Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. The U-Boot on WXR-2533DHP employs a complicated dual firmware protection scheme against corruptions of the kernel and rootfs images. See the notes in buffalo.sh for details. specifications: - Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T) - 512 MB of RAM (DDR3) - 256 MB of Flash (NAND) - 4T4R 2.4/5 GHz Wlan (QCA9980) - 5x 10/100/1000 Mbps Ethernet - 10x LEDs, 8x keys (6x buttons, 2x slide-switches) - 2x USB 3.0 Type-A - 12VDC/4A AC Adapter - UART through-hole on PCB - J3: Vcc, GND, TX, RX from USB port side - 115200n8 Boot instructions for the initramfs image: 1. Prepare the TFTP server with the initramfs image renamed to "wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10". 2. Press the "AOSS" button while powering on the WXR-2533DHP. 3. Wait until the "Wireless" LED flashes before releasing the AOSS button. The WXR-2533DHP will grab the image from TFTP server and will boot it. Flashing instructions: To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to let it finish the flashing process. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]master
parent
7e9b93fb1b
commit
51fe956c4f
@ -0,0 +1,45 @@ |
|||||||
|
#!/bin/sh |
||||||
|
# Copyright (C) 2018 OpenWrt.org |
||||||
|
# |
||||||
|
|
||||||
|
. /lib/functions.sh |
||||||
|
|
||||||
|
# The mtd partition 'ubi' and 'rootfs_1' on NAND flash are os-image |
||||||
|
# partitions. These partitions are called as "Bank1/Bank2" in U-Boot |
||||||
|
# on WXR-2533DHP, and they are checked conditions when booting. |
||||||
|
# Then, U-Boot checks kernel and rootfs volumes in ubi, but U-Boot |
||||||
|
# needs "ubi_rootfs" as rootfs volume name. And, U-Boot checks the |
||||||
|
# checksum at the end of rootfs (ubi_rootfs). |
||||||
|
# When U-Boot writes os-image into the Bank, only kernel, rootfs |
||||||
|
# (ubi_rootfs) and rootfs_data (ubi_rootfs_data) volumes are wrote |
||||||
|
# into the Bank. (not full ubi image) |
||||||
|
# |
||||||
|
# == U-Boot Behaviors == |
||||||
|
# - Bank1/Bank2 images are good, images are different |
||||||
|
# -> writes os-image to Bank1 from Bank2 |
||||||
|
# (this behavior is used to firmware upgrade in stock firmware) |
||||||
|
# - Bank1 image is broken (or checksum error) |
||||||
|
# -> writes os-image to Bank1 from Bank2 |
||||||
|
# - Bank2 image is broken (or checksum error) |
||||||
|
# -> writes os-image to Bank2 from Bank1 |
||||||
|
# - Bank1/Bank2 images are broken (or checksum error) |
||||||
|
# -> start tftp |
||||||
|
|
||||||
|
buffalo_upgrade_prepare_ubi() { |
||||||
|
local ubidev="$( nand_find_ubi ubi )" |
||||||
|
local mtdnum2="$( find_mtd_index rootfs_1 )" |
||||||
|
|
||||||
|
if [ ! "$mtdnum2" ]; then |
||||||
|
echo "cannot find second ubi mtd partition rootfs_1" |
||||||
|
return 1 |
||||||
|
fi |
||||||
|
|
||||||
|
local ubidev2="$( nand_find_ubi rootfs_1 )" |
||||||
|
if [ ! "$ubidev2" ] && [ -n "$mtdnum2" ]; then |
||||||
|
ubiattach -m "$mtdnum2" |
||||||
|
ubidev2="$( nand_find_ubi rootfs_1 )" |
||||||
|
fi |
||||||
|
|
||||||
|
ubirmvol /dev/$ubidev -N ubi_rootfs_data &> /dev/null || true |
||||||
|
ubirmvol /dev/$ubidev2 -N kernel &> /dev/null || true |
||||||
|
} |
@ -0,0 +1,535 @@ |
|||||||
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
||||||
|
#include "qcom-ipq8064-v2.0.dtsi" |
||||||
|
|
||||||
|
#include <dt-bindings/input/input.h> |
||||||
|
|
||||||
|
/ { |
||||||
|
model = "Buffalo WXR-2533DHP"; |
||||||
|
compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064"; |
||||||
|
|
||||||
|
memory@42000000 { |
||||||
|
reg = <0x42000000 0x1e000000>; |
||||||
|
device_type = "memory"; |
||||||
|
}; |
||||||
|
|
||||||
|
reserved-memory { |
||||||
|
#address-cells = <1>; |
||||||
|
#size-cells = <1>; |
||||||
|
ranges; |
||||||
|
rsvd@41200000 { |
||||||
|
reg = <0x41200000 0x300000>; |
||||||
|
no-map; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
aliases { |
||||||
|
serial0 = &gsbi4_serial; |
||||||
|
|
||||||
|
led-boot = &power; |
||||||
|
led-failsafe = &diag; |
||||||
|
led-running = &power; |
||||||
|
led-upgrade = &power; |
||||||
|
}; |
||||||
|
|
||||||
|
chosen { |
||||||
|
/* use "ubi_rootfs" volume in "ubi" partition as rootfs */ |
||||||
|
bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs"; |
||||||
|
stdout-path = "serial0:115200n8"; |
||||||
|
}; |
||||||
|
|
||||||
|
soc { |
||||||
|
nand@1ac00000 { |
||||||
|
status = "okay"; |
||||||
|
|
||||||
|
pinctrl-0 = <&nand_pins>; |
||||||
|
pinctrl-names = "default"; |
||||||
|
|
||||||
|
cs@0 { |
||||||
|
reg = <0>; |
||||||
|
compatible = "qcom,nandcs"; |
||||||
|
|
||||||
|
nand-ecc-strength = <4>; |
||||||
|
nand-bus-width = <8>; |
||||||
|
nand-ecc-step-size = <512>; |
||||||
|
|
||||||
|
partitions { |
||||||
|
compatible = "fixed-partitions"; |
||||||
|
#address-cells = <1>; |
||||||
|
#size-cells = <1>; |
||||||
|
|
||||||
|
ubi@0 { |
||||||
|
label = "ubi"; |
||||||
|
reg = <0x0000000 0x4000000>; |
||||||
|
}; |
||||||
|
|
||||||
|
rootfs_1@4000000 { |
||||||
|
label = "rootfs_1"; |
||||||
|
reg = <0x4000000 0x4000000>; |
||||||
|
}; |
||||||
|
}; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
mdio { |
||||||
|
compatible = "virtual,mdio-gpio"; |
||||||
|
#address-cells = <1>; |
||||||
|
#size-cells = <0>; |
||||||
|
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, |
||||||
|
<&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; |
||||||
|
pinctrl-0 = <&mdio0_pins>; |
||||||
|
pinctrl-names = "default"; |
||||||
|
|
||||||
|
ethernet-phy@0 { |
||||||
|
reg = <0>; |
||||||
|
qca,ar8327-initvals = < |
||||||
|
0x00004 0x07600000 /* PAD0_MODE */ |
||||||
|
0x00008 0x01000000 /* PAD5_MODE */ |
||||||
|
0x0000c 0x00000080 /* PAD6_MODE */ |
||||||
|
0x00050 0xcc35cc35 /* LED_CTRL0 */ |
||||||
|
0x00054 0xca35ca35 /* LED_CTRL1 */ |
||||||
|
0x00058 0xc935c935 /* LED_CTRL2 */ |
||||||
|
0x0005c 0x03ffff00 /* LED_CTRL3 */ |
||||||
|
0x000e4 0x0006a545 /* MAC_POWER_SEL */ |
||||||
|
0x000e0 0xc74164de /* SGMII_CTRL */ |
||||||
|
0x0007c 0x0000007e /* PORT0_STATUS */ |
||||||
|
0x00094 0x0000007e /* PORT6_STATUS */ |
||||||
|
>; |
||||||
|
}; |
||||||
|
|
||||||
|
ethernet-phy@4 { |
||||||
|
reg = <4>; |
||||||
|
}; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
leds { |
||||||
|
compatible = "gpio-leds"; |
||||||
|
pinctrl-0 = <&led_pins>; |
||||||
|
pinctrl-names = "default"; |
||||||
|
|
||||||
|
usb { |
||||||
|
label = "wxr-2533dhp:green:usb"; |
||||||
|
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; |
||||||
|
linux,default-trigger = "usbport"; |
||||||
|
trigger-sources = <&hub_port0 &hub_port1>; |
||||||
|
}; |
||||||
|
|
||||||
|
guestport { |
||||||
|
label = "wxr-2533dhp:green:guestport"; |
||||||
|
gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; |
||||||
|
}; |
||||||
|
|
||||||
|
diag: diag { |
||||||
|
label = "wxr-2533dhp:orange:diag"; |
||||||
|
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; |
||||||
|
}; |
||||||
|
|
||||||
|
internet_orange { |
||||||
|
label = "wxr-2533dhp:orange:internet"; |
||||||
|
gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; |
||||||
|
}; |
||||||
|
|
||||||
|
internet_white { |
||||||
|
label = "wxr-2533dhp:white:internet"; |
||||||
|
gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; |
||||||
|
}; |
||||||
|
|
||||||
|
wireless_orange { |
||||||
|
label = "wxr-2533dhp:orange:wireless"; |
||||||
|
gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; |
||||||
|
}; |
||||||
|
|
||||||
|
wireless_white { |
||||||
|
label = "wxr-2533dhp:white:wireless"; |
||||||
|
gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; |
||||||
|
}; |
||||||
|
|
||||||
|
router_orange { |
||||||
|
label = "wxr-2533dhp:orange:router"; |
||||||
|
gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>; |
||||||
|
}; |
||||||
|
|
||||||
|
router_white { |
||||||
|
label = "wxr-2533dhp:white:router"; |
||||||
|
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; |
||||||
|
}; |
||||||
|
|
||||||
|
power: power { |
||||||
|
label = "wxr-2533dhp:white:power"; |
||||||
|
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
keys { |
||||||
|
compatible = "gpio-keys"; |
||||||
|
pinctrl-0 = <&button_pins>; |
||||||
|
pinctrl-names = "default"; |
||||||
|
|
||||||
|
power { |
||||||
|
label = "power"; |
||||||
|
gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>; |
||||||
|
linux,code = <KEY_POWER>; |
||||||
|
}; |
||||||
|
|
||||||
|
reset { |
||||||
|
label = "reset"; |
||||||
|
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; |
||||||
|
linux,code = <KEY_RESTART>; |
||||||
|
}; |
||||||
|
|
||||||
|
wps { |
||||||
|
label = "wps"; |
||||||
|
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; |
||||||
|
linux,code = <KEY_WPS_BUTTON>; |
||||||
|
}; |
||||||
|
|
||||||
|
eject { |
||||||
|
label = "eject"; |
||||||
|
gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; |
||||||
|
linux,code = <KEY_EJECTCD>; |
||||||
|
}; |
||||||
|
|
||||||
|
guest { |
||||||
|
label = "guest"; |
||||||
|
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; |
||||||
|
linux,code = <BTN_0>; |
||||||
|
}; |
||||||
|
|
||||||
|
ap { |
||||||
|
label = "ap"; |
||||||
|
gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>; |
||||||
|
linux,code = <BTN_1>; |
||||||
|
linux,input-type = <EV_SW>; |
||||||
|
}; |
||||||
|
|
||||||
|
router { |
||||||
|
label = "router"; |
||||||
|
gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>; |
||||||
|
linux,code = <BTN_1>; |
||||||
|
linux,input-type = <EV_SW>; |
||||||
|
}; |
||||||
|
|
||||||
|
auto { |
||||||
|
label = "auto"; |
||||||
|
gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>; |
||||||
|
linux,code = <BTN_1>; |
||||||
|
linux,input-type = <EV_SW>; |
||||||
|
}; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
&adm_dma { |
||||||
|
status = "okay"; |
||||||
|
}; |
||||||
|
|
||||||
|
&gmac1 { |
||||||
|
status = "okay"; |
||||||
|
|
||||||
|
phy-mode = "rgmii"; |
||||||
|
qcom,id = <1>; |
||||||
|
|
||||||
|
pinctrl-0 = <&rgmii2_pins>; |
||||||
|
pinctrl-names = "default"; |
||||||
|
|
||||||
|
mtd-mac-address = <&ART 6>; |
||||||
|
|
||||||
|
fixed-link { |
||||||
|
speed = <1000>; |
||||||
|
full-duplex; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
&gmac2 { |
||||||
|
status = "ok"; |
||||||
|
|
||||||
|
phy-mode = "sgmii"; |
||||||
|
qcom,id = <2>; |
||||||
|
|
||||||
|
mtd-mac-address = <&ART 0>; |
||||||
|
|
||||||
|
fixed-link { |
||||||
|
speed = <1000>; |
||||||
|
full-duplex; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
&gsbi4 { |
||||||
|
status = "okay"; |
||||||
|
qcom,mode = <GSBI_PROT_I2C_UART>; |
||||||
|
}; |
||||||
|
|
||||||
|
&gsbi4_serial { |
||||||
|
status = "okay"; |
||||||
|
|
||||||
|
pinctrl-0 = <&uart0_pins>; |
||||||
|
pinctrl-names = "default"; |
||||||
|
}; |
||||||
|
|
||||||
|
&gsbi5 { |
||||||
|
status = "okay"; |
||||||
|
qcom,mode = <GSBI_PROT_SPI>; |
||||||
|
|
||||||
|
spi@1a280000 { |
||||||
|
status = "okay"; |
||||||
|
|
||||||
|
pinctrl-0 = <&spi_pins>; |
||||||
|
pinctrl-names = "default"; |
||||||
|
|
||||||
|
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; |
||||||
|
|
||||||
|
flash@0 { |
||||||
|
compatible = "jedec,spi-nor"; |
||||||
|
spi-max-frequency = <50000000>; |
||||||
|
reg = <0>; |
||||||
|
|
||||||
|
partitions { |
||||||
|
compatible = "fixed-partitions"; |
||||||
|
#address-cells = <1>; |
||||||
|
#size-cells = <1>; |
||||||
|
|
||||||
|
SBL1@0 { |
||||||
|
label = "SBL1"; |
||||||
|
reg = <0x0 0x10000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
MIBIB@10000 { |
||||||
|
label = "MIBIB"; |
||||||
|
reg = <0x10000 0x20000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
SBL2@30000 { |
||||||
|
label = "SBL2"; |
||||||
|
reg = <0x30000 0x30000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
SBL3@60000 { |
||||||
|
label = "SBL3"; |
||||||
|
reg = <0x60000 0x30000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
DDRCONFIG@90000 { |
||||||
|
label = "DDRCONFIG"; |
||||||
|
reg = <0x90000 0x10000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
SSD@a0000 { |
||||||
|
label = "SSD"; |
||||||
|
reg = <0xa0000 0x10000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
TZ@b0000 { |
||||||
|
label = "TZ"; |
||||||
|
reg = <0xb0000 0x30000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
RPM@e0000 { |
||||||
|
label = "RPM"; |
||||||
|
reg = <0xe0000 0x20000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
APPSBL@100000 { |
||||||
|
label = "APPSBL"; |
||||||
|
reg = <0x100000 0x70000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
APPSBLENV@170000 { |
||||||
|
label = "APPSBLENV"; |
||||||
|
reg = <0x170000 0x10000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
ART: ART@180000 { |
||||||
|
label = "ART"; |
||||||
|
reg = <0x180000 0x40000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
BOOTCONFIG@1c0000 { |
||||||
|
label = "BOOTCONFIG"; |
||||||
|
reg = <0x1c0000 0x10000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
|
||||||
|
APPSBL_1@1d0000 { |
||||||
|
label = "APPSBL_1"; |
||||||
|
reg = <0x1d0000 0x70000>; |
||||||
|
read-only; |
||||||
|
}; |
||||||
|
}; |
||||||
|
}; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
&hs_phy_0 { /* USB3 port 0 HS phy */ |
||||||
|
status = "okay"; |
||||||
|
}; |
||||||
|
|
||||||
|
&ss_phy_0 { /* USB3 port 0 SS phy */ |
||||||
|
status = "okay"; |
||||||
|
}; |
||||||
|
|
||||||
|
&hs_phy_1 { /* USB3 port 1 HS phy */ |
||||||
|
status = "okay"; |
||||||
|
}; |
||||||
|
|
||||||
|
&ss_phy_1 { /* USB3 port 1 SS phy */ |
||||||
|
status = "okay"; |
||||||
|
}; |
||||||
|
|
||||||
|
&usb3_0 { |
||||||
|
status = "okay"; |
||||||
|
|
||||||
|
pinctrl-0 = <&usb_pwr_en_pins>; |
||||||
|
pinctrl-names = "default"; |
||||||
|
}; |
||||||
|
|
||||||
|
&usb3_1 { |
||||||
|
status = "okay"; |
||||||
|
}; |
||||||
|
|
||||||
|
&dwc3_0 { |
||||||
|
#address-cells = <1>; |
||||||
|
#size-cells = <0>; |
||||||
|
|
||||||
|
hub_port0: port@1 { |
||||||
|
reg = <1>; |
||||||
|
#trigger-source-cells = <0>; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
&dwc3_1 { |
||||||
|
#address-cells = <1>; |
||||||
|
#size-cells = <0>; |
||||||
|
|
||||||
|
hub_port1: port@1 { |
||||||
|
reg = <1>; |
||||||
|
#trigger-source-cells = <0>; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
&pcie0 { |
||||||
|
status = "okay"; |
||||||
|
}; |
||||||
|
|
||||||
|
&pcie1 { |
||||||
|
status = "okay"; |
||||||
|
force_gen1 = <1>; |
||||||
|
}; |
||||||
|
|
||||||
|
&qcom_pinmux { |
||||||
|
button_pins: button_pins { |
||||||
|
mux { |
||||||
|
pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57", |
||||||
|
"gpio58", "gpio64", "gpio65"; |
||||||
|
function = "gpio"; |
||||||
|
drive-strength = <2>; |
||||||
|
bias-pull-up; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
led_pins: led_pins { |
||||||
|
mux { |
||||||
|
pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22", |
||||||
|
"gpio23", "gpio24", "gpio25", "gpio26", "gpio53"; |
||||||
|
function = "gpio"; |
||||||
|
drive-strength = <2>; |
||||||
|
bias-pull-up; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
uart0_pins: uart0_pins { |
||||||
|
mux { |
||||||
|
pins = "gpio10", "gpio11"; |
||||||
|
function = "gsbi4"; |
||||||
|
drive-strength = <12>; |
||||||
|
bias-disable; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
spi_pins: spi_pins { |
||||||
|
mux { |
||||||
|
pins = "gpio18", "gpio19", "gpio21"; |
||||||
|
function = "gsbi5"; |
||||||
|
bias-pull-down; |
||||||
|
}; |
||||||
|
|
||||||
|
data { |
||||||
|
pins = "gpio18", "gpio19"; |
||||||
|
drive-strength = <10>; |
||||||
|
}; |
||||||
|
|
||||||
|
cs{ |
||||||
|
pins = "gpio20"; |
||||||
|
drive-strength = <10>; |
||||||
|
bias-pull-up; |
||||||
|
}; |
||||||
|
|
||||||
|
clk { |
||||||
|
pins = "gpio21"; |
||||||
|
drive-strength = <12>; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
mdio0_pins: mdio0_pins { |
||||||
|
mux { |
||||||
|
pins = "gpio0", "gpio1"; |
||||||
|
function = "gpio"; |
||||||
|
drive-strength = <8>; |
||||||
|
bias-disable; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
nand_pins: nand_pins { |
||||||
|
mux { |
||||||
|
pins = "gpio34", "gpio35", "gpio36", |
||||||
|
"gpio37", "gpio38", "gpio39", |
||||||
|
"gpio40", "gpio41", "gpio42", |
||||||
|
"gpio43", "gpio44", "gpio45", |
||||||
|
"gpio46", "gpio47"; |
||||||
|
function = "nand"; |
||||||
|
drive-strength = <10>; |
||||||
|
bias-disable; |
||||||
|
}; |
||||||
|
|
||||||
|
pullups { |
||||||
|
pins = "gpio39"; |
||||||
|
bias-pull-up; |
||||||
|
}; |
||||||
|
|
||||||
|
hold { |
||||||
|
pins = "gpio40", "gpio41", "gpio42", |
||||||
|
"gpio43", "gpio44", "gpio45", |
||||||
|
"gpio46", "gpio47"; |
||||||
|
bias-bus-hold; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
rgmii2_pins: rgmii2_pins { |
||||||
|
mux { |
||||||
|
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", |
||||||
|
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; |
||||||
|
function = "rgmii2"; |
||||||
|
drive-strength = <8>; |
||||||
|
bias-disable; |
||||||
|
}; |
||||||
|
}; |
||||||
|
|
||||||
|
usb_pwr_en_pins: usb_pwr_en_pins { |
||||||
|
mux{ |
||||||
|
pins = "gpio68"; |
||||||
|
function = "gpio"; |
||||||
|
drive-strength = <2>; |
||||||
|
bias-pull-up; |
||||||
|
output-high; |
||||||
|
}; |
||||||
|
}; |
||||||
|
}; |
Loading…
Reference in new issue