busybox tries to be smart and passes a number of additional flags to the
compiler. Unfortunately, the i386-specific flags break ABI compatiblity
with libc.
Fixes busybox crashes observed on x86-generic with GCC 7.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Newer GCC versions are reported to improve code size on various ARM
devices, which is why newer u-boot versions require them now.
There have also been user reports of data corruption issues fixed on
MIPS by updating from GCC 5 to GCC 7.
This update was previously held up by these two MIPS compile issues,
which have since been fixed:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83496https://gcc.gnu.org/bugzilla/show_bug.cgi?id=84790
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This updates musl from a commit between 1.1.18 and 1.1.19 to the final
release of the version 1.1.19.
This mostly fixes bugs in musl.
The size of the uncompressed binary is increased by about 4 KB.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Optimize the compiler output for larger cache blast cases that are
common for DMA-based networking.
On ar71xx, I measured a routing throughput increase of ~8%
Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts the changes needed for the upstream b53 DSA switch driver
to use the OpenWrt b43 swconfig switch driver instead.
Tested-by: TheWerthFam <thewerthfam@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit introduces new subtarget for Marvell EBU Armada Cortex A53
processor based devices.
The first device is Globalscale ESPRESSObin. Some hardware specs:
SoC: Marvell Armada 3700LP (88F3720) dual core ARM Cortex A53
processor up to 1.2GHz
RAM: 512MB, 1GB or 2GB DDR3
Storage: SATA interface
µSD card slot with footprint for an optional 4GB EMMC
4MB SPI NOR flash for bootloader
Ethernet: Topaz Networking Switch (88E6341) with 3x GbE ports
Connectors: USB 3.0
USB 2.0
µUSB port connected to PL2303SA (USB to serial bridge
controller) for UART access
Expansion: 2x 46-pin GPIO headers for accessories and shields with
I2C, GPIOs, PWM, UART, SPI, MMC, etc
MiniPCIe slot
Misc: Reset button, JTAG interface
Currently booting only from µSD card is supported.
The boards depending on date of dispatch can come with various U-Boot
versions. For the newest version 2017.03-armada-17.10 no manual
intervention should be needed to boot OpenWrt image. For the older ones
it's necessary to modify default U-Boot environment:
1. Interrupt boot process to run U-Boot command line,
2. Run following commands:
(for version 2017.03-armada-17.06 and 2017.03-armada-17.08)
setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
(for version 2015.01-armada-17.02 and 2015.01-armada-17.04)
setenv bootargs "console=ttyMV0,115200 root=/dev/mmcblk0p2 rw rootwait"
setenv bootcmd "ext4load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb; ext4load mmc 0:1 ${kernel_addr} Image; booti ${kernel_addr} - ${fdt_addr}"
saveenv
3. Poweroff, insert SD card with OpenWrt image, boot and enjoy.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Adds support for the Turris Omnia and builds an eMMC sysupgrade image in
the same format as the SolidRun ClearFog.
An initramfs image in the simple yet Omnia-specific 'medkit' image format
is also built in order to ease the initial flashing process.
Notable hardware support omissions are support for switching between SFP
cage and copper PHY, and RGB LED control.
Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used.
Specifications:
- Marvell Armada 385 1.6GHz dual-core ARMv7 CPU
- 1GB DDR3 RAM
- 8GB eMMC Flash
- 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports)
- 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN
- 2x USB 3.0
- 12x dimmable RGB LEDs controlled by independent MCU
- 3x Mini PCIe slots
- Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz)
- Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz)
- Optional Quectel EC20 Mini PCIe LTE modem
Flash instructions:
If the U-Boot environment has been modified previously (likely manually via
serial console), first use serial to reset the default environment.
=> env default -a
=> saveenv
Method 1 - USB 'medkit' image w/o serial
- Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and
omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a
USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS.
Note that the medkit MUST be named omnia-medkit*.tar.gz
- Disconnect other USB devices from the Omnia and connect the flash drive
to either USB port.
- Power on the Omnia and hold down the rear reset button until 4 LEDs are
illuminated, then release.
- Wait approximately 2 minutes for the Turris Omnia to flash itself with
the temporary image, during which LEDs will change multiple times.
- Connect a computer to a LAN port of the Turris Omnia with a DHCP client
- (if necessary) ssh-keygen -R 192.168.1.1
- ssh root@192.168.1.1
$ mount /dev/sda1 /mnt
$ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself and you can remove the flash drive.
Method 2 - TFTP w/ serial
- Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy
dtb + zImage to your TFTP server (rename if desired)
- Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server
- Connect serial console and interrupt U-Boot
=> dhcp
=> setenv serverip <tftp_server_ip_here>
=> tftpboot 0x01000000 zImage
=> tftpboot 0x02000000 dtb
=> bootz 0x01000000 - 0x02000000
- OpenWrt will now boot from ramdisk
- Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/
$ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
As at this commit, DSA is not enabled in the kernel config for mvebu, so these
nodes have been ignored. In preparation for the first mvebu board using DSA,
disable these nodes for existing boards to avoid issues.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9984.
The update fixes "ath10k_pci 0001:01:00.0: Invalid VHT mcs 15 peer
stats" spamming the kernel ring buffer at very high frequencies, but
introduces the new "ath10k_pci 0001:01:00.0: Unknown eventid: 36925".
This new warning doesn't appear to cause problems in practice and is
only emitted relatively rarely, not causing dmesg to overflow within
minutes.
Tested on the ZyXEL NBG6817; early feedback also suggests this firmware
to work well (with the same fixes and caveats) on the Netgear r7800 as
well.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This patch updates ath10k-firmware to last commit and use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9888.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Only register the chipidea usb device if the strapping option indicates
device mode. If not, use the regular ehci platform driver.
Add qca955x device mode support, tested on 8devices Rambutan.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
392811a ubus: let fw3_ubus_address() return the number of resolved addresses
359adcf options: emit an empty address item when resolving networks fails
503db4a zones: disable masq when resolving of all masq_src or masq_dest items failed
f50a524 helpers: implement explicit CT helper assignment support
a3ef503 zones: allow per-table log control
8ef12cb iptables: fix possible NULL pointer access on constructing rule masks
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The default fragment low/high thresholds are 3 and 4 MB. On devices with
only 32MB RAM, these settings may lead to OOM when many fragments that
cannot be reassembled are received. Decrease fragment low/high thresholds
to 384 and 512 kB on devices with less than 64 MB RAM.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Copying ./src/* would fail when src exists, but is empty or only contains
hidden files.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In addition to removing redundant code, this fixes various issues in
IB-generated images that have been fixed in prepare_rootfs before,
including better handling of CONFIG_CLEAN_IPKG and enabling of initscripts
from FILES.
We also reuse the opkg macro and remove --force-... flags that have been
removed from rootfs.mk as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
/usr/lib/opkg/status must not be removed completely, otherwise the
packages' conffile lists will be missing. Replace it with a reduced version
only containing the conffile entries.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
When a user removes a preinstalled opkg package, the package's prerm script
(and in particular our default_prerm) should run.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Many packages use the opkg conffiles field to list configuration files that
are to be retained on upgrades. Make this work on systems without opkg.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The Lantiq XRX200 aka VR9 doesn't have an asc0. Instead,
there is an USIF module which can either be an UART or a
SPI Controller.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
The package still leaks some user space linker options into the kernel
space. This breaks the build when ASLR is activated, deactivate it for
now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the datasheet the mt7620n have a fixed switch configuration
with 5 ephy (10/100) port. No RGMII configuration is possible.
Drop the mdio node as well. Without RGMII, the mdio node doesn't make any
sense
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
[drop mdio node, enable port4 by default]
Signed-off-by: Mathias Kresin <dev@kresin.me>
In some boards port 4 of mt7620 switch is powered down in bootloader
configuration as lan/wan package leak mitigation.
Reset ephy port 4 to default settings to power up the port.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[clarify issue in commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Felix Fietkau