>From the Documentation/devicetree/bindings/leds/common.txt:
- default-state : The initial state of the LED. Valid values are "on", "off",
and "keep". If the LED is already on or off and the default-state property is
set the to same value, then no glitch should be produced where the LED
momentarily turns off (or on). The "keep" setting will keep the LED at
whatever its current state is, without producing a glitch. The default is
off if this property is not present.
So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Netgear R6350 is a wireless router, aka Netgear AC1750.
Specification:
- SoC: Mediatek MT7621AT (2 CPU cores, 4 threads)
- RAM: 128MiB (Nanya NT5CC64M16GP-DI)
- ROM: 128MiB NAND Flash (Macronix MX30LF1G18AC-TI)
- Wireless:
for 11b/g/n (upto 300Mbps): MT7603
for 11a/ac (upto 1450Mbps) : MT7615, is not avaliable now
- Ethernet LAN speed: up to 1000Mbps
- Ethernet LAN ports: 4
- Ethernet WAN speed: up to 1000Mbps
- Ethernet WAN ports: 1
- USB ports: 1 (USB 2.0)
- LEDs: 4 (all can be controlled by SoC's GPIO)
- buttons: 2
- serial ports: unknown
Installation through telnet:
- Copy kernel.bin and rootfs.bin to a USB flash disk,
plug to usb port on the router.
- Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
(login if required, default: admin password)
- You will see "Debug Enabled!"
- Telnet 192.168.1.1 and login with "root"
- ls /mnt/shares/ to find out path of your USB disk.
'myUdisk' for example.
- cd /mnt/shares/myUdisk
- mtd_write write rootfs.bin Rootfs
- mtd_write write kernel.bin Kernel
- reboot
recovery when bricked:
nmrpflash can be used to recover to the netgear firmware
if a broken image was flashed.
The SC_PART_MAP partition suggests that an on flash partition table
exists. After implementing a partition parser/builder for the sercom
partition format, the definitions don't match the flash layout used by
the stock firmware.
It either means the partition format has not yet been completely
understood or it isn't used by the stock firmware. For now, use fixed
partitions instead.
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[apply latest ramips changes and document the on flash partition map
issues]
Signed-off-by: Mathias Kresin <dev@kresin.me>
- Mark other partitions as read-only for HC5x61
- Only enable USB and PCIe for HC5761/HC5861
HC5661 doesn't have a USB port, and there is nothing attached to its PCIe.
- Fix HC5761 switch ports
HC5761 has only 3 ethernet ports (1x WAN + 2x LAN). Remove unused ports.
- Fix HC5861 5GHz radio
HC5861 has MT7612EN 5GHz WiFi chip, not MT7610EN.
- Fix HC5761/HC5861 WiFi LEDs
After 5GHz is enabled, it becomes wlan0. And 2.4GHz would be wlan1.
- Fix HC5x61 image size
It should be 15872k (0xf80000)
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
It's no longer needed as all mt7621 devices use DT binding (supported by
upstream mtd code) for specifying "firmware" part format explicitly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Due to the enforced image metadata we ensure that the correct image is
uploaded. Checks based on a magic arn't required any more.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Beside one exception, no one took care of these two remaining boards
still using the legacy image build code during the last two years.
Since OpenWrt 14.07 the ALLNET ALL0239-3G image building is broken.
The Sitecom WL-341 v3 image build code looks pretty hackish and broken.
It's questionable if the legacy image works as all.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop the factory images and the firmware tool to create them. They don't
work any more, since the factory image has an uImage header covering the
whole kernel + rootfs. This way the uImage splitter will not be able to
find the rootfs and the kernel will panic later on.
The factory images were most likely added at a time the board had
distinct partitions for kernel and rootfs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In commit d70ec3008d, a firmware compatible
string of "denx,uimage" was added for the Dlink DIR-860L-B1. Unfortunately,
this was the wrong string. It needs "seama" instead.
Signed-off-by: Russell Senior <russell@personaltelco.net>
The latest dtc compiler considers nodes named i2c or spi as the
respective bus:
/pinctrl/i2c: incorrect #address-cells for I2C bus
/pinctrl/spi: incorrect #address-cells for SPI bus
Rename the node to fix the false positives.
Fix the spi node unit address for the DWR-512-B and UBNT-ER-e50 to get
rid of the following warning:
SPI bus unit address format error, expected "n"
Signed-off-by: Mathias Kresin <dev@kresin.me>
Select the matching mt76 driver for the PCI wireless of the following
devices:
- HiWiFi HC5861B
- Mercury MAC1200R v2.0
- Netgear AC1200 R6120
- Buffalo WCR-1166DS
- ZyXEL Keenetic Extra II
- Wavlink WL-WN575A3
Because every device has selected the corresponding mt76 driver, we can
include kmod-mt7603 instead of the mt76 metapackage, which used for the
wireless of the mt7628 and mt7688 WiSoC.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[select kmod-mt7603 as target default package, add wireless driver for
WL-WN575A3]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Currently OpenWrt doesn't support switching MT7628 into AP mode
(which is done by writing some undocumented registers in MTK SDK)
Without doing so, enabling SD breaks 4 FE ports and the SD controller
doesn't work since SD pins aren't configured correctly.
Disable SDHC on HC5661A to recover the 4 FE ports.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[drop the sdhci node completely]
Signed-off-by: Mathias Kresin <dev@kresin.me>
I wanted to add status LEDs support to my imx6 based board and have found out,
that I could use diag.sh script found in ramips platform, which seems to be
also shared in a few other platforms:
4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh
And @chunkeey suggested to me, that I can also add lantiq, ipq806x and
apm821xx to the list of platforms which could share this generic
diag.sh.
I've extended the base diag.sh in a way, that if it detects any of the
DTS LED aliases, then it would use the generic DTS set_led_state code.
The code in platform's diag.sh has moved to base-files package in this
commit:
base-files: diag.sh: Make it more generic towards DTS so it could be reused
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
The DWR-118-A1 Wireless Router is based on the MT7620A SoC.
Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 3x 10/100 Mbps Ethernet (3 LAN)
- 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN)
- 1x internal, non-detachable antenna
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader
Known issues:
- WIFI 5G LED not working
- flash is very slow
The status led has been assigned to the dwr-118-a1:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.
Installation:
Apply factory image via http web-gui or JBOOT recovery page
How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Because every device has selected the corresponding mt76 driver, we can
now disable the mt76 metapackage by default to make sure that other
devices (those don't need mt76) avoid selecting unwanted packages.
We can find the hardware specifies and determine the dependencies on
these sites:
https://wikidevi.com/wiki/https://openwrt.org/toh/hwdata/
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
All boards neither expose the PCIe as Mini-PCIe nor have anything
attached to the PCIe Bus. Disable PCIe for those by dropping the node
from the dts files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Compile the loader if the relocate-kernel image recipe is used and get
rid of the legacy build code to do so.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specify firmware partition format by compatible string.
List of devices:
-DWR-116-A1
-DWR-118-A2
-DWR-512-B
-DWR-921-C1
-LR-25G001
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
MTC Wireless Router WR1201 is the OEM name of the board. It is also sold
rebranded as STRONG Dual Band Gigabit Router 1200.
Specification:
- SoC: MediaTek MT7621A (880 MHz)
- Flash: 16 MiB
- RAM: 128 MiB
- Wireless: 2.4Ghz(MT7602EN) and 5Ghz (MT7612EN)
- Ethernet speed: 10/100/1000
- Ethernet ports: 4+1
- 1x USB 3.0
- 1x microSD reader
- Serial baud rate of Bootloader and factory firmware: 57600
The OEM webinterface writes only as much bytes as listed in the
uImage header field to the flash. Also, the OEM webinterface
evaluates the name field of uImage header before flashing (the
string "WR1201_8_128")
To flash via webinterface, is mandatory to use first initramfs.bin
and after (from the OpenWrt) the sysupgrade.bin
Some notes:
- Some microSD will not work:
mtk-sd 1e130000.sdhci: no support for card's volts
mmc0: error -22 whilst initialising SDIO card
mtk-sd 1e130000.sdhci: no support for card's volts
mmc0: error -22 whilst initialising MMC card
mtk-sd 1e130000.sdhci: no support for card's volts
mmc0: error -22 whilst initialising SDIO card
mtk-sd 1e130000.sdhci: card claims to support voltages below defined range
mtk-sd 1e130000.sdhci: no support for card's volts
mmc0: error -22 whilst initialising MMC card
mtk-sd 1e130000.sdhci: no support for card's volts
mmc0: error -22 whilst initialising SDIO card
mtk-sd 1e130000.sdhci: no support for card's volts
mmc0: error -22 whilst initialising MMC card
Signed-off-by: Valentín Kivachuk <vk18496@gmail.com>
Specify firmware partition format by compatible string.
formats in ramips:
- denx,uimage
- tplink,firmware
- seama
It's unlikely but the firmware splitting might not work any longer for
the following boards, due to a custom header:
- EX2700: two uImage headers
- BR-6478AC-V2: edimax-header
- 3G-6200N: edimax-header
- 3G-6200NL: edimax-header
- BR-6475ND: edimax-header
- TEW-638APB-V2: umedia-header
- RT-N56U: mkrtn56uimg
But it rather looks like the uImage splitter is fine with the extra
header.
The following dts are not touched, due to lack of a compatible string in
the matching firmware splitter submodule:
- CONFIG_MTD_SPLIT_JIMAGE_FW
DWR-116-A1.dts
DWR-118-A2.dts
DWR-512-B.dts
DWR-921-C1.dts
LR-25G001.dts
- CONFIG_MTD_SPLIT_TRX_FW
WCR-1166DS.dts
WSR-1166.dts
- CONFIG_MTD_SPLIT_MINOR_FW
RBM11G.dts
RBM33G.dts
- CONFIG_MTD_SPLIT_LZMA_FW
AR670W.dts
- CONFIG_MTD_SPLIT_WRGG_FW
DAP-1522-A1.dts
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Use .bin as file extension where possible. The user doesn't need to that
sysupgrade images for NAND boards are tarballs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Having MIT as alternative is sometimes preferred by upstream maintainers
and allows sharing that simple code with other projects. We don't really
want multiple DTS versions for the same device.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The previous offset was invalid and pointed to the end of the partition,
which was causing issues with mt76
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The 5GHz radio of this device uses an mt7610e PCI-E chip, which has
been recently started to be supported.
mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
mt76x0e 0000:01:00.0: ASIC revision: 76100002
mt76x0e 0000:01:00.0: Firmware Version: 0.1.00
mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specify firmware partition format to denx,uimage in compatible DTS property.
2 uimage-fw partitions found on MTD device firmware
Creating 2 MTD partitions on "firmware":
0x000000000000-0x00000017f72b : "kernel"
0x00000017f72b-0x000000f70000 : "rootfs"
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Flash partitions were moved under partition table node, but addition of
compatible property was omitted which lead to following boot failure:
VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
1f00 16384 mtdblock0
(driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Fixes: e4d9217f (ramips: improve BDCOM WAP2100-SK support)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The 5 GHz radio of this device uses an mt7610e pci-e chip, which has
been recently added support.
Tested on the actual device as AP and client, TCP throughput ~90 Mbps
U/D.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Add support for UniElec U7621-06 variant with 512MB RAM and 64MB flash.
Additional specs are below:
CPU: MT7621 (880Mhz)
Bootloader: Ralink U-Boot
Flash: 64MB
- U-Boot identifies as Macronix MX66L51235F
- kernel identifies as MX66L51235l (65536 Kbytes)
RAM: 512MB
Rest of the details as per commit 46ab81e405 ("ramips add support for
UniElec U7621-06")
Signed-off-by: Nishant Sharma <nishant@unmukti.in>
[use generic board detection, add firmware partition compatible, extend
firmware partition to use all of the remaining flash space, add a
maximum image size matching the firmware partition size]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the generic board detection for the board instead of the target
specific one. Mark the sysupgrade image compatible with the former used
userspace boardname to allow an upgrade from earlier versions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The RavPower WD03 is a mt7620n based baord. With the change applied, I2C
should work now with the RavPower WD03.
Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
With ed25e3ac02 ("ramips: fix some clocks in mt7621.dtsi") the
cpuclock node was dropped from the mt7621.dtsi without removing the
references to this node from the GB-PC1/PC2 dts files.
Remove them now, to fix the build error.
Signed-off-by: Mathias Kresin <dev@kresin.me>
It has to be <board>:<colour>:<function> and is expected exactly this
way by the userspace scripts.
While at it, fix some whitespace issues in the dts file and rename the
flash node as required upstream.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the generic board detection instead of the target specific one as
all recent additions are doing.
Setup the USB led via devicetree (a58535771f) and include the required
driver by default. Merge the led userspace setting with an existing
identical case.
Use the wps led for boot status indication.
Move the partitions into a partition table node (6031ab345d) and drop
needless labels. Drop misplaced cells properties (53624c1702).
Cleanup the pinmux and only switch pins to gpio functions which a
referenced as gpio in the dts.
Match the maximum image size with the size of the firmware partition.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The sd function of the nd_sd group configures two of the groups pins as
gpios. The pins are used as PCIe reset/power.
Due to the driver load order, the pins are configured way to late if
triggered by the sd-card driver.
To not introduce another kind of driver load order dependency and
configure the pins as early as possible, means during pinmux driver
load.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Weijie Gao