connect disks pre-emptively upon startup, to ensure we have
enough disks are connected at startup rather than wait
for them.
we need to do this to avoid long wait times for server to
be online when we have servers come up in rolling upgrade
fashion
Only use dynamic delays for the crawler. Even though the max wait was 1 second the number
of waits could severely impact crawler speed.
Instead of relying on a global metric, we use the stateless local delays to keep the crawler
running at a speed more adjusted to current conditions.
The only case we keep it is before bitrot checks when enabled.
This PR fixes a hang which occurs quite commonly at higher concurrency
by allowing following changes
- allowing lower connections in time_wait allows faster socket open's
- lower idle connection timeout to ensure that we let kernel
reclaim the time_wait connections quickly
- increase somaxconn to 4096 instead of 2048 to allow larger tcp
syn backlogs.
fixes#10413
This change tracks bandwidth for a bucket and object
- [x] Add Admin API
- [x] Add Peer API
- [x] Add BW throttling
- [x] Admin APIs to set replication limit
- [x] Admin APIs for fetch bandwidth
In almost all scenarios MinIO now is
mostly ready for all sub-systems
independently, safe-mode is not useful
anymore and do not serve its original
intended purpose.
allow server to be fully functional
even with config partially configured,
this is to cater for availability of actual
I/O v/s manually fixing the server.
In k8s like environments it will never make
sense to take pod into safe-mode state,
because there is no real access to perform
any remote operation on them.
- select lockers which are non-local and online to have
affinity towards remote servers for lock contention
- optimize lock retry interval to avoid sending too many
messages during lock contention, reduces average CPU
usage as well
- if bucket is not set, when deleteObject fails make sure
setPutObjHeaders() honors lifecycle only if bucket name
is set.
- fix top locks to list out always the oldest lockers always,
avoid getting bogged down into map's unordered nature.
This is to allow remote targets to be generalized
for replication/ILM transition
Also adding a field in BucketTarget to identify
a remote target with a label.
This commit fixes a misuse of the `http.ResponseWriter.WriteHeader`.
A caller should **either** call `WriteHeader` exactly once **or**
write to the response writer and causing an implicit 200 OK.
Writing the response headers more than once causes a `http: superfluous
response.WriteHeader call` log message. This commit fixes this
by preventing a 2nd `WriteHeader` call being forwarded to the underlying
`ResponseWriter`.
Updates #10587
* add NVMe drive info [model num, serial num, drive temp. etc.]
* Ignore fuse partitions
* Add the nvme logic only for linux
* Move smart/nvme structs to a separate file
Co-authored-by: wlan0 <sidharthamn@gmail.com>
throw proper error when port is not accessible
for the regular user, this is possibly a regression.
```
ERROR Unable to start the server: Insufficient permissions to use specified port
> Please ensure MinIO binary has 'cap_net_bind_service=+ep' permissions
HINT:
Use 'sudo setcap cap_net_bind_service=+ep /path/to/minio' to provide sufficient permissions
```
After #10594 let's invalidate the bloom filters to force the next cycles to go through all data.
There is a small chance that the linked PR could have caused missing bloom filter data.
This will invalidate the current bloom filters and make the crawler go through everything.
Routing using on source IP if found. This should distribute
the listing load for V1 and versioning on multiple nodes
evenly between different clients.
If source IP is not found from the http request header, then falls back
to bucket name instead.
Disallow versioning suspension on a bucket with
pre-existing replication configuration
If versioning is suspended on the target,replication
should fail.
`mc admin info` on busy setups will not move HDD
heads unnecessarily for repeated calls, provides
a better responsiveness for the call overall.
Bonus change allow listTolerancePerSet be N-1
for good entries, to avoid skipping entries
for some reason one of the disk went offline.
add a hint on the disk to allow for tracking fresh disk
being healed, to allow for restartable heals, and also
use this as a way to track and remove disks.
There are more pending changes where we should move
all the disk formatting logic to backend drives, this
PR doesn't deal with this refactor instead makes it
easier to track healing in the future.
- Add owner information for expiry, locking, unlocking a resource
- TopLocks returns now locks in quorum by default, provides
a way to capture stale locks as well with `?stale=true`
- Simplify the quorum handling for locks to avoid from storage
class, because there were challenges to make it consistent
across all situations.
- And other tiny simplifications to reset locks.
context canceled errors bubbling up from the network
layer has the potential to be misconstrued as network
errors, taking prematurely a server offline and triggering
a health check routine avoid this potential occurrence.
isEnded() was incorrectly calculating if the current healing sequence is
ended or not. h.currentStatus.Items could be empty if healing is very
slow and mc admin heal consumed all items.
As the bulk/recursive delete will require multiple connections to open at an instance,
The default open connections limit will be reached which results in the following error
```FATAL: sorry, too many clients already```
By setting the open connections to a reasonable value - `2`, We ensure that the max open connections
will not be exhausted and lie under bounds.
The queries are simple inserts/updates/deletes which is operational and sufficient with the
the maximum open connection limit is 2.
Fixes#10553
Allow user configuration for MaxOpenConnections
It is possible the heal drives are not reported from
the maintenance check because the background heal
state simply relied on the `format.json` for capturing
unformatted drives. It is possible that drives might
be still healing - make sure that applications which
rely on cluster health check respond back this detail.
Also, revamp the way ListBuckets work make few portions
of the healing logic parallel
- walk objects for healing disks in parallel
- collect the list of buckets in parallel across drives
- provide consistent view for listBuckets()
Harshavardhana