The HNET C108 (http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a mifi based on MT7602A, which has the following specifications: * CPU: MT7620A * 1x 10/100Mbps Ethernet. * 16 MB Flash. * 64 MB RAM. * 1x USB 2.0 port. Only power is connected, this port is meant for charging other devices. * 1x mini-PCIe slots. * 1x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. * 6000 mAh battery. * 5x controllable LEDs. Works: * Wifi. * Switch. * mini-PCIe slot. Only tested with a USB device (a modem). * SIM slot. * Sysupgrade. * Button (reset). Not working (also applies to the factory firmware): * Wifi LED. It is always switched on, there is no relation to the up/down state or activity of the wireless interface. Not tested: * SD card reader. Notes: * The C108 has no dedicated status LED. I therefore set the LAN LED as status LED. Installation: The router comes pre-installed with OpenWRT, including a variant of Luci. The initial firmware install can be done through this UI, following normal procedure. I.e., access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. Recovery: If you brick the device, the C108 supports recovery using TFTP. Keep the reset button pressed for ~5sec when booting to trigger TFTP. Set the address of the network interface on your machine to 10.10.10.3/24, and rename your image file to Kernal.bin. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>master
parent
096dff8fcd
commit
80829022b0
@ -0,0 +1,177 @@ |
|||||||
|
/* |
||||||
|
* BSD LICENSE |
||||||
|
* |
||||||
|
* Copyright(c) 2017 Kristian Evensen <kristian.evensen@gmail.com>. |
||||||
|
* All rights reserved. |
||||||
|
* |
||||||
|
* Redistribution and use in source and binary forms, with or without |
||||||
|
* modification, are permitted provided that the following conditions |
||||||
|
* are met: |
||||||
|
* |
||||||
|
* * Redistributions of source code must retain the above copyright |
||||||
|
* notice, this list of conditions and the following disclaimer. |
||||||
|
* * Redistributions in binary form must reproduce the above copyright |
||||||
|
* notice, this list of conditions and the following disclaimer in |
||||||
|
* the documentation and/or other materials provided with the |
||||||
|
* distribution. |
||||||
|
* * Neither the name of Broadcom Corporation nor the names of its |
||||||
|
* contributors may be used to endorse or promote products derived |
||||||
|
* from this software without specific prior written permission. |
||||||
|
* |
||||||
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS |
||||||
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT |
||||||
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR |
||||||
|
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT |
||||||
|
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, |
||||||
|
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT |
||||||
|
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, |
||||||
|
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY |
||||||
|
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT |
||||||
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE |
||||||
|
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
||||||
|
*/ |
||||||
|
|
||||||
|
/dts-v1/; |
||||||
|
|
||||||
|
#include "mt7620a.dtsi" |
||||||
|
|
||||||
|
#include <dt-bindings/gpio/gpio.h> |
||||||
|
#include <dt-bindings/input/input.h> |
||||||
|
|
||||||
|
/ { |
||||||
|
compatible = "hnet,c108", "ralink,mt7620a-soc"; |
||||||
|
model = "HNET C108"; |
||||||
|
|
||||||
|
chosen { |
||||||
|
bootargs = "console=ttyS0,115200"; |
||||||
|
}; |
||||||
|
|
||||||
|
gpio-export { |
||||||
|
compatible = "gpio-export"; |
||||||
|
#size-cells = <0>; |
||||||
|
|
||||||
|
power_modem { |
||||||
|
gpio-export,name = "power_modem"; |
||||||
|
gpio-export,output = <1>; |
||||||
|
gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
gpio-leds { |
||||||
|
compatible = "gpio-leds"; |
||||||
|
|
||||||
|
sdcard { |
||||||
|
label = "c108:green:sdcard"; |
||||||
|
gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; |
||||||
|
}; |
||||||
|
|
||||||
|
modem_green { |
||||||
|
label = "c108:green:modem"; |
||||||
|
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; |
||||||
|
}; |
||||||
|
|
||||||
|
modem_red { |
||||||
|
label = "c108:red:modem"; |
||||||
|
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; |
||||||
|
}; |
||||||
|
|
||||||
|
lan_red { |
||||||
|
label = "c108:red:lan"; |
||||||
|
gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>; |
||||||
|
}; |
||||||
|
|
||||||
|
lan_green { |
||||||
|
label = "c108:green:lan"; |
||||||
|
gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
gpio-keys-polled { |
||||||
|
compatible = "gpio-keys-polled"; |
||||||
|
#address-cells = <1>; |
||||||
|
#size-cells = <0>; |
||||||
|
poll-interval = <20>; |
||||||
|
|
||||||
|
reset { |
||||||
|
label = "reset"; |
||||||
|
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
||||||
|
linux,code = <KEY_RESTART>; |
||||||
|
}; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
&gpio1 { |
||||||
|
status = "okay"; |
||||||
|
}; |
||||||
|
|
||||||
|
&gpio2 { |
||||||
|
status = "okay"; |
||||||
|
}; |
||||||
|
|
||||||
|
&spi0 { |
||||||
|
status = "okay"; |
||||||
|
|
||||||
|
en25q128@0 { |
||||||
|
#address-cells = <1>; |
||||||
|
#size-cells = <1>; |
||||||
|
compatible = "jedec,spi-nor"; |
||||||
|
reg = <0>; |
||||||
|
spi-max-frequency = <10000000>; |
||||||
|
|
||||||
|
partition@0 { |
||||||
|
label = "u-boot"; |
||||||
|
reg = <0x0 0x30000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
partition@30000 { |
||||||
|
label = "u-boot-env"; |
||||||
|
reg = <0x30000 0x10000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
factory: partition@40000 { |
||||||
|
label = "factory"; |
||||||
|
reg = <0x40000 0x10000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
partition@50000 { |
||||||
|
label = "firmware"; |
||||||
|
reg = <0x50000 0xfb0000>; |
||||||
|
}; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
&sdhci { |
||||||
|
status = "okay"; |
||||||
|
}; |
||||||
|
|
||||||
|
&ehci { |
||||||
|
status = "okay"; |
||||||
|
}; |
||||||
|
|
||||||
|
&ohci { |
||||||
|
status = "okay"; |
||||||
|
}; |
||||||
|
|
||||||
|
ðernet { |
||||||
|
mtd-mac-address = <&factory 0x28>; |
||||||
|
}; |
||||||
|
|
||||||
|
&wmac { |
||||||
|
ralink,mtd-eeprom = <&factory 0>; |
||||||
|
}; |
||||||
|
|
||||||
|
&pinctrl { |
||||||
|
state_default: pinctrl0 { |
||||||
|
default { |
||||||
|
ralink,group = "i2c", "uartf", "spi refclk", "ephy"; |
||||||
|
ralink,function = "gpio"; |
||||||
|
}; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
&pcie { |
||||||
|
status = "okay"; |
||||||
|
}; |
Loading…
Reference in new issue