Also, revamp the way ListBuckets work make few portions
of the healing logic parallel
- walk objects for healing disks in parallel
- collect the list of buckets in parallel across drives
- provide consistent view for listBuckets()
It was observed in VMware vsphere environment during a
pod replacement, `mc admin info` might report incorrect
offline nodes for the replaced drive. This issue eventually
goes away but requires quite a lot of time for all servers
to be in sync.
This PR fixes this behavior properly.
This is to ensure that Go contexts work properly, after some
interesting experiments I found that Go net/http doesn't
cancel the context when Body is non-zero and hasn't been
read till EOF.
The following gist explains this, this can lead to pile up
of go-routines on the server which will never be canceled
and will die at a really later point in time, which can
simply overwhelm the server.
https://gist.github.com/harshavardhana/c51dcfd055780eaeb71db54f9c589150
To avoid this refactor the locking such that we take locks after we
have started reading from the body and only take locks when needed.
Also, remove contextReader as it's not useful, doesn't work as expected
context is not canceled until the body reaches EOF so there is no point
in wrapping it with context and putting a `select {` on it which
can unnecessarily increase the CPU overhead.
We will still use the context to cancel the lockers etc.
Additional simplification in the locker code to avoid timers
as re-using them is a complicated ordeal avoid them in
the hot path, since locking is very common this may avoid
lots of allocations.
inconsistent drive healing when one of the drive is offline
while a new drive was replaced, this change is to ensure
that we can add the offline drive back into the mix by
healing it again.
- do not fail the healthcheck if heal status
was not obtained from one of the nodes,
if many nodes fail then report this as a
catastrophic error.
- add "x-minio-write-quorum" value to match
the write tolerance supported by server.
- admin info now states if a drive is healing
where madmin.Disk.Healing is set to true
and madmin.Disk.State is "ok"
We can reduce this further in the future, but this is a good
value to keep around. With the advent of continuous healing,
we can be assured that namespace will eventually be
consistent so we are okay to avoid the necessity to
a list across all drives on all sets.
Bonus Pop()'s in parallel seem to have the potential to
wait too on large drive setups and cause more slowness
instead of gaining any performance remove it for now.
Also, implement load balanced reply for local disks,
ensuring that local disks have an affinity for
- cleanupStaleMultipartUploads()
We should only enforce quotas if no error has been returned.
firstErr is safe to access since all goroutines have exited at this point.
If `firstErr` hasn't been set by something else return the context error if cancelled.
Keep dataUpdateTracker while goroutine is starting.
This will ensure the object is updated one `start` returns
Tested with
```
λ go test -cpu=1,2,4,8 -test.run TestDataUpdateTracker -count=1000
PASS
ok github.com/minio/minio/cmd 8.913s
```
Fixes#10295
newDynamicTimeout should be allocated once, in-case
of temporary locks in config and IAM we should
have allocated timeout once before the `for loop`
This PR doesn't fix any issue as such, but provides
enough dynamism for the timeout as per expectation.
use `/etc/hosts` instead of `/` to check for common
device id, if the device is same for `/etc/hosts`
and the --bind mount to detect root disks.
Bonus enhance healthcheck logging by adding maintenance
tags, for all messages.
It is possible in situations when server was deployed
in asymmetric configuration in the past such as
```
minio server ~/fs{1...4}/disk{1...5}
```
Results in setDriveCount of 10 in older releases
but with fairly recent releases we have moved to
having server affinity which means that a set drive
count ascertained from above config will be now '4'
While the object layer make sure that we honor
`format.json` the storageClass configuration however
was by mistake was using the global value obtained
by heuristics. Which leads to prematurely using
lower parity without being requested by the an
administrator.
This PR fixes this behavior.
when source and destination are same and versioning is enabled
on the destination bucket - we do not need to re-create the entire
object once again to optimize on space utilization.
Cases this PR is not supporting
- any pre-existing legacy object will not
be preserved in this manner, meaning a new
dataDir will be created.
- key-rotation and storage class changes
of course will never re-use the dataDir
this is to detect situations of corruption disk
format etc errors quickly and keep the disk online
in such scenarios for requests to fail appropriately.
This PR adds support for healing older
content i.e from 2yrs, 1yr. Also handles
other situations where our config was
not encrypted yet.
This PR also ensures that our Listing
is consistent and quorum friendly,
such that we don't list partial objects
Enforce bucket quotas when crawling has finished.
This ensures that we will not do quota enforcement on old data.
Additionally, delete less if we are closer to quota than we thought.
- admin info node offline check is now quicker
- admin info now doesn't duplicate the code
across doing the same checks for disks
- rely on StorageInfo to return appropriate errors
instead of calling locally.
- diskID checks now return proper errors when
disk not found v/s format.json missing.
- add more disk states for more clarity on the
underlying disk errors.
The S3 specification says that versions are ordered in the response of
list object versions.
mc snapshot needs this to know which version comes first especially when
two versions have the same exact last-modified field.
Bonus fix during versioning merge one of the PR was missing
the offline/online disk count fix from #9801 port it correctly
over to the master branch from release.
Additionally, add versionID support for MRF
Fixes#9910Fixes#9931
Looking into full disk errors on zoned setup. We don't take the
5% space requirement into account when selecting a zone.
The interesting part is that even considering this we don't
know the size of the object the user wants to upload when
they do multipart uploads.
It seems quite defensive to always upload multiparts to
the zone where there is the most space since all load will
be directed to a part of the cluster.
In these cases we make sure it can at least hold a 1GiB file
and we disadvantage fuller zones more by subtracting the
expected size before weighing.
Just like GET/DELETE APIs it is possible to preserve
client supplied versionId's, of course the versionIds
have to be uuid, if an existing versionId is found
it is overwritten if no object locking policies
are found.
- PUT /bucketname/objectname?versionId=<id>
- POST /bucketname/objectname?uploads=&versionId=<id>
- PUT /bucketname/objectname?verisonId=<id> (with x-amz-copy-source)
PutObject on multiple-zone with versioning would not
overwrite the correct location of the object if the
object has delete marker, leading to duplicate objects
on two zones.
This PR fixes by adding affinity towards delete marker
when GetObjectInfo() returns error, use the zone index
which has the delete marker.
- Implement a new xl.json 2.0.0 format to support,
this moves the entire marshaling logic to POSIX
layer, top layer always consumes a common FileInfo
construct which simplifies the metadata reads.
- Implement list object versions
- Migrate to siphash from crchash for new deployments
for object placements.
Fixes#2111
CopyObject was not correctly figuring out the correct
destination object location and would end up creating
duplicate objects on two different zones, reproduced
by doing encryption based key rotation.
Harshavardhana