This now makes sure that the beginning of the version number gets checked
and "4.4.5" will not match was a supported version.
GCC 8 and GCC 9 are now marked as supported, but we probably have to fix
some problems for them.
Closes: FS#1433
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add initial support for Marvell MACCHIATObin, cortex-a72 based Marvell
ARMADA 8040 Community board. Comes in two forms: Single Shot and Double
Shot.
Specifications:
- Quad core Cortex-A72 (up to 2GHz)
- DDR4 DIMM slot with optional ECC and single/dual chip select support
- Dual 10GbE (1/2.5/10GbE) via copper or SFP
2.5GbE (1/2.5GbE) via SFP
1GbE via copper
- SPI Flash
- 3 X SATA 3.0 connectors
- MicroSD connector
- eMMC
- PCI x4 3.0 slot
- USB 2.0 Headers (Internal)
- USB 3.0 connector
- Console port (UART) over microUSB connector
- 20-pin Connector for CPU JTAG debugger
- 2 X UART Headers
- 12V input via DC Jack
- ATX type power connector
- Form Factor: Mini-ITX (170 mm x 170 mm)
More details at http://macchiatobin.net
Booting from micro SD card:
1. reset U-Boot environment:
env default -a
saveenv
2. prepare U-Boot with boot script:
setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
or manually:
setenv fdt_name armada-8040-mcbin.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr'
saveenv
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
Netfilter flow offload has now started to become useful and suitable for
a wider testing audience. Configuring it via UCI is also integrated in
firewall3 by adding 'option flow_offloading 1' to the 'defaults'
section in /etc/config/firewall
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Right patch version this time, sorry!
* Patch 180-usb-xhci-add-support-for-performing-fake-doorbell.patch had to be adjusted slightly because of upstream adapted code.
* Refreshed patches.
Compile-tested: ramips/mt7621, x86/64
Run-tested: ramips/mt7621, x86/64
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
Some devices only boot when a special config is found in the image and
completely ignore the default entry during the selection. These devices can
now use the variable DEVICE_DTS_CONFIG in their device image definition.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This reverts commit 43be5087a9.
The change is incompatible with the image builder code.
Luckily the RT-AC58U is no longer depending on the initramfs
being available for the target's image generation rules.
Reported-by: Venitex Aveon <aveon@aenote.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The image production rules does not have the initramfs-image
as a dependency. So, from make’s perspective initramfs
creation can run independently/in parallel with the image
generation code in the target's Makefile.
This is a problem for devices that have to use the initramfs
for the image creation and can lead to broken images.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Copying ./src/* would fail when src exists, but is empty or only contains
hidden files.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In addition to removing redundant code, this fixes various issues in
IB-generated images that have been fixed in prepare_rootfs before,
including better handling of CONFIG_CLEAN_IPKG and enabling of initscripts
from FILES.
We also reuse the opkg macro and remove --force-... flags that have been
removed from rootfs.mk as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
/usr/lib/opkg/status must not be removed completely, otherwise the
packages' conffile lists will be missing. Replace it with a reduced version
only containing the conffile entries.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
When a user removes a preinstalled opkg package, the package's prerm script
(and in particular our default_prerm) should run.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This bumps the 4.4. kernel in master to 4.4.119.
Includes more Meltdown & Spectre mitigation.
* Refresh patches.
* Refresh x86/config for RETPOLINE.
* Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream)
* Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream)
* Deleted 650-pppoe_header_pad.patch (does not apply anymore (code was replaced)).
Bumps from 4.4.112 to 4.4.115 were handled by Kevin Darbyshire-Bryant.
Compile-tested on: ar71xx & oxnas.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
This patch bumps the 4.14 kernel to .23.
- Refreshed patches.
- Deleted bcm53xx/patches-4.14/089-PCI-iproc-Fix-NULL-pointer-dereference-for-BCMA.patch. Has been accepted upstream.
- Deleted generic/pending-4.14/821-usb-Remove-annoying-warning-about-bogus-URB.patch. The upstream URB code was changed,
the patch no longer applies. I discussed this with the patch author and removed it for now, we'll see how it goes.
Compile-tested on: ramips/mt7621, x86/64
Run-tested on: ramips/mt7621, x86/64
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
This makes it possible to add an iptables rule that offloads routing/NAT
packet processing to a software fast path. This fast path is much
quicker than running packets through the regular tables/chains.
Requires Linux 4.14
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When using pigz, a parallel gzip implementation, the gzip step in the
image build for some targets fails, because the image filename already
has the .gz extension. This results in an emtpy image file. Fix this by
adding the --force option to gzip in the Build/gzip macro.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Martin Schleier <drahemmaps@gmx.net>
The current image build code has a number of race conditions and interface
contract violations in the custom image build steps:
- Build/install-zImage, solely used by at91, relies on $(PROFILE_SANITIZED)
which is not available when building with CONFIG_TARGET_MULTI_PROFILE
- Build/at91-sdcard, which may run concurrently, creates scratch files at
fixed locations and manipulates target files directly which can lead
to file corruption and other unexpected failures
Rename the install-zImage macro to at91-install-zImage and move it to the
at91 image Makefile since this target is the sole user. Also utilize "$@"
as output file name and switch the usage of $(PROFILE_SANITIZED) to
$(DEVICE_NAME) in order to fix naming under multi profile builds.
Fix the at91-sdcard macro to construct scratch file paths relative to "$@",
which is guaranteed to be unique and store the final artifact output in "$@"
as well, instead of inside $(BIN_DIR). The generic image build code takes
care of moving a build steps "$@" output to the final destination in a
concurrency-safe manner.
Finally remove the broken install-zImage from the generic image-commands
Makefile.
Fixes: d7a679a036 ("at91: Install zImage.")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In a profile, specifying -pkg in the list of PACKAGES will suppress
it even if it appears in the target's DEFAULT_PACKAGES list.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
It is currently possible to enable connlabel-support in iptables.
However, in order for connlabel to work properly, the kernel module must
also be present. This patch adds support for building the
connlabel-module, and selects it by default when connlabel-support is
enabled.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
This will make sure that the build system's
paths for linking are available.
This is needed mostly for linking with tools/libressl.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This would should up as `$$(HOSTCPPFLAGS)` in the host CFLAGS.
```
make --jobserver-fds=3,4 -j -C <openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/u-boot-A10-OLinuXino-Lime/u-boot-2017.07 CROSS_COMPILE=arm-openwrt-linux-muslgnueabi- DTC="<openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/linux-sunxi_cortexa8/linux-4.9.76/scripts/dtc/dtc" HOSTCC="gcc" HOSTCFLAGS='-O2 -I<openwrt>/staging_dir/host/include -I<openwrt>/staging_dir/host/usr/include -I<openwrt>/staging_dir/hostpkg/include -I<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/host/include $$(HOSTCPPFLAGS)' HOSTLDFLAGS="" BL31=<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/image/bl31.bin
```
And then it would complain with:
```
/bin/sh: 1: HOSTCPPFLAGS: not found
```
Also, HOSTCPPFLAGS does not exist.
The correct var is HOST_CPPFLAGS.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
We don't need two versions of this. The escaping quotes
is so that the sed commands aren't misinterpreted by shell;
it has nothing to do with the contents of the file, thus
one version is adequate.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
In addition to backslash and ampersand needing to be escaped for
simple sed RHS strings, we also need to escape comma since we're
using that as our s/// delimiter.
Pass everything through a macro filter to sanitize it.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
The nf_reject_ipv4 and nf_reject_ipv6 modules are moved into separate
packages, as they are a common dependency of ip(6)tables and nftables. This
avoids a dependency of nftables on kmod-nf-ipt(6). Also, fewer iptables
modules depend on nf-conntrack(6) now.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This fixes the following errors when doing "make package/install"
/home/yousong/git-repo/lede-project/lede/build_dir/target-mips_24kc_musl/root-malta/lib/functions/procd.sh: line 47: /home/yousong/git-repo/l
ede-project/lede/build_dir/target-mips_24kc_musl/root-malta/var/lock/procd_urandom_seed.lock: No such file or directory
flock: 1000: Bad file descriptor
Fixes FS#1260
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Configure variable SSP_SUPPORT is ambiguous for packages (tor, openssh,
avahi, freeswitch). It means 'toolchain supporting SSP', but for toolchain
and depends it means 'build gcc with libssp'.
Musl no longer uses libssp (1877bc9d8f), it has internal support, so
SSP_SUPPORT was disabled leading some package to not use SSP.
No information why Glibc and uClibc use libssp, but they may also provide
their own SSP support. uClibc used it own with commit 933b588e25 but it was
reverted in f3cacb9e84 without details.
Create an new configure GCC_LIBSSP and automatically enable SSP_SUPPORT
if either USE_MUSL or GCC_LIBSSP.
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
Introduce a configuration option to build a "hardened" OpenWrt with
ASLR PIE support.
Add new option PKG_ASLR_PIE to enable Address Space Layout Randomization (ASLR)
by building Position Independent Executables (PIE). This new option protects
against "return-to-text" attacks.
Busybox need a special care, link is done with ld, not gcc, leading to
unknown flags. Set BUSYBOX_DEFAULT_PIE instead and disable PKG_ASLR_PIE.
If other failing packages were found, PKG_ASLR_PIE:=0 should be added to
their Makefiles.
Original Work by: Yongkui Han <yonhan@cisco.com>
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
In case there is an external git repo specified,
it could overwrite the kernel tarball that was
downloaded from kernel.org.
The only identifier for such a file is the
KERNEL_GIT_CLONE_URI & KERNEL_GIT_REF symbols,
so if we have to download it we'll use that
information [after some sanitization]
to create a different filename for the kernel tarball.
If KERNEL_GIT_REF symbol is empty, HEAD will be used
as mentioned in the description of KERNEL_GIT_REF.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The Download/git rule will do a `git checkout <git-ref>`.
So, we can use any ref we want.
No need to limit just to branches.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
In commit fce35bce0f ("config: support new symbol intro'd in kernel
4.12")
I forgot to remove the initial debug test line.
This clearly is wrong as the same symbol is defined conditionally in the
line below as it should be.
I looked over it as I just checked if the symbol was present now upon
testing it.
Fixes: fce35bce0f ("config: support new symbol intro'd in kernel
4.12")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Eventually the BUILDONLY package flag could be replaced by simply creating
a package Makefile without any BuildPackage calls. This will fail for now,
as BuildPackage also causes the Makefile's compile target etc. to do
something useful at all.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Hauke Mehrtens