Patch reverts 43332 which seems to cause issues with VLAN functionality.
Add a specific check to check whether ANEG is still enabled and re-enable
it if necessary. Disable generic phy soft reset for kernel >=3.16.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43356
This target can be emulated using ARM's Foundation_V8 simulator
software or qemu-system-aarch64 using the command-line described in the
README file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43355
Since we updated autoconf in r42855 we also need to enforce its use
while building eglibc to allow it to build successfully.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43352
Move compatible strings from board structs into separate table. This
allows for several board compatibles to match to the same board in case
e.g. only the flash size / partitions differ.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43341
We should make sure that also for ar8216 hw gets initialized.
For ar8216 hw_init is a dummy currently. The hw_init used for ar8236
should be generic enough to be usable with ar8216 too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43334
Move the PHY fixup call to the PHY init loop.
Use ar8xxx_has_gige in the PHY init instead of passing the gigE
capability via function parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43333
Kernel 3.14 introduced a switch reset in phy_init_hw in drivers/net/phy
causing BMCR_ANENABLE to get cleared.
Due to the fact that ar8xxx_phy_config_aneg does nothing for
PHY 0 autonegatiation support remains disabled.
This can cause ports to operate at 10MBit/half-duplex only.
Fix this by calling genphy_config_aneg for PHY 0 too as
genphy_config_aneg sets BMCR_ANENABLE if it's not yet set.
Fixes: ticket 17800
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43332
PHY init code in the switch-specific hw_init functions is mainly
identical. Factor it out into a generic ar8xxx_phy_init function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43331
Move phy fixup code from the chip-specific hw_init functions into a
fixup_phys callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43330
Currently there is a fixed 1000ms wait time after the switch was reset.
Most if not all switches need much less time to perform a reset.
Therefore replace the fixed wait time with polling for BMCR_RESET to
be cleared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43329
All supported switches have 5 PHYs. Currently partially 5 is hardcoded
and partially switch-specific constants exist.
Replace them with a global constant.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43328
On out-of-tree modules depending on other out-of-tree modules from a
different tree, module dependencies are not filled properly.
This change helps with adding those dependencies in the AutoLoad call
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43323
wg302v1_fixup() looks for the ATAG_CMDLINE atag, it doesn't find it and
so it takes the last atag in the list and overwrites non allocated
memory.
The side effects are corrupted vital data and a kernel that doesn't
boot. More details here https://dev.openwrt.org/ticket/18356
The fix appends the fixup to the command line and updates the atag only
when it finds it.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
SVN-Revision: 43320
Few notes:
- redboot partitions are unusable
- redboot declares only 16M of RAM, hence the mem arg in cmdline and separate kernel config
- boots fine but only ethernet works for now
- split wiliboard and raidsonic boards into different subtargets
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 43319
Building current trunk with 3.18 kernel fired some errors like 'missed
dependancy of module XXX from library kmod_YYY.ko'. These patch fixes 3
of such issues which are critical to have a successful build.
Signed-off-by: Alexey N Vinogradov <a.n.vinogradov@gmail.com>
SVN-Revision: 43318
r37490 removed the actual driver but left the kmod definition intact,
causing the build system hapily creating an empty package for it.
Remove it also to not make it seem as if it still exists.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43316
ldd might be called for shell scrips during sysupgrade, causing it to
complain that they are not a dynamic executables.
This is a harmless error, so supress it to avoid confusing about them
being serious ones.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43315
ld-musl-*.so* is a symlink "broken" for the hostsystem, so wildcard
will skip it, causing LD_MUSL_NAME to empty and the ldd symlink pointing
to ../../lib directly.
This causes sysupgrade failing to copy any linked libaries and
consequently failing to run anything after switching to ram disk.
Fix this by creating a symlink directly pointing to where ld-musl-*.so*
points to.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43314
Update nf_conntrack_rtsp to latest version based on http://mike.it-loops.com/rtsp/ (rtsp-module-3.7-v2.tar.gz).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43311
* fixes a bug in multipart sms
* adds a new call to read the sim phone number (partially functioanl)
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43310
musl libc doesn't support the GNU getopt extension to parse non-option
arguments when the optstring starts with '-'.
This extension is used by some utilities, notably iptables, that
currently return with errors even with perfectly valid invocations.
The patch adds the code needed by getopt.c and getopt_long.c to
implement that extension.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
SVN-Revision: 43309
This patch adds 3.14 kernel support for the mpc85xx platform.
Works fine here with a TL-WDR4900 which seems to be the only
supported device using this platform.
There might be differences depending on HW version, therefore
I'd ask others to test too.
Changes to 3.10
missing config options added to 3.14 config file
patch 001: rebased
patch 100: rebased
patch 110: rebased
patch 120: rebased
patch 130: rebased
patch 140: minor adjustment
patch 200: removed, change went upstream
patch 210: rebased
patch 220: removed, change went upstream
patch 750: new, fixes an issue with ethernet port autoneg being
disabled due to changes in kernel phy handling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43308
Jonas Gorski