You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
freifunkist-firmware/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts

535 lines
9.1 KiB

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qcom-ipq8064-v2.0.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "Buffalo WXR-2533DHP";
compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064";
memory@42000000 {
reg = <0x42000000 0x1e000000>;
device_type = "memory";
};
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
rsvd@41200000 {
reg = <0x41200000 0x300000>;
no-map;
};
};
aliases {
serial0 = &gsbi4_serial;
led-boot = &power;
led-failsafe = &diag;
led-running = &power;
led-upgrade = &power;
};
chosen {
/* use "ubi_rootfs" volume in "ubi" partition as rootfs */
bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs";
stdout-path = "serial0:115200n8";
};
soc {
nand@1ac00000 {
status = "okay";
pinctrl-0 = <&nand_pins>;
pinctrl-names = "default";
cs@0 {
reg = <0>;
compatible = "qcom,nandcs";
nand-ecc-strength = <4>;
nand-bus-width = <8>;
nand-ecc-step-size = <512>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
ubi@0 {
label = "ubi";
reg = <0x0000000 0x4000000>;
};
rootfs_1@4000000 {
label = "rootfs_1";
reg = <0x4000000 0x4000000>;
};
};
};
};
mdio {
compatible = "virtual,mdio-gpio";
#address-cells = <1>;
#size-cells = <0>;
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
<&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&mdio0_pins>;
pinctrl-names = "default";
ethernet-phy@0 {
reg = <0>;
qca,ar8327-initvals = <
0x00004 0x07600000 /* PAD0_MODE */
0x00008 0x01000000 /* PAD5_MODE */
0x0000c 0x00000080 /* PAD6_MODE */
0x00050 0xcc35cc35 /* LED_CTRL0 */
0x00054 0xca35ca35 /* LED_CTRL1 */
0x00058 0xc935c935 /* LED_CTRL2 */
0x0005c 0x03ffff00 /* LED_CTRL3 */
0x000e4 0x0006a545 /* MAC_POWER_SEL */
0x000e0 0xc74164de /* SGMII_CTRL */
0x0007c 0x0000007e /* PORT0_STATUS */
0x00094 0x0000007e /* PORT6_STATUS */
>;
};
ethernet-phy@4 {
reg = <4>;
};
};
};
leds {
compatible = "gpio-leds";
pinctrl-0 = <&led_pins>;
pinctrl-names = "default";
usb {
label = "wxr-2533dhp:green:usb";
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "usbport";
trigger-sources = <&hub_port0 &hub_port1>;
};
guestport {
label = "wxr-2533dhp:green:guestport";
gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
};
diag: diag {
label = "wxr-2533dhp:orange:diag";
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
};
internet_orange {
label = "wxr-2533dhp:orange:internet";
gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
};
internet_white {
label = "wxr-2533dhp:white:internet";
gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
};
wireless_orange {
label = "wxr-2533dhp:orange:wireless";
gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
};
wireless_white {
label = "wxr-2533dhp:white:wireless";
gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
};
router_orange {
label = "wxr-2533dhp:orange:router";
gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
};
router_white {
label = "wxr-2533dhp:white:router";
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
};
power: power {
label = "wxr-2533dhp:white:power";
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
};
};
keys {
compatible = "gpio-keys";
pinctrl-0 = <&button_pins>;
pinctrl-names = "default";
power {
label = "power";
gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
};
reset {
label = "reset";
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
eject {
label = "eject";
gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
linux,code = <KEY_EJECTCD>;
};
guest {
label = "guest";
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
};
ap {
label = "ap";
gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>;
linux,code = <BTN_1>;
linux,input-type = <EV_SW>;
};
router {
label = "router";
gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
linux,code = <BTN_1>;
linux,input-type = <EV_SW>;
};
auto {
label = "auto";
gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>;
linux,code = <BTN_1>;
linux,input-type = <EV_SW>;
};
};
};
&adm_dma {
status = "okay";
};
&gmac1 {
status = "okay";
phy-mode = "rgmii";
qcom,id = <1>;
pinctrl-0 = <&rgmii2_pins>;
pinctrl-names = "default";
mtd-mac-address = <&ART 6>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
&gmac2 {
status = "ok";
phy-mode = "sgmii";
qcom,id = <2>;
mtd-mac-address = <&ART 0>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
&gsbi4 {
status = "okay";
qcom,mode = <GSBI_PROT_I2C_UART>;
};
&gsbi4_serial {
status = "okay";
pinctrl-0 = <&uart0_pins>;
pinctrl-names = "default";
};
&gsbi5 {
status = "okay";
qcom,mode = <GSBI_PROT_SPI>;
spi@1a280000 {
status = "okay";
pinctrl-0 = <&spi_pins>;
pinctrl-names = "default";
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
flash@0 {
compatible = "jedec,spi-nor";
spi-max-frequency = <50000000>;
reg = <0>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
SBL1@0 {
label = "SBL1";
reg = <0x0 0x10000>;
read-only;
};
MIBIB@10000 {
label = "MIBIB";
reg = <0x10000 0x20000>;
read-only;
};
SBL2@30000 {
label = "SBL2";
reg = <0x30000 0x30000>;
read-only;
};
SBL3@60000 {
label = "SBL3";
reg = <0x60000 0x30000>;
read-only;
};
DDRCONFIG@90000 {
label = "DDRCONFIG";
reg = <0x90000 0x10000>;
read-only;
};
SSD@a0000 {
label = "SSD";
reg = <0xa0000 0x10000>;
read-only;
};
TZ@b0000 {
label = "TZ";
reg = <0xb0000 0x30000>;
read-only;
};
RPM@e0000 {
label = "RPM";
reg = <0xe0000 0x20000>;
read-only;
};
APPSBL@100000 {
label = "APPSBL";
reg = <0x100000 0x70000>;
read-only;
};
APPSBLENV@170000 {
label = "APPSBLENV";
reg = <0x170000 0x10000>;
read-only;
};
ART: ART@180000 {
label = "ART";
reg = <0x180000 0x40000>;
read-only;
};
BOOTCONFIG@1c0000 {
label = "BOOTCONFIG";
reg = <0x1c0000 0x10000>;
read-only;
};
APPSBL_1@1d0000 {
label = "APPSBL_1";
reg = <0x1d0000 0x70000>;
read-only;
};
};
};
};
};
&hs_phy_0 { /* USB3 port 0 HS phy */
status = "okay";
};
&ss_phy_0 { /* USB3 port 0 SS phy */
status = "okay";
};
&hs_phy_1 { /* USB3 port 1 HS phy */
status = "okay";
};
&ss_phy_1 { /* USB3 port 1 SS phy */
status = "okay";
};
&usb3_0 {
status = "okay";
pinctrl-0 = <&usb_pwr_en_pins>;
pinctrl-names = "default";
};
&usb3_1 {
status = "okay";
};
&dwc3_0 {
#address-cells = <1>;
#size-cells = <0>;
hub_port0: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
&dwc3_1 {
#address-cells = <1>;
#size-cells = <0>;
hub_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
&pcie0 {
status = "okay";
};
&pcie1 {
status = "okay";
force_gen1 = <1>;
};
&qcom_pinmux {
button_pins: button_pins {
mux {
pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57",
"gpio58", "gpio64", "gpio65";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};
led_pins: led_pins {
mux {
pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22",
"gpio23", "gpio24", "gpio25", "gpio26", "gpio53";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};
uart0_pins: uart0_pins {
mux {
pins = "gpio10", "gpio11";
function = "gsbi4";
drive-strength = <12>;
bias-disable;
};
};
spi_pins: spi_pins {
mux {
pins = "gpio18", "gpio19", "gpio21";
function = "gsbi5";
bias-pull-down;
};
data {
pins = "gpio18", "gpio19";
drive-strength = <10>;
};
cs{
pins = "gpio20";
drive-strength = <10>;
bias-pull-up;
};
clk {
pins = "gpio21";
drive-strength = <12>;
};
};
mdio0_pins: mdio0_pins {
mux {
pins = "gpio0", "gpio1";
function = "gpio";
drive-strength = <8>;
bias-disable;
};
};
nand_pins: nand_pins {
mux {
pins = "gpio34", "gpio35", "gpio36",
"gpio37", "gpio38", "gpio39",
"gpio40", "gpio41", "gpio42",
"gpio43", "gpio44", "gpio45",
"gpio46", "gpio47";
function = "nand";
drive-strength = <10>;
bias-disable;
};
pullups {
pins = "gpio39";
bias-pull-up;
};
hold {
pins = "gpio40", "gpio41", "gpio42",
"gpio43", "gpio44", "gpio45",
"gpio46", "gpio47";
bias-bus-hold;
};
};
rgmii2_pins: rgmii2_pins {
mux {
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
function = "rgmii2";
drive-strength = <8>;
bias-disable;
};
};
usb_pwr_en_pins: usb_pwr_en_pins {
mux{
pins = "gpio68";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
output-high;
};
};
};