-sound-mt7620 package to explicitely select the
CONFIG_SND_SOC_WM8960 symbols and change it to bundle the renamed .ko file.
Also remove the @BROKEN flag and exclude it on the rt288x subtarget instead.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.
Signed-off-by: Michael Lee <igvtee@gmail.com>
* remove mt7620-wm8960.c use simple card and DTS to do it
* add old chips support
* add 12Mhz refclk setup. this is hard code. need use clock framework
rewrite it
* add interrupt error status support for debug. default disable it.
because it cause to many interrupts
* add setup bclk suport not hard code it
* add 24 bits support for mt7628. not verified
* use regmap api to control registers
* add txdma-req/rxdma-req DTS params for DMA use
Signed-off-by: Michael Lee <igvtee@gmail.com>
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
names. and the hardware don't support error status. so i remove it.
but the logic is the same.
Signed-off-by: Michael Lee <igvtee@gmail.com>
* fix compiler error. device_control operation not support now.
* add old chips support 8 channels. new chips support 16 channels.
* add mt7621 hsdma driver. data sheet says it has two channels.
but after test only one channel support.
* add memory to memory DMA support. i use dmatest kernel module to
verify this function. on rt305x it will copy more data. on mt7621
only two channels can works at the same time. these two chips
maybe have hardware bugs. because on other chips don't have these bugs.
* use tasklet to handle remaining dma requests.
Signed-off-by: Michael Lee <igvtee@gmail.com>
- Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620.
- Allow up to 3 uarts on MT7621 and MT7628.
- Remove unneeded SERIAL_8250_RT288X for MT7628.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.
Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The previous image creation code would have failed if the
unpadded kernel uImage size was less than 64 bytes from the
next erase block boundary. Fix that.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
The bootloader on this device expects the kernel partition to end
on a 64k boundary. The last 64 byte of the kernel partition must
contain a valid uImage header (the fakeroot partition).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
Jo-Philipp Wich