Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>master
parent
9a08c0ba80
commit
cec7e661e7
@ -1,82 +0,0 @@ |
||||
#ifndef __INC_DT2_COMMON_H |
||||
#define __INC_DT2_COMMON_H |
||||
|
||||
#define ATAG_MV_UBOOT 0x41000403 |
||||
|
||||
struct tag_mv_uboot { |
||||
u32 uboot_version; |
||||
u32 tclk; |
||||
u32 sysclk; |
||||
u32 isUsbHost; |
||||
u32 overEthAddr; |
||||
u8 dt2_eeprom[256]; |
||||
}; |
||||
|
||||
#define DT2_EEPROM_ADDR 0x50 |
||||
#define DT2_EEPROM_OFFSET 0 |
||||
#define DT2_EEPROM_LENGTH 256 |
||||
|
||||
#define DT2_SERIAL_NUMBER_DEFAULT "run on default\0" |
||||
#define DT2_REVISION_DEFAULT_INIT 0xFF |
||||
#define DT2_CONFIG_FLAGS_DEFAULT 0x00 |
||||
|
||||
#define _PACKED_ __attribute__((packed)) |
||||
|
||||
struct DT2_EEPROM_SD_CONFIG { |
||||
unsigned int ram_1; |
||||
unsigned int ram_2; |
||||
unsigned int ram_3; |
||||
unsigned int ram_4; |
||||
unsigned char ram_5; |
||||
unsigned char ram_6; |
||||
unsigned short ram_7; |
||||
unsigned int magic_id; |
||||
} _PACKED_; // 24 Bytes in total
|
||||
|
||||
struct DT2_EEPROM_FC_CONFIG { |
||||
unsigned char rtc_sts_mask; |
||||
unsigned char rtc_sts_init; |
||||
unsigned char rtc_int_mask; |
||||
unsigned char rtc_int_init; |
||||
unsigned char rtc_atrim_init; |
||||
unsigned char rtc_dtrim_init; |
||||
unsigned char dummy1; |
||||
unsigned char dummy2; |
||||
unsigned char dt2_config_flags; /* 0x80 to load rtc_values to RTC */ |
||||
unsigned char dt2_revision; /* upper nibble is HW, lower nibble is FW */ |
||||
unsigned char dt2_serial_number[16]; /* Serial number of DT-2 */ |
||||
} _PACKED_; // 26 Bytes in total
|
||||
|
||||
#define CFG_LOAD_RTC_VALUES 0x80 |
||||
|
||||
struct DT2_EEPROM_GW_CONFIG { |
||||
unsigned int dummy1; |
||||
unsigned int dummy2; |
||||
unsigned int dummy3; |
||||
unsigned char dummy4; |
||||
unsigned char tos_video_val1; |
||||
unsigned char tos_video_val2; |
||||
unsigned char tos_voip_val; |
||||
unsigned char qos_igmp_cfg; |
||||
unsigned char num_of_ifs; |
||||
unsigned short vlan_ports_if[3]; |
||||
unsigned char mac_addr[3][6]; |
||||
} _PACKED_; // 42 Bytes in total
|
||||
|
||||
#define _SIZE_OF_ALL_STRUCTS_ (sizeof(struct DT2_EEPROM_SD_CONFIG) + sizeof(struct DT2_EEPROM_FC_CONFIG) + sizeof(struct DT2_EEPROM_GW_CONFIG)) |
||||
|
||||
// MV = EEPROM - SD - FC - GW - CRC
|
||||
struct DT2_EEPROM_MV_CONFIG { |
||||
unsigned int reg_addr[(DT2_EEPROM_LENGTH - _SIZE_OF_ALL_STRUCTS_ - sizeof(unsigned int)) / (sizeof(unsigned int) * 2)]; |
||||
unsigned int reg_data[(DT2_EEPROM_LENGTH - _SIZE_OF_ALL_STRUCTS_ - sizeof(unsigned int)) / (sizeof(unsigned int) * 2)]; |
||||
} _PACKED_; |
||||
|
||||
struct DT2_EEPROM_STRUCT { |
||||
struct DT2_EEPROM_MV_CONFIG mv; |
||||
struct DT2_EEPROM_SD_CONFIG sd; |
||||
struct DT2_EEPROM_FC_CONFIG fc; |
||||
struct DT2_EEPROM_GW_CONFIG gw; |
||||
unsigned int crc; |
||||
} _PACKED_; |
||||
|
||||
#endif |
@ -1,445 +0,0 @@ |
||||
/*
|
||||
* arch/arm/mach-orion5x/dt2-setup.c |
||||
* |
||||
* Freecom DataTank Gateway Setup |
||||
* |
||||
* Copyright (C) 2009 Zintis Petersons <Zintis.Petersons@abcsolutions.lv> |
||||
* |
||||
* This file is licensed under the terms of the GNU General Public |
||||
* License version 2. This program is licensed "as is" without any |
||||
* warranty of any kind, whether express or implied. |
||||
*/ |
||||
|
||||
#include <linux/kernel.h> |
||||
#include <linux/init.h> |
||||
#include <linux/platform_device.h> |
||||
#include <linux/pci.h> |
||||
#include <linux/irq.h> |
||||
#include <linux/mtd/physmap.h> |
||||
#include <linux/mv643xx_eth.h> |
||||
#include <linux/ethtool.h> |
||||
#include <linux/if_ether.h> |
||||
#include <net/dsa.h> |
||||
#include <linux/ata_platform.h> |
||||
#include <linux/i2c.h> |
||||
#include <linux/reboot.h> |
||||
#include <linux/interrupt.h> |
||||
#include <asm/mach-types.h> |
||||
#include <asm/gpio.h> |
||||
#include <asm/mach/arch.h> |
||||
#include <asm/mach/pci.h> |
||||
#include <mach/orion5x.h> |
||||
#include "common.h" |
||||
#include "mpp.h" |
||||
|
||||
/*****************************************************************************
|
||||
* DT2 local |
||||
****************************************************************************/ |
||||
#include <asm/setup.h> |
||||
#include "dt2-common.h" |
||||
|
||||
u32 mvUbootVer = 0; |
||||
u32 mvTclk = 166666667; |
||||
u32 mvSysclk = 200000000; |
||||
u32 mvIsUsbHost = 1; |
||||
u32 overEthAddr = 0; |
||||
u32 gBoardId = -1; |
||||
struct DT2_EEPROM_STRUCT dt2_eeprom; |
||||
|
||||
/*****************************************************************************
|
||||
* DT2 Info |
||||
****************************************************************************/ |
||||
/*
|
||||
* PCI |
||||
*/ |
||||
|
||||
#define DT2_PCI_SLOT0_OFFS 7 |
||||
#define DT2_PCI_SLOT0_IRQ_A_PIN 3 |
||||
#define DT2_PCI_SLOT0_IRQ_B_PIN 2 |
||||
|
||||
#define DT2_PIN_GPIO_SYNC 25 |
||||
#define DT2_PIN_GPIO_POWER 24 |
||||
#define DT2_PIN_GPIO_UNPLUG1 23 |
||||
#define DT2_PIN_GPIO_UNPLUG2 22 |
||||
#define DT2_PIN_GPIO_RESET 4 |
||||
|
||||
#define DT2_NOR_BOOT_BASE 0xf4000000 |
||||
#define DT2_NOR_BOOT_SIZE SZ_512K |
||||
|
||||
#define DT2_LEDS_BASE 0xfa000000 |
||||
#define DT2_LEDS_SIZE SZ_1K |
||||
|
||||
/*****************************************************************************
|
||||
* 512K NOR Flash on Device bus Boot CS |
||||
****************************************************************************/ |
||||
|
||||
static struct mtd_partition dt2_partitions[] = { |
||||
{ |
||||
.name = "u-boot", |
||||
.size = 0x00080000, |
||||
.offset = 0, |
||||
}, |
||||
}; |
||||
|
||||
static struct physmap_flash_data dt2_nor_flash_data = { |
||||
.width = 1, /* 8 bit bus width */ |
||||
.parts = dt2_partitions, |
||||
.nr_parts = ARRAY_SIZE(dt2_partitions) |
||||
}; |
||||
|
||||
static struct resource dt2_nor_flash_resource = { |
||||
.flags = IORESOURCE_MEM, |
||||
.start = DT2_NOR_BOOT_BASE, |
||||
.end = DT2_NOR_BOOT_BASE + DT2_NOR_BOOT_SIZE - 1, |
||||
}; |
||||
|
||||
static struct platform_device dt2_nor_flash = { |
||||
.name = "physmap-flash", |
||||
.id = 0, |
||||
.dev = { |
||||
.platform_data = &dt2_nor_flash_data, |
||||
}, |
||||
.resource = &dt2_nor_flash_resource, |
||||
.num_resources = 1, |
||||
}; |
||||
|
||||
/*****************************************************************************
|
||||
* PCI |
||||
****************************************************************************/ |
||||
|
||||
void __init dt2_pci_preinit(void) |
||||
{ |
||||
int pin, irq; |
||||
|
||||
/*
|
||||
* Configure PCI GPIO IRQ pins |
||||
*/ |
||||
pin = DT2_PCI_SLOT0_IRQ_A_PIN; |
||||
if (gpio_request(pin, "PCI IntA") == 0) { |
||||
if (gpio_direction_input(pin) == 0) { |
||||
irq = gpio_to_irq(pin); |
||||
irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW); |
||||
printk (KERN_INFO "PCI IntA IRQ: %d\n", irq); |
||||
} else { |
||||
printk(KERN_ERR "dt2_pci_preinit failed to " |
||||
"irq_set_irq_type pin %d\n", pin); |
||||
gpio_free(pin); |
||||
} |
||||
} else { |
||||
printk(KERN_ERR "dt2_pci_preinit failed to request gpio %d\n", pin); |
||||
} |
||||
|
||||
pin = DT2_PCI_SLOT0_IRQ_B_PIN; |
||||
if (gpio_request(pin, "PCI IntB") == 0) { |
||||
if (gpio_direction_input(pin) == 0) { |
||||
irq = gpio_to_irq(pin); |
||||
irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW); |
||||
printk (KERN_INFO "PCI IntB IRQ: %d\n", irq); |
||||
} else { |
||||
printk(KERN_ERR "dt2_pci_preinit failed to " |
||||
"irq_set_irq_type pin %d\n", pin); |
||||
gpio_free(pin); |
||||
} |
||||
} else { |
||||
printk(KERN_ERR "dt2_pci_preinit failed to gpio_request %d\n", pin); |
||||
} |
||||
} |
||||
|
||||
static int __init dt2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) |
||||
{ |
||||
int irq; |
||||
|
||||
/*
|
||||
* Check for devices with hard-wired IRQs. |
||||
*/ |
||||
irq = orion5x_pci_map_irq(dev, slot, pin); |
||||
if (irq != -1){ |
||||
printk(KERN_INFO "orion5x_pci_map_irq: %d\n", irq); |
||||
return irq; |
||||
} |
||||
|
||||
/*
|
||||
* PCI IRQs are connected via GPIOs |
||||
*/ |
||||
switch (slot - DT2_PCI_SLOT0_OFFS) { |
||||
case 0: |
||||
if (pin == 1){ |
||||
irq = gpio_to_irq(DT2_PCI_SLOT0_IRQ_A_PIN); |
||||
printk(KERN_INFO "dt2_pci_map_irq DT2_PCI_SLOT0_IRQ_A_PIN: %d\n", irq); |
||||
} |
||||
else { |
||||
irq = gpio_to_irq(DT2_PCI_SLOT0_IRQ_B_PIN); |
||||
printk(KERN_INFO "dt2_pci_map_irq DT2_PCI_SLOT0_IRQ_B_PIN: %d\n", irq); |
||||
} |
||||
default: |
||||
irq = -1; |
||||
printk(KERN_INFO "dt2_pci_map_irq IRQ: %d\n", irq); |
||||
} |
||||
|
||||
return irq; |
||||
} |
||||
|
||||
static struct hw_pci dt2_pci __initdata = { |
||||
.nr_controllers = 2, |
||||
.preinit = dt2_pci_preinit, |
||||
.setup = orion5x_pci_sys_setup, |
||||
.scan = orion5x_pci_sys_scan_bus, |
||||
.map_irq = dt2_pci_map_irq, |
||||
}; |
||||
|
||||
static int __init dt2_pci_init(void) |
||||
{ |
||||
if (machine_is_dt2()) |
||||
pci_common_init(&dt2_pci); |
||||
|
||||
return 0; |
||||
} |
||||
|
||||
subsys_initcall(dt2_pci_init); |
||||
|
||||
/*****************************************************************************
|
||||
* Ethernet |
||||
****************************************************************************/ |
||||
|
||||
static struct mv643xx_eth_platform_data dt2_eth_data = { |
||||
.phy_addr = MV643XX_ETH_PHY_NONE, |
||||
.speed = SPEED_1000, |
||||
.duplex = DUPLEX_FULL, |
||||
}; |
||||
|
||||
static struct dsa_chip_data dt2_switch_chip_data = { |
||||
.port_names[0] = "wan", |
||||
.port_names[1] = "lan1", |
||||
.port_names[2] = "lan2", |
||||
.port_names[3] = "cpu", |
||||
.port_names[4] = "lan3", |
||||
.port_names[5] = "lan4", |
||||
}; |
||||
|
||||
static struct dsa_platform_data dt2_switch_plat_data = { |
||||
.nr_chips = 1, |
||||
.chip = &dt2_switch_chip_data, |
||||
}; |
||||
|
||||
/*****************************************************************************
|
||||
* RTC ISL1208 on I2C bus |
||||
****************************************************************************/ |
||||
static struct i2c_board_info __initdata dt2_i2c_rtc = { |
||||
I2C_BOARD_INFO("isl1208", 0x6F), |
||||
}; |
||||
|
||||
/*****************************************************************************
|
||||
* Sata |
||||
****************************************************************************/ |
||||
static struct mv_sata_platform_data dt2_sata_data = { |
||||
.n_ports = 2, |
||||
}; |
||||
|
||||
/*****************************************************************************
|
||||
* General Setup |
||||
****************************************************************************/ |
||||
static unsigned int dt2_mpp_modes[] __initdata = { |
||||
MPP0_GPIO, // RTC interrupt
|
||||
MPP1_GPIO, // 88e6131 interrupt
|
||||
MPP2_GPIO, // PCI_intB
|
||||
MPP3_GPIO, // PCI_intA
|
||||
MPP4_GPIO, // reset button switch
|
||||
MPP5_GPIO, |
||||
MPP6_GPIO, |
||||
MPP7_GPIO, |
||||
MPP8_GPIO, |
||||
MPP9_GIGE, /* GE_RXERR */ |
||||
MPP10_GPIO, // usb
|
||||
MPP11_GPIO, // usb
|
||||
MPP12_GIGE, // GE_TXD[4]
|
||||
MPP13_GIGE, // GE_TXD[5]
|
||||
MPP14_GIGE, // GE_TXD[6]
|
||||
MPP15_GIGE, // GE_TXD[7]
|
||||
MPP16_GIGE, // GE_RXD[4]
|
||||
MPP17_GIGE, // GE_RXD[5]
|
||||
MPP18_GIGE, // GE_RXD[6]
|
||||
MPP19_GIGE, // GE_RXD[7]
|
||||
0, |
||||
}; |
||||
|
||||
/*****************************************************************************
|
||||
* LEDS |
||||
****************************************************************************/ |
||||
static struct platform_device dt2_leds = { |
||||
.name = "dt2-led", |
||||
.id = -1, |
||||
}; |
||||
|
||||
/****************************************************************************
|
||||
* GPIO key |
||||
****************************************************************************/ |
||||
static irqreturn_t dt2_reset_handler(int irq, void *dev_id) |
||||
{ |
||||
/* This is the paper-clip reset which does an emergency reboot. */ |
||||
printk(KERN_INFO "Restarting system.\n"); |
||||
machine_restart(NULL); |
||||
|
||||
/* This should never be reached. */ |
||||
return IRQ_HANDLED; |
||||
} |
||||
|
||||
static irqreturn_t dt2_power_handler(int irq, void *dev_id) |
||||
{ |
||||
printk(KERN_INFO "Shutting down system.\n"); |
||||
machine_power_off(); |
||||
return IRQ_HANDLED; |
||||
} |
||||
|
||||
static void __init dt2_init(void) |
||||
{ |
||||
/*
|
||||
* Setup basic Orion functions. Need to be called early. |
||||
*/ |
||||
orion5x_init(); |
||||
|
||||
orion5x_mpp_conf(dt2_mpp_modes); |
||||
|
||||
/*
|
||||
* Configure peripherals. |
||||
*/ |
||||
|
||||
orion5x_uart0_init(); |
||||
orion5x_ehci0_init(); |
||||
orion5x_ehci1_init(); |
||||
orion5x_i2c_init(); |
||||
orion5x_sata_init(&dt2_sata_data); |
||||
orion5x_xor_init(); |
||||
|
||||
printk(KERN_INFO "U-Boot parameters:\n"); |
||||
printk(KERN_INFO "Sys Clk = %d, Tclk = %d, BoardID = 0x%02x\n", mvSysclk, mvTclk, gBoardId); |
||||
|
||||
printk(KERN_INFO "Serial: %s\n", dt2_eeprom.fc.dt2_serial_number); |
||||
printk(KERN_INFO "Revision: %016x\n", dt2_eeprom.fc.dt2_revision); |
||||
printk(KERN_INFO "DT2: Using MAC address %pM for port 0\n", |
||||
dt2_eeprom.gw.mac_addr[0]); |
||||
printk(KERN_INFO "DT2: Using MAC address %pM for port 1\n", |
||||
dt2_eeprom.gw.mac_addr[1]); |
||||
|
||||
orion5x_eth_init(&dt2_eth_data); |
||||
memcpy(dt2_eth_data.mac_addr, dt2_eeprom.gw.mac_addr[0], 6); |
||||
orion5x_eth_switch_init(&dt2_switch_plat_data, NO_IRQ); |
||||
|
||||
i2c_register_board_info(0, &dt2_i2c_rtc, 1); |
||||
|
||||
mvebu_mbus_add_window("devbus-boot", DT2_NOR_BOOT_BASE, |
||||
DT2_NOR_BOOT_SIZE); |
||||
|
||||
platform_device_register(&dt2_nor_flash); |
||||
|
||||
mvebu_mbus_add_window("devbus-cs0", DT2_LEDS_BASE, DT2_LEDS_SIZE); |
||||
platform_device_register(&dt2_leds); |
||||
|
||||
if (request_irq(gpio_to_irq(DT2_PIN_GPIO_RESET), &dt2_reset_handler, |
||||
IRQF_TRIGGER_LOW, |
||||
"DT2: Reset button", NULL) < 0) { |
||||
|
||||
printk("DT2: Reset Button IRQ %d not available\n", |
||||
gpio_to_irq(DT2_PIN_GPIO_RESET)); |
||||
} |
||||
|
||||
if (request_irq(gpio_to_irq(DT2_PIN_GPIO_POWER), &dt2_power_handler, |
||||
IRQF_TRIGGER_LOW, |
||||
"DT2: Power button", NULL) < 0) { |
||||
|
||||
printk(KERN_DEBUG "DT2: Power Button IRQ %d not available\n", |
||||
gpio_to_irq(DT2_PIN_GPIO_POWER)); |
||||
} |
||||
} |
||||
|
||||
static int __init parse_tag_dt2_uboot(const struct tag *t) |
||||
{ |
||||
struct tag_mv_uboot *mv_uboot; |
||||
|
||||
// Get pointer to our block
|
||||
mv_uboot = (struct tag_mv_uboot*)&t->u; |
||||
mvTclk = mv_uboot->tclk; |
||||
mvSysclk = mv_uboot->sysclk; |
||||
mvUbootVer = mv_uboot->uboot_version; |
||||
mvIsUsbHost = mv_uboot->isUsbHost; |
||||
|
||||
// Some clock fixups
|
||||
if(mvTclk == 166000000) mvTclk = 166666667; |
||||
else if(mvTclk == 133000000) mvTclk = 133333333; |
||||
else if(mvSysclk == 166000000) mvSysclk = 166666667; |
||||
|
||||
gBoardId = (mvUbootVer & 0xff); |
||||
|
||||
//DT2 specific data
|
||||
memcpy(&dt2_eeprom, mv_uboot->dt2_eeprom, sizeof(struct DT2_EEPROM_STRUCT)); |
||||
|
||||
return 0; |
||||
} |
||||
__tagtable(ATAG_MV_UBOOT, parse_tag_dt2_uboot); |
||||
|
||||
/*
|
||||
* This is OpenWrt specific fixup. It includes code from original "tag_fixup_mem32" to |
||||
* fixup bogus memory tags and also fixes kernel cmdline by adding " init=/etc/preinit" |
||||
* at the end. It is important to flash OpenWrt image from original Freecom firmware. |
||||
* |
||||
* Vanilla kernel should use "tag_fixup_mem32" function. |
||||
*/ |
||||
void __init openwrt_fixup(struct tag *t, char **from, struct meminfo *meminfo) |
||||
{ |
||||
char *p = NULL; |
||||
static char openwrt_init_tag[] __initdata = " init=/etc/preinit"; |
||||
|
||||
for (; t->hdr.size; t = tag_next(t)){ |
||||
/* Locate the Freecom cmdline */ |
||||
if (t->hdr.tag == ATAG_CMDLINE) { |
||||
p = t->u.cmdline.cmdline; |
||||
printk("%s(%d): Found cmdline '%s' at 0x%0lx\n", |
||||
__FUNCTION__, __LINE__, p, (unsigned long)p); |
||||
} |
||||
/*
|
||||
* Many orion-based systems have buggy bootloader implementations. |
||||
* This is a common fixup for bogus memory tags. |
||||
*/ |
||||
if (t->hdr.tag == ATAG_MEM && |
||||
(!t->u.mem.size || t->u.mem.size & ~PAGE_MASK || |
||||
t->u.mem.start & ~PAGE_MASK)) { |
||||
printk(KERN_WARNING |
||||
"Clearing invalid memory bank %dKB@0x%08x\n", |
||||
t->u.mem.size / 1024, t->u.mem.start); |
||||
t->hdr.tag = 0; |
||||
} |
||||
} |
||||
|
||||
printk("%s(%d): End of table at 0x%0lx\n", __FUNCTION__, __LINE__, (unsigned long)t); |
||||
|
||||
/* Overwrite the end of the table with a new cmdline tag. */
|
||||
t->hdr.tag = ATAG_CMDLINE; |
||||
t->hdr.size = |
||||
(sizeof (struct tag_header) + |
||||
strlen(p) + strlen(openwrt_init_tag) + 1 + 4) >> 2; |
||||
|
||||
strlcpy(t->u.cmdline.cmdline, p, COMMAND_LINE_SIZE); |
||||
strlcpy(t->u.cmdline.cmdline + strlen(p), openwrt_init_tag, |
||||
COMMAND_LINE_SIZE - strlen(p)); |
||||
|
||||
printk("%s(%d): New cmdline '%s' at 0x%0lx\n", |
||||
__FUNCTION__, __LINE__, |
||||
t->u.cmdline.cmdline, (unsigned long)t->u.cmdline.cmdline); |
||||
|
||||
t = tag_next(t); |
||||
|
||||
printk("%s(%d): New end of table at 0x%0lx\n", __FUNCTION__, __LINE__, (unsigned long)t); |
||||
|
||||
t->hdr.tag = ATAG_NONE; |
||||
t->hdr.size = 0; |
||||
} |
||||
|
||||
/* Warning: Freecom uses their own custom bootloader with mach-type (=1500) */ |
||||
MACHINE_START(DT2, "Freecom DataTank Gateway") |
||||
/* Maintainer: Zintis Petersons <Zintis.Petersons@abcsolutions.lv> */ |
||||
.atag_offset = 0x100, |
||||
.init_machine = dt2_init, |
||||
.map_io = orion5x_map_io, |
||||
.init_irq = orion5x_init_irq, |
||||
.init_time = orion5x_timer_init, |
||||
.fixup = openwrt_fixup, //tag_fixup_mem32,
|
||||
MACHINE_END |
Loading…
Reference in new issue