ar71xx: add support for TP-Link TL-WR942N v1

TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*

* Serial console is disabled in OEM non-beta firmwares and corresponding
  GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
  production (non-beta) U-Boot and firmware.

Currently not working:

1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
   by some U-Boot versions.

Flash instruction under vendor GUI:

1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.

FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):

1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
   it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
   turns on.

Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):

1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
   tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
   erase 0x9f020000 +$filesize
   cp.b 0x81000000 0x9f020000 $filesize
   reset

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
master
Serg Studzinskii 8 years ago committed by Piotr Dymacz
parent 641af0c39d
commit b7cc661615
  1. 10
      target/linux/ar71xx/base-files/etc/board.d/01_leds
  2. 3
      target/linux/ar71xx/base-files/etc/board.d/02_network
  3. 1
      target/linux/ar71xx/base-files/etc/diag.sh
  4. 3
      target/linux/ar71xx/base-files/lib/ar71xx.sh
  5. 1
      target/linux/ar71xx/base-files/lib/upgrade/platform.sh
  6. 1
      target/linux/ar71xx/config-4.4
  7. 11
      target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
  8. 1
      target/linux/ar71xx/files/arch/mips/ath79/Makefile
  9. 279
      target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wr942n-v1.c
  10. 1
      target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
  11. 7
      target/linux/ar71xx/files/arch/mips/ath79/nvram.c
  12. 15
      target/linux/ar71xx/image/tp-link.mk
  13. 1
      target/linux/ar71xx/mikrotik/config-default
  14. 1
      target/linux/ar71xx/nand/config-default
  15. 37
      tools/firmware-utils/src/tplink-safeloader.c

@ -745,6 +745,16 @@ tl-wr840n-v3)
ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x1E" ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x1E"
ucidef_set_led_wlan "wlan" "WLAN" "tp-link:green:wlan" "phy0tpt" ucidef_set_led_wlan "wlan" "WLAN" "tp-link:green:wlan" "phy0tpt"
;; ;;
tl-wr942n-v1)
ucidef_set_led_switch "lan1" "LAN1" "$board:green:lan1" "switch0" "0x04"
ucidef_set_led_switch "lan2" "LAN2" "$board:green:lan2" "switch0" "0x08"
ucidef_set_led_switch "lan3" "LAN3" "$board:green:lan3" "switch0" "0x10"
ucidef_set_led_switch "lan4" "LAN4" "$board:green:lan4" "switch0" "0x02"
ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth0"
ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt"
ucidef_set_led_usbdev "usb1" "USB1" "$board:green:usb1" "1-1.2"
ucidef_set_led_usbdev "usb2" "USB2" "$board:green:usb2" "1-1.1"
;;
tl-wr1043nd|\ tl-wr1043nd|\
tl-wr1043nd-v2) tl-wr1043nd-v2)
ucidef_set_led_usbdev "usb" "USB" "tp-link:green:usb" "1-1" ucidef_set_led_usbdev "usb" "USB" "tp-link:green:usb" "1-1"

@ -411,7 +411,8 @@ ar71xx_setup_interfaces()
tl-mr3420-v2|\ tl-mr3420-v2|\
tl-wr841n-v8|\ tl-wr841n-v8|\
tl-wr842n-v2|\ tl-wr842n-v2|\
tl-wr941nd-v5) tl-wr941nd-v5|\
tl-wr942n-v1)
ucidef_set_interfaces_lan_wan "eth1.1" "eth0" ucidef_set_interfaces_lan_wan "eth1.1" "eth0"
ucidef_add_switch "switch0" \ ucidef_add_switch "switch0" \
"0@eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3" "0@eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"

@ -36,6 +36,7 @@ get_status_led() {
db120|\ db120|\
dr344|\ dr344|\
tew-632brp|\ tew-632brp|\
tl-wr942n-v1|\
wpj344|\ wpj344|\
zbt-we1526) zbt-we1526)
status_led="$board:green:status" status_led="$board:green:status"

@ -1166,6 +1166,9 @@ ar71xx_board_detect() {
*"TL-WR941ND") *"TL-WR941ND")
name="tl-wr941nd" name="tl-wr941nd"
;; ;;
*"TL-WR942N v1")
name="tl-wr942n-v1"
;;
*"Tube2H") *"Tube2H")
name="tube2h" name="tube2h"
;; ;;

@ -271,6 +271,7 @@ platform_check_image() {
tew-712br|\ tew-712br|\
tew-732br|\ tew-732br|\
tew-823dru|\ tew-823dru|\
tl-wr942n-v1|\
unifi-outdoor|\ unifi-outdoor|\
unifiac-lite|\ unifiac-lite|\
unifiac-pro|\ unifiac-pro|\

@ -209,6 +209,7 @@ CONFIG_ATH79_MACH_TL_WR841N_V9=y
CONFIG_ATH79_MACH_TL_WR941ND=y CONFIG_ATH79_MACH_TL_WR941ND=y
CONFIG_ATH79_MACH_TL_WR941ND_V6=y CONFIG_ATH79_MACH_TL_WR941ND_V6=y
CONFIG_ATH79_MACH_TL_WR940N_V4=y CONFIG_ATH79_MACH_TL_WR940N_V4=y
CONFIG_ATH79_MACH_TL_WR942N_V1=y
CONFIG_ATH79_MACH_TUBE2H=y CONFIG_ATH79_MACH_TUBE2H=y
CONFIG_ATH79_MACH_UBNT=y CONFIG_ATH79_MACH_UBNT=y
CONFIG_ATH79_MACH_UBNT_UNIFIAC=y CONFIG_ATH79_MACH_UBNT_UNIFIAC=y

@ -1695,6 +1695,17 @@ config ATH79_MACH_TL_WR940N_V4
select ATH79_DEV_M25P80 select ATH79_DEV_M25P80
select ATH79_DEV_WMAC select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR942N_V1
bool "TP-LINK TL-WR942N v1 support"
select SOC_QCA956X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_TL_WR1041N_V2 config ATH79_MACH_TL_WR1041N_V2
bool "TP-LINK TL-WR1041N v2 support" bool "TP-LINK TL-WR1041N v2 support"
select SOC_AR934X select SOC_AR934X

@ -214,6 +214,7 @@ obj-$(CONFIG_ATH79_MACH_TL_WR841N_V9) += mach-tl-wr841n-v9.o
obj-$(CONFIG_ATH79_MACH_TL_WR941ND) += mach-tl-wr941nd.o obj-$(CONFIG_ATH79_MACH_TL_WR941ND) += mach-tl-wr941nd.o
obj-$(CONFIG_ATH79_MACH_TL_WR941ND_V6) += mach-tl-wr941nd-v6.o obj-$(CONFIG_ATH79_MACH_TL_WR941ND_V6) += mach-tl-wr941nd-v6.o
obj-$(CONFIG_ATH79_MACH_TL_WR940N_V4) += mach-tl-wr940n-v4.o obj-$(CONFIG_ATH79_MACH_TL_WR940N_V4) += mach-tl-wr940n-v4.o
obj-$(CONFIG_ATH79_MACH_TL_WR942N_V1) += mach-tl-wr942n-v1.o
obj-$(CONFIG_ATH79_MACH_TUBE2H) += mach-tube2h.o obj-$(CONFIG_ATH79_MACH_TUBE2H) += mach-tube2h.o
obj-$(CONFIG_ATH79_MACH_UBNT) += mach-ubnt.o obj-$(CONFIG_ATH79_MACH_UBNT) += mach-ubnt.o
obj-$(CONFIG_ATH79_MACH_UBNT_UNIFIAC) += mach-ubnt-unifiac.o obj-$(CONFIG_ATH79_MACH_UBNT_UNIFIAC) += mach-ubnt-unifiac.o

@ -0,0 +1,279 @@
/*
* TP-Link TL-WR942N(RU) v1 board support
*
* Copyright (C) 2017 Sergey Studzinski <serguzhg@gmail.com>
* Thanks to Henryk Heisig <hyniu@o2.pl>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published
* by the Free Software Foundation.
*/
#include <linux/platform_device.h>
#include <linux/ath9k_platform.h>
#include <asm/mach-ath79/ar71xx_regs.h>
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/spi/spi_gpio.h>
#include <linux/spi/74x164.h>
#include "common.h"
#include "dev-m25p80.h"
#include "machtypes.h"
#include "dev-eth.h"
#include "dev-gpio-buttons.h"
#include "dev-leds-gpio.h"
#include "dev-spi.h"
#include "dev-usb.h"
#include "dev-wmac.h"
#include "nvram.h"
#define TL_WR942N_V1_KEYS_POLL_INTERVAL 20
#define TL_WR942N_V1_KEYS_DEBOUNCE_INTERVAL \
(3 * TL_WR942N_V1_KEYS_POLL_INTERVAL)
#define TL_WR942N_V1_GPIO_BTN_RESET 1
#define TL_WR942N_V1_GPIO_BTN_RFKILL 2
#define TL_WR942N_V1_GPIO_UART_TX 4
#define TL_WR942N_V1_GPIO_UART_RX 5
#define TL_WR942N_V1_GPIO_LED_USB2 14
#define TL_WR942N_V1_GPIO_LED_USB1 15
#define TL_WR942N_V1_GPIO_SHIFT_OE 16
#define TL_WR942N_V1_GPIO_SHIFT_SER 17
#define TL_WR942N_V1_GPIO_SHIFT_SRCLK 18
#define TL_WR942N_V1_GPIO_SHIFT_SRCLR 19
#define TL_WR942N_V1_GPIO_SHIFT_RCLK 20
#define TL_WR942N_V1_GPIO_LED_WPS 21
#define TL_WR942N_V1_GPIO_LED_STATUS 22
#define TL_WR942N_V1_74HC_GPIO_BASE QCA956X_GPIO_COUNT
#define TL_WR942N_V1_74HC_GPIO_LED_LAN4 23
#define TL_WR942N_V1_74HC_GPIO_LED_LAN3 24
#define TL_WR942N_V1_74HC_GPIO_LED_LAN2 25
#define TL_WR942N_V1_74HC_GPIO_LED_LAN1 26
#define TL_WR942N_V1_74HC_GPIO_LED_WAN_GREEN 27
#define TL_WR942N_V1_74HC_GPIO_LED_WAN_AMBER 28
#define TL_WR942N_V1_74HC_GPIO_LED_WLAN 29
#define TL_WR942N_V1_74HC_GPIO_HUB_RESET 30 /* from u-boot sources */
#define TL_WR942N_V1_SSR_BIT_0 0
#define TL_WR942N_V1_SSR_BIT_1 1
#define TL_WR942N_V1_SSR_BIT_2 2
#define TL_WR942N_V1_SSR_BIT_3 3
#define TL_WR942N_V1_SSR_BIT_4 4
#define TL_WR942N_V1_SSR_BIT_5 5
#define TL_WR942N_V1_SSR_BIT_6 6
#define TL_WR942N_V1_SSR_BIT_7 7
#define TL_WR942N_V1_WMAC_CALDATA_OFFSET 0x1000
#define TL_WR942N_V1_DEFAULT_MAC_ADDR 0x1fe40008
#define TL_WR942N_V1_DEFAULT_MAC_SIZE 0x200
#define GPIO_IN_ENABLE0_UART_SIN_LSB 8
#define GPIO_IN_ENABLE0_UART_SIN_MASK 0x0000ff00
static struct gpio_led tl_wr942n_v1_leds_gpio[] __initdata = {
{
.name = "tl-wr942n-v1:green:status",
.gpio = TL_WR942N_V1_GPIO_LED_STATUS,
.active_low = 1,
}, {
.name = "tl-wr942n-v1:green:wlan",
.gpio = TL_WR942N_V1_74HC_GPIO_LED_WLAN,
.active_low = 1,
}, {
.name = "tl-wr942n-v1:green:lan1",
.gpio = TL_WR942N_V1_74HC_GPIO_LED_LAN1,
.active_low = 1,
}, {
.name = "tl-wr942n-v1:green:lan2",
.gpio = TL_WR942N_V1_74HC_GPIO_LED_LAN2,
.active_low = 1,
}, {
.name = "tl-wr942n-v1:green:lan3",
.gpio = TL_WR942N_V1_74HC_GPIO_LED_LAN3,
.active_low = 1,
}, {
.name = "tl-wr942n-v1:green:lan4",
.gpio = TL_WR942N_V1_74HC_GPIO_LED_LAN4,
.active_low = 1,
}, {
.name = "tl-wr942n-v1:green:wan",
.gpio = TL_WR942N_V1_74HC_GPIO_LED_WAN_GREEN,
.active_low = 1,
}, {
.name = "tl-wr942n-v1:amber:wan",
.gpio = TL_WR942N_V1_74HC_GPIO_LED_WAN_AMBER,
.active_low = 1,
}, {
.name = "tl-wr942n-v1:green:wps",
.gpio = TL_WR942N_V1_GPIO_LED_WPS,
.active_low = 1,
}, {
.name = "tl-wr942n-v1:green:usb1",
.gpio = TL_WR942N_V1_GPIO_LED_USB1,
.active_low = 1,
}, {
.name = "tl-wr942n-v1:green:usb2",
.gpio = TL_WR942N_V1_GPIO_LED_USB2,
.active_low = 1,
},
};
static struct gpio_keys_button tl_wr942n_v1_gpio_keys[] __initdata = {
{
.desc = "Reset button",
.type = EV_KEY,
.code = KEY_RESTART,
.debounce_interval = TL_WR942N_V1_KEYS_DEBOUNCE_INTERVAL,
.gpio = TL_WR942N_V1_GPIO_BTN_RESET,
.active_low = 1,
}, {
.desc = "RFKILL button",
.type = EV_KEY,
.code = KEY_RFKILL,
.debounce_interval = TL_WR942N_V1_KEYS_DEBOUNCE_INTERVAL,
.gpio = TL_WR942N_V1_GPIO_BTN_RFKILL,
.active_low = 1,
},
};
static struct spi_gpio_platform_data tl_wr942n_v1_spi_data = {
.sck = TL_WR942N_V1_GPIO_SHIFT_SRCLK,
.miso = SPI_GPIO_NO_MISO,
.mosi = TL_WR942N_V1_GPIO_SHIFT_SER,
.num_chipselect = 1,
};
static u8 tl_wr942n_v1_ssr_initdata[] __initdata = {
BIT(TL_WR942N_V1_SSR_BIT_7) |
BIT(TL_WR942N_V1_SSR_BIT_6) |
BIT(TL_WR942N_V1_SSR_BIT_5) |
BIT(TL_WR942N_V1_SSR_BIT_4) |
BIT(TL_WR942N_V1_SSR_BIT_3) |
BIT(TL_WR942N_V1_SSR_BIT_2) |
BIT(TL_WR942N_V1_SSR_BIT_1) |
BIT(TL_WR942N_V1_SSR_BIT_0)
};
static struct gen_74x164_chip_platform_data tl_wr942n_v1_ssr_data = {
.base = TL_WR942N_V1_74HC_GPIO_BASE,
.num_registers = ARRAY_SIZE(tl_wr942n_v1_ssr_initdata),
.init_data = tl_wr942n_v1_ssr_initdata,
};
static struct platform_device tl_wr942n_v1_spi_device = {
.name = "spi_gpio",
.id = 1,
.dev = {
.platform_data = &tl_wr942n_v1_spi_data,
},
};
static struct spi_board_info tl_wr942n_v1_spi_info[] = {
{
.bus_num = 1,
.chip_select = 0,
.max_speed_hz = 10000000,
.modalias = "74x164",
.platform_data = &tl_wr942n_v1_ssr_data,
.controller_data = (void *) TL_WR942N_V1_GPIO_SHIFT_RCLK,
},
};
static void tl_wr942n_v1_get_mac(const char *name, char *mac)
{
u8 *nvram = (u8 *) KSEG1ADDR(TL_WR942N_V1_DEFAULT_MAC_ADDR);
int err;
err = ath79_nvram_parse_mac_addr(nvram, TL_WR942N_V1_DEFAULT_MAC_SIZE,
name, mac);
if (err)
pr_err("no MAC address found for %s\n", name);
}
static void __init tl_wr942n_v1_setup(void)
{
u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
u8 tmpmac[ETH_ALEN];
void __iomem *base;
u32 t;
ath79_register_m25p80(NULL);
spi_register_board_info(tl_wr942n_v1_spi_info,
ARRAY_SIZE(tl_wr942n_v1_spi_info));
platform_device_register(&tl_wr942n_v1_spi_device);
/* Check inherited UART RX GPIO definition */
base = ioremap(AR71XX_GPIO_BASE, AR71XX_GPIO_SIZE);
t = __raw_readl(base + QCA956X_GPIO_REG_IN_ENABLE0);
if (((t & GPIO_IN_ENABLE0_UART_SIN_MASK)
>> GPIO_IN_ENABLE0_UART_SIN_LSB) == TL_WR942N_V1_GPIO_LED_USB1) {
pr_warn("Active UART detected on USBLED's GPIOs!\n");
tl_wr942n_v1_leds_gpio[9].gpio = TL_WR942N_V1_GPIO_UART_TX;
tl_wr942n_v1_leds_gpio[10].gpio = TL_WR942N_V1_GPIO_UART_RX;
}
ath79_register_leds_gpio(-1, ARRAY_SIZE(tl_wr942n_v1_leds_gpio),
tl_wr942n_v1_leds_gpio);
ath79_register_gpio_keys_polled(-1, TL_WR942N_V1_KEYS_POLL_INTERVAL,
ARRAY_SIZE(tl_wr942n_v1_gpio_keys),
tl_wr942n_v1_gpio_keys);
tl_wr942n_v1_get_mac("MAC:", tmpmac);
/* swap PHYs */
ath79_setup_qca956x_eth_cfg(QCA956X_ETH_CFG_SW_PHY_SWAP |
QCA956X_ETH_CFG_SW_PHY_ADDR_SWAP);
ath79_register_mdio(0, 0x0);
ath79_register_mdio(1, 0x0);
/* WAN port */
ath79_init_mac(ath79_eth0_data.mac_addr, tmpmac, 1);
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
ath79_eth0_data.speed = SPEED_100;
ath79_eth0_data.duplex = DUPLEX_FULL;
/* swaped PHYs */
ath79_eth0_data.phy_mask = BIT(0);
ath79_register_eth(0);
/* LAN ports */
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
ath79_init_mac(ath79_eth1_data.mac_addr, tmpmac, 0);
ath79_eth1_data.speed = SPEED_1000;
ath79_eth1_data.duplex = DUPLEX_FULL;
/* swaped PHYs */
ath79_switch_data.phy_poll_mask |= BIT(0);
ath79_switch_data.phy4_mii_en = 1;
ath79_register_eth(1);
ath79_register_wmac(art + TL_WR942N_V1_WMAC_CALDATA_OFFSET, tmpmac);
ath79_register_usb();
gpio_request_one(TL_WR942N_V1_74HC_GPIO_HUB_RESET,
GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
"USB power");
gpio_request_one(TL_WR942N_V1_GPIO_SHIFT_OE,
GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED,
"LED control");
gpio_request_one(TL_WR942N_V1_GPIO_SHIFT_SRCLR,
GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
"LED reset");
}
MIPS_MACHINE(ATH79_MACH_TL_WR942N_V1, "TL-WR942N-V1", "TP-LINK TL-WR942N v1",
tl_wr942n_v1_setup);

@ -262,6 +262,7 @@ enum ath79_mach_type {
ATH79_MACH_TL_WR941ND_V5, /* TP-LINK TL-WR941ND v5 */ ATH79_MACH_TL_WR941ND_V5, /* TP-LINK TL-WR941ND v5 */
ATH79_MACH_TL_WR941ND_V6, /* TP-LINK TL-WR941ND v6 */ ATH79_MACH_TL_WR941ND_V6, /* TP-LINK TL-WR941ND v6 */
ATH79_MACH_TL_WR940N_V4, /* TP-LINK TL-WR940N v4 */ ATH79_MACH_TL_WR940N_V4, /* TP-LINK TL-WR940N v4 */
ATH79_MACH_TL_WR942N_V1, /* TP-LINK TL-WR942N v1 */
ATH79_MACH_TUBE2H, /* Alfa Network Tube2H */ ATH79_MACH_TUBE2H, /* Alfa Network Tube2H */
ATH79_MACH_UBNT_AIRGW, /* Ubiquiti AirGateway */ ATH79_MACH_UBNT_AIRGW, /* Ubiquiti AirGateway */
ATH79_MACH_UBNT_AIRGWP, /* Ubiquiti AirGateway Pro */ ATH79_MACH_UBNT_AIRGWP, /* Ubiquiti AirGateway Pro */

@ -13,6 +13,7 @@
#include <linux/errno.h> #include <linux/errno.h>
#include <linux/init.h> #include <linux/init.h>
#include <linux/string.h> #include <linux/string.h>
#include <linux/etherdevice.h>
#include "nvram.h" #include "nvram.h"
@ -67,7 +68,11 @@ int ath79_nvram_parse_mac_addr(const char *nvram, unsigned nvram_len,
t = sscanf(mac_str, "%02hhx:%02hhx:%02hhx:%02hhx:%02hhx:%02hhx", t = sscanf(mac_str, "%02hhx:%02hhx:%02hhx:%02hhx:%02hhx:%02hhx",
&mac[0], &mac[1], &mac[2], &mac[3], &mac[4], &mac[5]); &mac[0], &mac[1], &mac[2], &mac[3], &mac[4], &mac[5]);
if (t != 6) { if (t != ETH_ALEN)
t = sscanf(mac_str, "%02hhx-%02hhx-%02hhx-%02hhx-%02hhx-%02hhx",
&mac[0], &mac[1], &mac[2], &mac[3], &mac[4], &mac[5]);
if (t != ETH_ALEN) {
ret = -EINVAL; ret = -EINVAL;
goto free; goto free;
} }

@ -873,6 +873,21 @@ define Device/tl-wr941nd-v6-cn
endef endef
TARGET_DEVICES += tl-wr941nd-v2 tl-wr941nd-v3 tl-wr941nd-v4 tl-wr941nd-v5 tl-wr941nd-v6 tl-wr941nd-v6-cn tl-wr940n-v4 TARGET_DEVICES += tl-wr941nd-v2 tl-wr941nd-v3 tl-wr941nd-v4 tl-wr941nd-v5 tl-wr941nd-v6 tl-wr941nd-v6-cn tl-wr940n-v4
define Device/tl-wr942n-v1
DEVICE_TITLE := TP-LINK TL-WR942N v1
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
BOARDNAME := TL-WR942N-V1
TPLINK_BOARD_NAME := TLWR942NV1
DEVICE_PROFILE := TLWR942
IMAGE_SIZE := 14464k
KERNEL := kernel-bin | patch-cmdline | lzma | uImageArcher lzma
IMAGES := sysupgrade.bin factory.bin
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
MTDPARTS := spi0.0:128k(u-boot)ro,1344k(kernel),13120k(rootfs),64k(product-info)ro,64k(partition-table)ro,256k(oem-config)ro,1344k(oem-vars)ro,64k(ART)ro,14464k@0x20000(firmware)
endef
TARGET_DEVICES += tl-wr942n-v1
define Device/tl-wr1041n-v2 define Device/tl-wr1041n-v2
$(Device/tplink-4mlzma) $(Device/tplink-4mlzma)
DEVICE_TITLE := TP-LINK TL-WR1041N v2 DEVICE_TITLE := TP-LINK TL-WR1041N v2

@ -172,6 +172,7 @@ CONFIG_ATH79_MACH_RBSXTLITE=y
# CONFIG_ATH79_MACH_TL_WR940N_V4 is not set # CONFIG_ATH79_MACH_TL_WR940N_V4 is not set
# CONFIG_ATH79_MACH_TL_WR941ND is not set # CONFIG_ATH79_MACH_TL_WR941ND is not set
# CONFIG_ATH79_MACH_TL_WR941ND_V6 is not set # CONFIG_ATH79_MACH_TL_WR941ND_V6 is not set
# CONFIG_ATH79_MACH_TL_WR942N_V1 is not set
# CONFIG_ATH79_MACH_TUBE2H is not set # CONFIG_ATH79_MACH_TUBE2H is not set
# CONFIG_ATH79_MACH_UBNT is not set # CONFIG_ATH79_MACH_UBNT is not set
# CONFIG_ATH79_MACH_UBNT_UNIFIAC is not set # CONFIG_ATH79_MACH_UBNT_UNIFIAC is not set

@ -160,6 +160,7 @@ CONFIG_ATH79_MACH_RAMBUTAN=y
# CONFIG_ATH79_MACH_TL_WR940N_V4 is not set # CONFIG_ATH79_MACH_TL_WR940N_V4 is not set
# CONFIG_ATH79_MACH_TL_WR941ND is not set # CONFIG_ATH79_MACH_TL_WR941ND is not set
# CONFIG_ATH79_MACH_TL_WR941ND_V6 is not set # CONFIG_ATH79_MACH_TL_WR941ND_V6 is not set
# CONFIG_ATH79_MACH_TL_WR942N_V1 is not set
# CONFIG_ATH79_MACH_TUBE2H is not set # CONFIG_ATH79_MACH_TUBE2H is not set
# CONFIG_ATH79_MACH_UBNT is not set # CONFIG_ATH79_MACH_UBNT is not set
# CONFIG_ATH79_MACH_UBNT_UNIFIAC is not set # CONFIG_ATH79_MACH_UBNT_UNIFIAC is not set

@ -553,6 +553,43 @@ static struct device_info boards[] = {
.last_sysupgrade_partition = "file-system" .last_sysupgrade_partition = "file-system"
}, },
/** Firmware layout for the TL-WR942N V1 */
{
.id = "TLWR942NV1",
.vendor = "",
.support_list =
"SupportList:\r\n"
"{product_name:TL-WR942N,product_ver:1.0.0,special_id:00000000}\r\n"
"{product_name:TL-WR942N,product_ver:1.0.0,special_id:52550000}\r\n",
.support_trail = '\x00',
.soft_ver = NULL,
.partitions = {
{"fs-uboot", 0x00000, 0x20000},
{"os-image", 0x20000, 0x150000},
{"file-system", 0x170000, 0xcd0000},
{"default-mac", 0xe40000, 0x00200},
{"pin", 0xe40200, 0x00200},
{"product-info", 0xe40400, 0x0fc00},
{"partition-table", 0xe50000, 0x10000},
{"soft-version", 0xe60000, 0x10000},
{"support-list", 0xe70000, 0x10000},
{"profile", 0xe80000, 0x10000},
{"default-config", 0xe90000, 0x10000},
{"user-config", 0xea0000, 0x40000},
{"qos-db", 0xee0000, 0x40000},
{"certificate", 0xf20000, 0x10000},
{"usb-config", 0xfb0000, 0x10000},
{"log", 0xfc0000, 0x20000},
{"radio-bk", 0xfe0000, 0x10000},
{"radio", 0xff0000, 0x10000},
{NULL, 0, 0}
},
.first_sysupgrade_partition = "os-image",
.last_sysupgrade_partition = "file-system",
},
/** Firmware layout for the RE450 */ /** Firmware layout for the RE450 */
{ {
.id = "RE450", .id = "RE450",

Loading…
Cancel
Save