* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
master
Sven Eckelmann
8 years ago
committed by
Mathias Kresin
parent
c6aac196b8
commit
0b20490207
@ -0,0 +1,240 @@ |
||||
/* Copyright (c) 2015, The Linux Foundation. All rights reserved. |
||||
* Copyright (c) 2017-2018, Sven Eckelmann <sven.eckelmann@openmesh.com> |
||||
* |
||||
* Permission to use, copy, modify, and/or distribute this software for any |
||||
* purpose with or without fee is hereby granted, provided that the above |
||||
* copyright notice and this permission notice appear in all copies. |
||||
* |
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
||||
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
||||
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR |
||||
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
||||
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN |
||||
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF |
||||
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
||||
* |
||||
*/ |
||||
|
||||
#include "qcom-ipq4019.dtsi" |
||||
#include "qcom-ipq4019-bus.dtsi" |
||||
#include <dt-bindings/gpio/gpio.h> |
||||
#include <dt-bindings/input/input.h> |
||||
#include <dt-bindings/soc/qcom,tcsr.h> |
||||
|
||||
/ { |
||||
model = "OpenMesh A62"; |
||||
compatible = "openmesh,a62", "qcom,ipq4019"; |
||||
|
||||
soc { |
||||
mdio@90000 { |
||||
status = "okay"; |
||||
}; |
||||
|
||||
ess-psgmii@98000 { |
||||
status = "okay"; |
||||
}; |
||||
|
||||
tcsr@194b000 { |
||||
/* select hostmode */ |
||||
compatible = "qcom,tcsr"; |
||||
reg = <0x194b000 0x100>; |
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; |
||||
status = "okay"; |
||||
}; |
||||
|
||||
tcsr@1949000 { |
||||
compatible = "qcom,tcsr"; |
||||
reg = <0x1949000 0x100>; |
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; |
||||
}; |
||||
|
||||
ess_tcsr@1953000 { |
||||
compatible = "qcom,tcsr"; |
||||
reg = <0x1953000 0x1000>; |
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>; |
||||
}; |
||||
|
||||
tcsr@1957000 { |
||||
compatible = "qcom,tcsr"; |
||||
reg = <0x1957000 0x100>; |
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; |
||||
}; |
||||
|
||||
usb2: usb2@60f8800 { |
||||
status = "okay"; |
||||
}; |
||||
|
||||
serial@78af000 { |
||||
pinctrl-0 = <&serial_pins>; |
||||
pinctrl-names = "default"; |
||||
status = "okay"; |
||||
}; |
||||
|
||||
crypto@8e3a000 { |
||||
status = "okay"; |
||||
}; |
||||
|
||||
watchdog@b017000 { |
||||
status = "okay"; |
||||
}; |
||||
|
||||
ess-switch@c000000 { |
||||
switch_lan_bmp = <0x10>; |
||||
switch_wan_bmp = <0x20>; |
||||
|
||||
status = "okay"; |
||||
}; |
||||
|
||||
edma@c080000 { |
||||
status = "okay"; |
||||
}; |
||||
}; |
||||
|
||||
gpio-keys { |
||||
compatible = "gpio-keys"; |
||||
|
||||
reset { |
||||
label = "reset"; |
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; |
||||
linux,code = <KEY_RESTART >; |
||||
}; |
||||
}; |
||||
|
||||
aliases { |
||||
led-boot = &power; |
||||
led-failsafe = &power; |
||||
led-running = &power; |
||||
led-upgrade = &power; |
||||
}; |
||||
|
||||
gpio-leds { |
||||
compatible = "gpio-leds"; |
||||
|
||||
red { |
||||
label = "a62:red:status"; |
||||
gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>; |
||||
linux,default-trigger = "default-off"; |
||||
}; |
||||
|
||||
power: green { |
||||
label = "a62:green:status"; |
||||
gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>; |
||||
}; |
||||
|
||||
blue { |
||||
label = "a62:blue:status"; |
||||
gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>; |
||||
linux,default-trigger = "default-off"; |
||||
}; |
||||
}; |
||||
|
||||
watchdog { |
||||
compatible = "linux,wdt-gpio"; |
||||
gpios = <&tlmm 59 GPIO_ACTIVE_LOW>; |
||||
hw_algo = "toggle"; |
||||
/* hw_margin_ms is actually 300s but driver limits it to 60s */ |
||||
hw_margin_ms = <60000>; |
||||
always-running; |
||||
}; |
||||
}; |
||||
|
||||
&tlmm { |
||||
serial_pins: serial_pinmux { |
||||
mux { |
||||
pins = "gpio16", "gpio17"; |
||||
function = "blsp_uart0"; |
||||
bias-disable; |
||||
}; |
||||
}; |
||||
|
||||
spi_0_pins: spi_0_pinmux { |
||||
pin { |
||||
function = "blsp_spi0"; |
||||
pins = "gpio13", "gpio14", "gpio15"; |
||||
drive-strength = <12>; |
||||
bias-disable; |
||||
}; |
||||
pin_cs { |
||||
function = "gpio"; |
||||
pins = "gpio12"; |
||||
drive-strength = <2>; |
||||
bias-disable; |
||||
output-high; |
||||
}; |
||||
}; |
||||
|
||||
enable-usb-power { |
||||
gpio-hog; |
||||
gpios = <58 GPIO_ACTIVE_HIGH>; |
||||
output-low; |
||||
line-name = "enable USB2 power"; |
||||
}; |
||||
}; |
||||
|
||||
&blsp_dma { |
||||
status = "okay"; |
||||
}; |
||||
|
||||
&spi_0 { |
||||
pinctrl-0 = <&spi_0_pins>; |
||||
pinctrl-names = "default"; |
||||
status = "okay"; |
||||
cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; |
||||
|
||||
m25p80@0 { |
||||
#address-cells = <1>; |
||||
#size-cells = <1>; |
||||
compatible = "jedec,spi-nor"; |
||||
reg = <0>; |
||||
spi-max-frequency = <24000000>; |
||||
/* partitions are passed via bootloader */ |
||||
}; |
||||
}; |
||||
|
||||
&cryptobam { |
||||
status = "okay"; |
||||
}; |
||||
|
||||
&gmac0 { |
||||
qcom,phy_mdio_addr = <3>; |
||||
qcom,poll_required = <1>; |
||||
qcom,forced_speed = <1000>; |
||||
qcom,forced_duplex = <1>; |
||||
vlan_tag = <1 0x10>; |
||||
}; |
||||
|
||||
&usb2_hs_phy { |
||||
status = "okay"; |
||||
}; |
||||
|
||||
&pcie0 { |
||||
status = "okay"; |
||||
perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; |
||||
wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; |
||||
|
||||
pcie@0 { |
||||
reg = <0 0 0 0 0>; |
||||
#interrupt-cells = <1>; |
||||
#size-cells = <2>; |
||||
#address-cells = <3>; |
||||
device_type = "pci"; |
||||
|
||||
ath10k@0,0 { |
||||
compatible = "qcom,ath10k"; |
||||
status = "okay"; |
||||
reg = <0 0 0 0 0>; |
||||
device_type = "pci"; |
||||
qcom,ath10k-calibration-variant = "OM-A62"; |
||||
}; |
||||
}; |
||||
}; |
||||
|
||||
&wifi0 { |
||||
status = "okay"; |
||||
qcom,ath10k-calibration-variant = "OM-A62"; |
||||
}; |
||||
|
||||
&wifi1 { |
||||
status = "okay"; |
||||
qcom,ath10k-calibration-variant = "OM-A62"; |
||||
}; |
||||
Loading…
Reference in new issue