kernel: ar83xx: Add support for three GMAC's connection

We have IPQ8064 AP161 board which has three GMAC's
 * RGMII x2
 * SGMII x1.
The existing ar8327 driver does not have support for
three GMAC's connection, hence this change adds support
for the same. This has been verified on AP148 and AP161
board.

Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
master
Ram Chandra Jangir 6 years ago committed by John Crispin
parent 99e212171a
commit bf7719f22c
  1. 15
      target/linux/generic/files/drivers/net/phy/ar8216.c
  2. 4
      target/linux/generic/files/drivers/net/phy/ar8216.h
  3. 44
      target/linux/generic/files/drivers/net/phy/ar8327.c
  4. 7
      target/linux/generic/files/drivers/net/phy/ar8327.h

@ -295,6 +295,17 @@ ar8xxx_rmw(struct ar8xxx_priv *priv, int reg, u32 mask, u32 val)
return ret;
}
void
ar8xxx_phy_dbg_read(struct ar8xxx_priv *priv, int phy_addr,
u16 dbg_addr, u16 *dbg_data)
{
struct mii_bus *bus = priv->mii_bus;
mutex_lock(&bus->mdio_lock);
bus->write(bus, phy_addr, MII_ATH_DBG_ADDR, dbg_addr);
*dbg_data = bus->read(bus, phy_addr, MII_ATH_DBG_DATA);
mutex_unlock(&bus->mdio_lock);
}
void
ar8xxx_phy_dbg_write(struct ar8xxx_priv *priv, int phy_addr,
@ -2166,7 +2177,7 @@ ar8xxx_phy_probe(struct phy_device *phydev)
int ret;
/* skip PHYs at unused adresses */
if (phydev->mdio.addr != 0 && phydev->mdio.addr != 4)
if (phydev->mdio.addr != 0 && phydev->mdio.addr != 3 && phydev->mdio.addr != 4)
return -ENODEV;
if (!ar8xxx_is_possible(phydev->mdio.bus))
@ -2225,6 +2236,8 @@ found:
phydev->supported |= SUPPORTED_1000baseT_Full;
phydev->advertising |= ADVERTISED_1000baseT_Full;
}
if (priv->chip->phy_rgmii_set)
priv->chip->phy_rgmii_set(priv, phydev);
}
phydev->priv = priv;

@ -413,6 +413,7 @@ struct ar8xxx_chip {
void (*get_arl_entry)(struct ar8xxx_priv *priv, struct arl_entry *a,
u32 *status, enum arl_op op);
int (*sw_hw_apply)(struct switch_dev *dev);
void (*phy_rgmii_set)(struct ar8xxx_priv *priv, struct phy_device *phydev);
const struct ar8xxx_mib_desc *mib_decs;
unsigned num_mibs;
@ -477,6 +478,9 @@ ar8xxx_write(struct ar8xxx_priv *priv, int reg, u32 val);
u32
ar8xxx_rmw(struct ar8xxx_priv *priv, int reg, u32 mask, u32 val);
void
ar8xxx_phy_dbg_read(struct ar8xxx_priv *priv, int phy_addr,
u16 dbg_addr, u16 *dbg_data);
void
ar8xxx_phy_dbg_write(struct ar8xxx_priv *priv, int phy_addr,
u16 dbg_addr, u16 dbg_data);

@ -127,6 +127,49 @@ ar8327_get_pad_cfg(struct ar8327_pad_cfg *cfg)
return t;
}
static void
ar8327_phy_rgmii_set(struct ar8xxx_priv *priv, struct phy_device *phydev)
{
u16 phy_val = 0;
int phyaddr = phydev->mdio.addr;
struct device_node *np = phydev->mdio.dev.of_node;
if (!np)
return;
if (!of_property_read_bool(np, "qca,phy-rgmii-en")) {
pr_err("ar8327: qca,phy-rgmii-en is not specified\n");
return -EINVAL;
}
ar8xxx_phy_dbg_read(priv, phyaddr,
AR8327_PHY_MODE_SEL, &phy_val);
phy_val |= AR8327_PHY_MODE_SEL_RGMII;
ar8xxx_phy_dbg_write(priv, phyaddr,
AR8327_PHY_MODE_SEL, phy_val);
/* set rgmii tx clock delay if needed */
if (!of_property_read_bool(np, "qca,txclk-delay-en")) {
pr_err("ar8327: qca,txclk-delay-en is not specified\n");
return -EINVAL;
}
ar8xxx_phy_dbg_read(priv, phyaddr,
AR8327_PHY_SYS_CTRL, &phy_val);
phy_val |= AR8327_PHY_SYS_CTRL_RGMII_TX_DELAY;
ar8xxx_phy_dbg_write(priv, phyaddr,
AR8327_PHY_SYS_CTRL, phy_val);
/* set rgmii rx clock delay if needed */
if (!of_property_read_bool(np, "qca,rxclk-delay-en")) {
pr_err("ar8327: qca,rxclk-delay-en is not specified\n");
return -EINVAL;
}
ar8xxx_phy_dbg_read(priv, phyaddr,
AR8327_PHY_TEST_CTRL, &phy_val);
phy_val |= AR8327_PHY_TEST_CTRL_RGMII_RX_DELAY;
ar8xxx_phy_dbg_write(priv, phyaddr,
AR8327_PHY_TEST_CTRL, phy_val);
}
static void
ar8327_phy_fixup(struct ar8xxx_priv *priv, int phy)
{
@ -1490,6 +1533,7 @@ const struct ar8xxx_chip ar8337_chip = {
.set_mirror_regs = ar8327_set_mirror_regs,
.get_arl_entry = ar8327_get_arl_entry,
.sw_hw_apply = ar8327_sw_hw_apply,
.phy_rgmii_set = ar8327_phy_rgmii_set,
.num_mibs = ARRAY_SIZE(ar8236_mibs),
.mib_decs = ar8236_mibs,

@ -284,6 +284,13 @@
#define AR8337_PAD_MAC06_EXCHANGE_EN BIT(31)
#define AR8327_PHY_MODE_SEL 0x12
#define AR8327_PHY_MODE_SEL_RGMII BIT(3)
#define AR8327_PHY_TEST_CTRL 0x0
#define AR8327_PHY_TEST_CTRL_RGMII_RX_DELAY BIT(15)
#define AR8327_PHY_SYS_CTRL 0x5
#define AR8327_PHY_SYS_CTRL_RGMII_TX_DELAY BIT(8)
enum ar8327_led_pattern {
AR8327_LED_PATTERN_OFF = 0,
AR8327_LED_PATTERN_BLINK,

Loading…
Cancel
Save