Previously only the power LED was working.
With this patch all leds except 5GHz are working.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[rephrased commit title, drop status property]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 67d019ac94015707926235a3ac0aa6bb12cee8c2)
The D-Link DIR-645 currently uses an incorrect logic level for its
buttons.
Correct them in order to prevent unintentional activation of failsafe
mode.
Reported-by: Perry Melange <isprotejesvalkata@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 929e8f0f553637076f2612fb1c2225c5cee1f7ab)
The current code acknowledged interrupts *after* polling.
This is the wrong way around, and could cause an interrupt to
be missed.
This is not likely to be fatal as another packet, and so another
interrupt, should come along soon. But maybe it is causing
problems, so let's fix it anyway.
Signed-off-by: NeilBrown <neil@brown.name>
(Note that this matches the upstream driver.)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Based on OpenWRT Table of Hardware > Xiaomi > Xiaomi Mi WiFi Mini
Switch Ports Defaults:
0, 1: LAN
4: WAN
6: CPU
Port in Web GUI (word printed on bottom of case)
WAN(Internet) map to switch port 4
LAN1(.) map to switch port 1
LAN2(..) map to switch port 0
CPU map to switch port 6
current setting is 1 WAN/ 4 LAN port, fix it.
Signed-off-by: Chih-Wei Chen <changeway@gmail.com>
[rebased after base-files split, fixed commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 3e88ab79b03917bc4b03b34db12edf622bde1de1)
WizFi630S had some pins changed in the release version of the board.
The run led, wps button and a slide switch where affected.
This patch is correcting this.
i2c is removed as it is sharing a pin with the run (system) led.
uart2 is enabled as it is also enabled in the OEM firmware.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
(backported from commit d0b229f553a814b22c16976e40a197f892c0c0df)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WIZnet WizFi630s board name is written slightly different it its OEM
OpenWrt firmware. This causes an incompatibility warning during flashing
with sysupgrade. This patch is adding the vendor board name to the
supported devices list to avoid this warning. For initial flashing you
can use sysupgrade via command line or luci beside of TFTP.
Do not keep the OEM configuration during sysupgrade.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
(cherry picked from commit 816973f42aa47d910d3e35c2f8f8eb9d67416396)
&wmac entry in WIZnet WizFi630S dts file was existing two times.
This is removing one of them.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
(cherry picked from commit b735bbcb1876196f33f044ed07325f8959a8967f)
WIZnet WizFi630S is using only 3 of the phy ports. The unused phy ports
draw unnecessarily power. This is disabling the unused phy ports.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
(cherry picked from commit 36d4c2272ec65490232e70d45b945b9f467b78f0)
ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should
be in the default image for this device.
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(backported from commit 0a182fcba6d9cb2cf74cae9114ea4770ef928f75)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In FS#2738 we can see that patch first introduced in
e8ebcff ("ramips: add a explicit reset to dwc2")
breaks USB functionality since 18.06. Thus, this patch should be removed.
Removed:
- 0032-USB-dwc2-add-device_reset.patch
Fixes: FS#2738
Fixes: FS#2964
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
(cherry picked from commit ab841b4393a4077a5819da1da040ab9a89e3b69d)
Increase the SPI frequency for ELECOM WRC-1900GST and WRC-2533GST
to 40 MHz by updating the common DTSI file.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[WRC-1900GST]
Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit b5ae70d0530d1a733816f921ae0fe4dd58251fbb)
Looking at the current upstream driver implementation, it seems like the
TX/RX flow control is enabled only if the flow control pause option is
resolved from the device/link partner advertisements (or otherwise set).
On the other hand, our current in-tree driver force enables TX/RX
flow control by default, thus possibly leading to TX timeouts if the
other end sends pause frames (which are not properly handled?):
WARNING: CPU: 3 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x1ac/0x324
NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out
Disabling the flow control on PORT 5 MAC seems to fix this issues as the
pause frames are then filtered out. While at it, I'm removing the if
condition completely as suggested, since this code is run only on mt7621
SoC, so there is no need to check for the silicon revisions.
Ref: https://lists.openwrt.org/pipermail/openwrt-devel/2017-November/009882.html
Ref: https://forum.openwrt.org/t/mtk-soc-eth-watchdog-timeout-after-r11573/50000/12
Suggested-by: Felix Fietkau <nbd@nbd.name>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c8f8e59816eca49d776562d2d302bf990a87faf0)
The property "ralink,port-map" has been obsolete long before
this device was added, and the device is a one-port anyway.
Just remove it.
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit c00b2df6c8e421ea7aa96f53178dc85db99f2305)
Refreshed all patches and removed upstreamed:
oxnas/001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch
oxnas/002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch
Fixes: CVE-2020-12114 and CVE-2020-11669
Runtime-tested on: qemu-x86-64
Compile-tested on: ath79/generic, x86/64, imx6
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's known that ZBT sells 256M variants of these routers. As a result,
our images won't be able to boot on these routers.
This commit removes memory node for them. With previously backported
memory detection patch, kernel is able to detect memory size itself.
Fixes: FS#3053
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and
Belkin F7C027 does not have a USB port anyway. Just drop it.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 1dedad2a00d8519d4892b8529b5f2fffcb768220)
This reverts commit c38074de92.
Since ZyXEL Keenetic has actually 8 MiB flash as fixed in the
previous patch, we can re-enable it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ZyXEL Keenetic has 8MB flash, but OpenWrt uses only 4MB.
This commit fixes the problem.
WikiDevi page [1] says that ZyXEL Keenetic has FLA1: 8 MiB, there is
an article with specs [2] (in Russian).
[1] https://wikidevi.wi-cat.ru/ZyXEL_Keenetic
[2] https://3dnews.ru/608774/page-2.html
Fixes: FS#2487
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
(cherry picked from commit fea232ae8feb6af780fd4fa78ebe9231778bf75a)
Stock firmware has a vendor-defined tail at the end of uImage for image
validation. This patch enables OpenWrt installation from stock firmware
without having to access the UART console.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit be3e98ce26da5e737744427e1d59dd1c0508edef)
This commit reenables the image creation for the D-Link DIR-645.
Images built for the D-Link DIR-645 work just fine, there is no reason
to disable the image creation for it.
I tested the OpenWrt 18.06.5 and 19.07.0-rc1 images, as well as an
image I built from the current 19.07 branch (git HEAD 62d5ece) with
the default 19.07 release config, and I cannot confirm the report that
commit 2607c02ed5
("ramips: disable D-Link DIR-645 by default") references.
Configuration changes were applied successfully and remained set after
a reboot as well. The log also showed no anomalies.
This reverts commit 2607c02ed5.
Signed-off-by: Mason Clarke <mclarke2355@gmail.com>
This converts the TP-Link TL-MR3020v3 board to use the WLAN throughput
LED trigger in order to react to all VAPs.
It also moves the WLAN trigger config of the TP-Link TL-WA801NDv5 to the
DTS and merges the now identical LAN LED configs.
Verified these changes on a TL-MR3020v3 and TL-WA801NDv5.
Signed-off-by: Jan Alexander <jan@nalx.net>
[changed commit title and extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[added comment about test result on TL-WA801ND v5]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 20eb45da4fc19c12ea2073471992eeaf9d602fa5)
DEVICE_PACKAGES is specified twice for the same device. Remove the
first (=older) assignment.
Fixes: 40692f0fb5 ("ramips: mt7620: select only the matching mt76 driver")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 4ecd6510bf8877dcd07561045852726ffbab8814)
Currently it's not possible to downgrade from master:
Device ubiquiti,edgerouterx not supported by this image
Supported devices: ubnt-erx
So fix it by adding a DTS based device name from master into
SUPPORTED_DEVICES list.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
"#mediatek,portmap" is not a valid property name.
If mediatek,portmap equals 0x0, then the esw driver ditches it and uses
the default value, 0x3f.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit f87281b2956110f10af9eb23fc6d327dfde7ab42)
mt76x8 uses esw_rt3050 driver, which does not accept mediatek,portmap with
string values. Convert the strings to integers to make it work.
According to its switch setup, WRTnode 2P/2R have a WAN port at port 0,
so the correct value should be 0x3e.
tplink_8m.dtsi uses "llllw", but it does not match switch setups of any
device using the DTSI. Remove it from the DTSI and add correct value to DTS
for each device.
These devices have a WAN port at port 0. Set the value to 0x3e.
- tplink,archer-c20-v4
- tplink,archer-c50-v3
- tplink,tl-mr3420-v5
- tplink,tl-wr840n-v4
- tplink,tl-wr841n-v13
- tplink,tl-wr842n-v5
These devices have only one ethernet port. They don't need portmap setting.
- tplink,tl-wa801nd-v5
- tplink,tl-wr802n-v4
- tplink,tl-wr902ac-v3
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(backported from commit 7a387bf9a0d73f7c581e2c9aeae6476588100e2c)
[removed TL-WR841N v14 which is not present in 19.07]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to 02_network portmap is wan=0 lan1=1 lan2=2 lan3=3 lan4=4
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
(cherry picked from commit ebf535a6cfefef5b0afb74cb01c9a17ab242b85b)
mt7620 and mt7621 use mt7530 driver, which only accepts "llllw", "wllll",
and "lwlll" values.
According to its switch setup, Mi Router 3G v2 has a WAN port at port 4,
so the correct value should be "llllw".
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(backported from commit d3c0a944059bb0d45c3b56278249100258378b0c)
[removed devices not in 19.07]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds factory image generation for all three
devices. These images can be flashed via WebUI
for easy installation.
Thanks to David Bauer for the inspiration.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[altered commit to only include the R6350]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3c8df280a96bbd81357d6eb52845e6b5fa7162fe)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Match LED behavior to stock firmware:
Red: booting
White: running
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
(cherry picked from commit 9a3c9a96563c3c3fb1e15b791d9117b193fed7a6)
HC5962 has only 3 LAN ports, switch port 0 is unused
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
(backported from commit 68f49df31507454f86b72a5c1e250505176baed7)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Now that the mt76/mt7615e driver is in Openwrt, might as well use it.
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
(cherry picked from commit d7c082ba4f7de97b3708d1f4a064954ffc774778)
- fix color and active mode for existing wps led
- add green wps led
- add wps button
Signed-off-by: Jan Alexander <jan@nalx.net>
[wrap line]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 26105974e7f9758cd4bc443ce0322983f818acd5)
This device OOPs during the boot due to broken flash. It can be probably
fixed with `broken-flash-reset` once ramips is on 4.19 kernel.
So disable images for this device until its fixed.
Ref: FS#2695, PR#2483
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 28080d54d217fb4ab112e079f69462fee695dbf8)
- add "gpio" group for wan_orange led
- use tpt triggers for wifi led indication
- add wifi 5 GHz led support
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[slight commit message adjustment, backport]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 3a538db60abfc50b47ce1774f66d489700a50c00)
This mostly reverts the original commit e9929ebeea ("ramips: Fix
sysupgrade for Xiaomi mir3g") and replaces it with setting the
BOARD_NAME to the old value.
This way the folder in the tar will be named sysupgrade-mir3g and not
sysupgrade-xiaomi_mir3g and the sysupgrade in OpenWrt 18.06 can find it.
Without this change sysupgrade from 18.06 to 19.07 is only possible with
the -F option.
I tested the following sysupgrades successfully without -F
18.06 -> 19.07
19.07 -> master
master -> 19.07
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without this change sysupgrade from 18.06 to 19.07 is only possible with
the -F option.
In OpenWrt 18.06 the nand_do_platform_check() function is called with
the board name mir3g only, if the tar does not use mir3g it will fail.
OpenWrt 19.07 and later support the metadata with the supported_devices
attribute to allow renaming. Do the renaming of the target between 19.07
and master like it is done for some other boards.
I tested the following sysupgrades successfully without -F
18.06 -> 19.07
19.07 -> master
master -> 19.07
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There are two identical wmac nodes in the dts file of MediaTek
LinkIt Smart 7688, so delete one of them.
Signed-off-by: Jack Chen <redchenjs@live.com>
(cherry picked from commit 4be271a4867dcf57a122eeb7b42407e7a506915e)
The TP-Link Archer C20i previously had a generic Ralink MAC address set
for both radios, as the caldata does only contain a generic MAC address.
Set the MAC address from the vendor firmware for both radios to assign
unique MAC addresses to every device.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3b013dcdf8d8aa0e3601e3aac30342318025e32a)
The TP-Link Archer C2 v1 previously had a generic Ralink MAC address set
for the 5GHz radio (MT7610), as the caldata does only contain a generic
MAC address.
Set the MAC address from the vendor firmware for the 5GHz radio to
assign unique MAC addresses to every device.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit dcc923a4c45b48fcbef4f3964f74fbcaabad335e)
Use the WPS LED to indicate system status like it is done for the
TP-Link Archer C2 v1 and many other boards.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit a272fafc9c507820cc62aa12464588bac45f250a)
This converts all MediaTek MT7620 boards from TP-Link to use the now
supported WiFi throughput LED trigger. This way, the LED state now
covers all VAPs regardless of their name.
Also align all single-WiFi LEDs to represent the state of the 2.4GHz
radio. This was not always the case previously, as later-added support
for the MT7610 altered the phy probing order.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1e7c6381f0058e49caab8de54eaad4862732f95d)
Davide Fioravanti