This patch adds support for Huawei E970 wireless gateway devices.
It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV.
E960/B970 should work too, from what I know it's basically the same hardware.
The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem.
It uses a hardware watchdog which needs GPIO-7 to be toggled at least
every 1-2 seconds. This patch uses gpio_wdt module (see my previous
patch today) to take care of this.
Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset
button, image to be used for upgrade from OEM firmware's web interface
Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970>
Issue:
* lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog
reset during kernel decompress.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
SVN-Revision: 38011
In order to support both normal images and initramfs, ensure that each
target sets KERNELNAME properly so that the generic kernel building code
can copy the corresponding files over $(KDIR) with the appropriate
extension. Update the various paths to the kernel and wrapper images
from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37049
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it
was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and
LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the
bootloader and stock firmware will accept.
The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving
its LEDs through an HC164 8-bit shift register.
Signed-off-by: Owen Kirby <osk@exegin.com>
SVN-Revision: 36482
WNDR3400v2 is based on BCM53xx . Image that is created breaks the router somehow therefore "#".
CFE and NVRAM contain different vars - example:
CFE line original: Device eth0: hwaddr 74-44-01-37-C6-69, ipaddr 192.168.1.1, mask 255.255.255.0
CFE after openwrt: Device eth0: hwaddr 00-FF-FF-FF-FF-FF, ipaddr 192.168.1.1, mask 255.255.255.0
Logs were posted earlier on this mailing list: https://lists.openwrt.org/pipermail/openwrt-devel/2012-July/016174.html
Different logs with factory firmware are in the wiki: http://wiki.openwrt.org/toh/netgear/wndr3400#wndr3400v2
(and on wikidevi for example)
Signed off by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 35790
2.4 isn't present anymore, so it will always be 2.6 (or newer). Since the
2.6 check will break with 3.0, remove it alltogether.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 27185
CFE does not boot images generated with these checksums because of
wrong checksum.
After flashing then with tftp to my Asus wl500-GPv1 the following messages
are show:
Null Rescue Flag.
Boot program checksum is invalid
Hello!! Enter Rescue Mode: (Check error)
SVN-Revision: 22418
* reduce image size for CRC calculation by fs_mark size
sysupgrade sometimes failed for me and I noticed that it was due
to incorrect CRC values in trx-header after performing it.
It seems that the fs_mark was completely included in the calculation
and that it was nevertheless modified by sysupgrade while appending
the jffs data.
This only occurs for the first boot after sysupgrade as the flashmap
driver recalculates the CRC to an even smaller area when it boots.
SVN-Revision: 22396
'factory' and 'sysupgrade' did not make much sense. A discussion
with jow convinced me that .trx results in a helpdesk disaster.
So I decided to use '.bin' for normal bin-headers and '.noheader.bin'
for the trx-v2 image.
I fixed the wiki accordingly.
SVN-Revision: 22013
- hacked addpattern due to changes in header format
- added "-5" to addpattern, some 0xFF are needed for trx2 header
"-4" broke CRC checking in CFE
- hacked trx.c due to new header format version
- added target to create trx-V2 images
the flashmap driver possibly needs to be customized.
SVN-Revision: 20433
We switched over to appending the jffs2 eof mark to the squashfs images,
but since the squashfs is not always aligned to eraseblocksize, the eof
mark landed in the wrong place. This commit adds an extra flag to the
trx utility that can append extra data to a partition with alignment.
This is used to place the jffs2 eof mark at the right offset.
SVN-Revision: 7253
Hauke Mehrtens