imx6: update gw5400-a dts

- remove common imx6q-ventana.dtsi - there isn't enough commonality to
  warrent this
- rename user led's to 1-based
- add alises used by bootloader
- clean up iomux gpios
- fix pfuze slave address
- enable sata
- add delay after release of pci reset downstream from PCIe switch
- remove PCIe clock configuration as its now handled in updated driver

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 38081
master
Luka Perkov 11 years ago
parent 3f059f58db
commit c90e521790
  1. 104
      target/linux/imx6/files-3.10/arch/arm/boot/dts/imx6q-gw5400-a.dts
  2. 51
      target/linux/imx6/files-3.10/arch/arm/boot/dts/imx6q-ventana.dtsi
  3. 76
      target/linux/imx6/patches-3.10/110-gw5400-a.patch

@ -10,16 +10,43 @@
*/
/dts-v1/;
#include "imx6q-ventana.dtsi"
#include "imx6q.dtsi"
/ {
model = "Gateworks Ventana GW5400-A";
compatible = "gw,imx6q-gw5400-a", "gw,ventana", "fsl,imx6q";
/* these are used by bootloader for disabling nodes */
aliases {
ethernet0 = &fec;
ethernet1 = &eth1;
sky2 = &eth1;
ssi0 = &ssi1;
ssi1 = &ssi2;
ipu0 = &ipu1;
ipu1 = &ipu2;
usdhc0 = &usdhc1;
usdhc1 = &usdhc2;
usdhc2 = &usdhc3;
usdhc3 = &usdhc4;
i2c0 = &i2c1;
i2c1 = &i2c2;
i2c2 = &i2c3;
usb0 = &usbh3;
usb1 = &usbotg;
spi0 = &ecspi1;
spi1 = &ecspi2;
spi2 = &ecspi3;
spi3 = &ecspi4;
spi4 = &ecspi5;
pwm0 = &pwm1;
pwm1 = &pwm2;
pwm2 = &pwm3;
pwm3 = &pwm4;
can0 = &can1;
led0 = &led0;
led1 = &led1;
led2 = &led2;
};
/* SDRAM addressing */
@ -34,20 +61,23 @@
leds {
compatible = "gpio-leds";
led0: user0 {
label = "user0";
gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG# */
led0: user1 {
label = "user1";
gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */
default-state = "on";
linux,default-trigger = "heartbeat";
};
led1: user1 {
label = "user1";
gpios = <&gpio4 10 0>; /* 106 -> MX6_PANLEDR# */
led1: user2 {
label = "user2";
gpios = <&gpio4 10 0>; /* 106 -> MX6_PANLEDR */
default-state = "off";
};
led2: user2 {
label = "user2";
gpios = <&gpio4 15 0>; /* 111 -> MX6_LOCLEDR# */
led2: user3 {
label = "user3";
gpios = <&gpio4 15 1>; /* 111 -> MX6_LOCLED# */
default-state = "off";
};
};
@ -102,34 +132,23 @@
hog {
pinctrl_hog: hoggrp {
fsl,pins = <
/* USB OTG Power Enable */
MX6Q_PAD_EIM_D22__GPIO3_IO22 0x80000000
/* 3:19 SPINOR_CS0# */
MX6Q_PAD_EIM_D19__GPIO3_IO19 0x80000000
/* 1:09 MX6_DIO0 (could also be PWM1_PWM0) */
MX6Q_PAD_GPIO_9__GPIO1_IO09 0x80000000
/* 1:19 MX6_DIO1 (could also be PWM2_PWM0) */
MX6Q_PAD_SD1_DAT2__GPIO1_IO19 0x80000000
/* 2:09 MX6_DIO2 (could also be PWM3_PWM0) */
MX6Q_PAD_SD4_DAT1__GPIO2_IO09 0x80000000
/* 2:10 MX6_DIO3 (could also be PWM3_PWM0) */
MX6Q_PAD_SD4_DAT2__GPIO2_IO10 0x80000000
/* 1:16 USBHUB_RST# */
MX6Q_PAD_SD1_DAT0__GPIO1_IO16 0x80000000
/* PCIE IRQ */
MX6Q_PAD_ENET_TX_EN__GPIO1_IO28 0x80000000
/* PCIE RST */
MX6Q_PAD_ENET_TXD1__GPIO1_IO29 0x08000000
/* 1:12 MIPI_DIO */
MX6Q_PAD_SD1_DAT3__GPIO1_IO21 0x80000000
/* AUD4_MCK */
MX6Q_PAD_GPIO_0__CCM_CLKO1 0x80000000
MX6Q_PAD_EIM_D22__GPIO3_IO22 0x80000000 /* OTG_PWR_EN */
MX6Q_PAD_EIM_D19__GPIO3_IO19 0x80000000 /* SPINOR_CS0# */
MX6Q_PAD_KEY_COL0__GPIO4_IO06 0x80000000 /* user0 led */
MX6Q_PAD_KEY_COL2__GPIO4_IO10 0x80000000 /* user1 led */
MX6Q_PAD_KEY_ROW4__GPIO4_IO15 0x80000000 /* user2 led */
/* let bootloader choose these based on hwconfig */
#if 0
MX6Q_PAD_GPIO_9__GPIO1_IO09 0x80000000 /* MX6_DIO0 (or PWM1_PWM0) */
MX6Q_PAD_SD1_DAT2__GPIO1_IO19 0x80000000 /* MX6_DIO1 (or PWM2_PWM0) */
MX6Q_PAD_SD4_DAT1__GPIO2_IO09 0x80000000 /* MX6_DIO2 (or PWM3_PWM0) */
MX6Q_PAD_SD4_DAT2__GPIO2_IO10 0x80000000 /* MX6_DIO3 (or PWM3_PWM0) */
#endif
MX6Q_PAD_SD1_DAT0__GPIO1_IO16 0x80000000 /* USBHUB_RST# */
MX6Q_PAD_ENET_TX_EN__GPIO1_IO28 0x80000000 /* PCIE IRQ */
MX6Q_PAD_ENET_TXD1__GPIO1_IO29 0x08000000 /* PCIE RST */
MX6Q_PAD_SD1_DAT3__GPIO1_IO21 0x80000000 /* MIPI_DIO */
MX6Q_PAD_GPIO_0__CCM_CLKO1 0x80000000 /* AUD4_MCK */
>;
};
};
@ -262,7 +281,6 @@
&can1 {
reg = <0x02090000 0x4000>;
interrupts = <0 110 0x04>;
//clock-frequency
status = "okay";
};
@ -271,7 +289,7 @@
};
&pcie {
reset-gpios = <&gpio1 29 0>;
reset-gpio = <&gpio1 29 0>;
status = "okay";
eth1: sky2@8 { /* MAC/PHY on bus 8 */
@ -365,7 +383,7 @@
pmic: pfuze@08 {
compatible = "fsl,pfuze100";
reg = <0x0a>;
reg = <0x08>;
};
pciswitch: pex8609@3f {
@ -426,3 +444,7 @@
crtcs = <&ipu1 0>, <&ipu1 1>, <&ipu2 0>, <&ipu2 1>;
};
};
&sata {
status = "okay";
};

@ -1,51 +0,0 @@
/*
* Copyright 2013 Gateworks Corporation
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
#include "imx6q.dtsi"
/ {
model = "Gateworks Ventana";
system-serial = "";
// these are used by bootloader for disabling nodes
aliases {
// ethernet0 = &eth0;
// ethernet1 = &eth1;
ssi0 = &ssi1;
ssi1 = &ssi2;
ipu0 = &ipu1;
ipu1 = &ipu2;
// mipi_csi = &mipi_csi;
// mipi_dsi = &mipi_dsi;
usdhc0 = &usdhc1;
usdhc1 = &usdhc2;
usdhc2 = &usdhc3;
usdhc3 = &usdhc4;
i2c0 = &i2c1;
i2c1 = &i2c2;
i2c2 = &i2c3;
usb0 = &usbh3;
usb1 = &usbotg;
spi0 = &ecspi1;
spi1 = &ecspi2;
spi2 = &ecspi3;
spi3 = &ecspi4;
spi4 = &ecspi5;
pwm0 = &pwm1;
pwm1 = &pwm2;
pwm2 = &pwm3;
pwm3 = &pwm4;
can0 = &can1;
led0 = &led0;
led1 = &led1;
led2 = &led2;
};
};

@ -25,7 +25,38 @@
};
ecspi1 {
@@ -205,6 +213,12 @@
@@ -187,6 +195,30 @@
MX6Q_PAD_SD4_DAT0__NAND_DQS 0x00b1
>;
};
+
+ /* No strobe */
+ pinctrl_gpmi_nand_2: gpmi-nand-2 {
+ fsl,pins = <
+ MX6Q_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6Q_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6Q_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6Q_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6Q_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6Q_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6Q_PAD_NANDF_CS2__NAND_CE2_B 0xb0b1
+ MX6Q_PAD_NANDF_CS3__NAND_CE3_B 0xb0b1
+ MX6Q_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6Q_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6Q_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6Q_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6Q_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6Q_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6Q_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6Q_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6Q_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6Q_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
};
i2c1 {
@@ -205,6 +237,12 @@
MX6Q_PAD_EIM_D16__I2C2_SDA 0x4001b8b1
>;
};
@ -38,7 +69,7 @@
};
i2c3 {
@@ -214,6 +228,12 @@
@@ -214,6 +252,12 @@
MX6Q_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
>;
};
@ -51,7 +82,7 @@
};
uart1 {
@@ -223,6 +243,12 @@
@@ -223,6 +267,12 @@
MX6Q_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
>;
};
@ -64,7 +95,7 @@
};
uart2 {
@@ -232,6 +258,21 @@
@@ -232,6 +282,21 @@
MX6Q_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
>;
};
@ -86,7 +117,7 @@
};
uart4 {
@@ -242,6 +283,15 @@
@@ -242,6 +307,15 @@
>;
};
};
@ -112,7 +143,7 @@
#include <linux/phy.h>
#include <linux/regmap.h>
#include <linux/micrel_phy.h>
@@ -145,6 +146,65 @@ static void __init imx6q_sabrelite_init(
@@ -145,6 +146,38 @@ static void __init imx6q_sabrelite_init(
imx6q_sabrelite_cko1_setup();
}
@ -137,48 +168,21 @@
+ pci_read_config_dword(dev, 0x644, &dw);
+ dw |= 0xfe; // GPIO1-7 output high
+ pci_write_config_dword(dev, 0x644, dw);
+
+ mdelay(1);
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8609,
+ mx6_ventana_pciesw_early_fixup);
+
+/*
+ * configure PCIe core clock and PCIe ref clock
+ *
+ * TODO: disable CLK1 output and use CLK2 input from si52147 as PCIe ref
+ */
+static void __init imx6q_ventana_pcie_setup(void)
+{
+ struct clk *axi_sel, *axi, *ref;
+
+ axi_sel = clk_get_sys(NULL, "pcie_axi_sel");
+ axi = clk_get_sys(NULL, "axi");
+ ref = clk_get_sys(NULL, "pcie_ref_125m");
+ if (IS_ERR(axi_sel) || IS_ERR(axi) || IS_ERR(ref)) {
+ pr_err("pcie setup failed - can't get clocks\n");
+ goto put_clk;
+ }
+ clk_set_parent(axi_sel, axi);
+ clk_prepare_enable(ref);
+
+put_clk:
+ if (!IS_ERR(axi_sel))
+ clk_put(axi_sel);
+ if (!IS_ERR(axi))
+ clk_put(axi);
+ if (!IS_ERR(ref))
+ clk_put(ref);
+}
+
+static void __init imx6q_ventana_init(void)
+{
+ imx6q_ventana_pcie_setup();
+ imx6q_sabrelite_cko1_setup();
+}
+
static void __init imx6q_1588_init(void)
{
struct regmap *gpr;
@@ -163,6 +223,9 @@ static void __init imx6q_usb_init(void)
@@ -163,6 +196,9 @@ static void __init imx6q_usb_init(void)
static void __init imx6q_init_machine(void)
{

Loading…
Cancel
Save