This aligns default network interfaces configuration with vendor
firmware: GE (eth0) -> wan, FE (eth1) -> lan.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GMAC0 interface of AR9344 SOC in Wallys DR344 board is connected with
AR8035, not with AR8327. Without this fix, GE interface doesn't work at
all or shows high packet loss ratio.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.
The device is based on Qualcomm/Atheros AR9341 v1.
Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button
Flash instructions:
You have three options:
- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.
- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.
- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:
*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
stat -- Status
sys -- System
wless2 -- 2.4G-Wireless
mgmt -- Management
tree -- Tree
help -- Help
reboot -- Reboot
ens202ext>mgmt
Management
---========= Commands Help =========---
admin -- Administration
mvlan -- Management VLAN settings
snmp -- SNMP settings
backup -- Backup/Restore settings
autorb -- Auto reboot settings
fwgrade -- Firmware upgrade
time -- Time settings
wifisch -- Wifi schedule
log -- Log
diag -- Diagnostics
disc -- Device Discovery
logout -- Logout
help -- Help
exit -- Exit
ens202ext/mgmt>fwgrade
Management --> Firmware upgrade
---========= Commands Help =========---
fwup -- Firmware upgrade
help -- Help
exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin
Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
The single SFP port is meant for direct media access to WAN, such as
VDSL2, GPON). While it could also be used for in-home fiber, it is much
more likely that the LAN is standard ethernet, especially considering
that SFP is the onmly port that can go beyond 1Gbps.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Take explicit note of what physical ports eth{0,1,2} refer to.
Also repair port assignment:
At some point between 4.9.20 and 4.9.29 the numbering changed.
Keep previous port assignment that was:
LAN = SFP+Switch
WAN = standalone ethernet
Also use the same assignment for Clearfog-Base to avoid confusion.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Installing all armada-388-clearfog-* DTBs in the same sdcard image,
it now becomes much easier to swap sdcards between different device variants.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
U-Boot provides standard variables for load addresses, and
filesystem-agnostic load-commands. Furthermore thanks to distro-boot,
the device and partition from which the system boots is known.
The new boot-script makes use of all this information.
Tested on the only board that uses this boot-script: Clearfog Pro
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Add a patchfile that implements distro-boot and is meant to go upstream
Also make the other patches git-am'able for easier maintenance.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
This fixes GCC 7 compilation when GRAPHITE is selected.
The path is replaced with $(TOOLCHAIN_DIR), while it should be
$(STAGING_DIR_HOST). To keep in sync with the path of gmp,
mpfr and mpc, I'm using $(TOPDIR)/staging_dir/host.
Fixes: f62f4b3c5c ("build: stop overriding STAGING_DIR_HOST for toolchain build")
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
sunxi sysupgrade was based on the x86 implementation; sync fixes and other
changes from the current x86 version:
x86: fix sysupgrades on disks with 4k block size
x86: sysupgrade: move partition table change check to platform_check_image
x86: sysupgrade: refactor platform_do_upgrade
x86: sysupgrade: explicitly rescan disk after writing partition table
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
When existing partitions are retained, the dd call writing the uboot image
in the space before the first partition was accidentally writing the whole
image, making the code for individual partitions redundant. Limit the copy
to 1016KiB (the first 8KiB are skipped, and the first partition starts at
1024KiB).
In addition, conv=notrunc is replaced with conv=fsync. It seems this was an
oversight, as notrunc doesn't make sense for block devices and all other dd
commands use conv=fsync.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This should ensure that the kernel partition can be mounted in
platform_copy_config when its size has changed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
By returning early when no upgrade device can be found and handling the
SAVE_PARTITIONS=0 case differently, we can get rid of two levels of if.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The staged sysupgrade will prevent us from using ask_bool in
platform_do_upgrade; therefore, the check is moved to platform_check_image.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
All targets with NAND support should gradually move their nand_do_upgrade
calls from platform_pre_upgrade to platform_do_upgrade.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some functions only used by stage2 are moved there from common.sh.
One piece that could still use more cleanup is platform_pre_upgrade: many
targets reference files from there are aren't available in the ramfs, so
we need to evaluate it before the switch; conversely, flash writes happen
in that function on some targets. Targets that do the latter should be
fixed eventually to use platform_do_upgrade for that purpose.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
We can reuse the kill_remaining and run_ramfs facilities of the stage2 run
by upgraded.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Support for the -d and -p options is dropped; it may be added again at some
point by adding these flags to the ubus sysupgrade call.
A downside of this is that we get a lot less information about the progress
of the upgrade: as soon as the actual upgrade starts, all shell sessions
are killed to allow unmounting the root filesystem.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
We always want to support staged upgrades now, so it's better to include
upgraded into the main package. /lib/upgrade/nand.sh is moved to
base-files.
The procd-nand-firstboot package is removed for now, it may return later
as a separate package.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
992b796 rcS: add missing fcntl.h include
63789e5 init: add support for sysupgrades triggered from preinit
5b1fb35 Remove code that has become unnecessary after sysupgrade changes
5918b6d upgraded: add support for passing a "command" argument to stage2
056d8dd upgraded: link dynamically, chroot during exec
7c6cf55 system: always support staged sysupgrade
d42b21e procd/rcS: Use /dev/null as stdin
e0098d4 service/instance: add an auto start option
1247db1 procd: Log initscript output prefixed with script name
8d720b2 procd: Don't use syslog before its initialization
2555474 procd: Add missing \n in debug message
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Use install_bin to copy upgraded with all dependencies. The old name
/tmp/upgraded is temporarily retained as a symlink to avoid breaking
things.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Insight hasn't been touched since 2009 and I can't find any references at
least 6 years back of being used. Ubuntu and Debian removed insight years ago
from their repos so I think we can safely remove this too.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
This change adds QPIC BAM dma and NAND driver node's in IPQ4019
device tree, also enable this for AP-DK04.1 based boards.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
This change adds support for below:
- Bam transaction which will be used for any NAND request.
- Reset function for NAND BAM transaction
- Add support for additional CSRs.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
The existing qcom_nand driver supports ADM DMA which is mainly
required for ipq806x family based boards,
IPQ40xx based boards uses BAM DMA in NAND driver, so this patch
adds BAM DMA support with compatible string as qcom,ebi2-nandc-bam.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
GPIO_PULL bits configurations in TLMM_GPIO_CFG register
differs for IPQ40xx from rest of the other qcom SoC's.
This change add support to configure the msm_gpio_pull
bits for ipq40xx, It is required to fix the proper
configurations of gpio-pull bits for nand pins mux.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
The previous commit introduced a faulty continue statement which might
lead to faulty rules not getting freed or reported.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update to latest Git HEAD in order to import a number of fixes and other
improvements:
3d2c18a options: improve handling of negations when parsing space separated values
0e5dd73 iptables: support -i, -o, -s and -d in option extra
4cb06c7 ubus: increase ubus network interface dump timeout
e5dfc82 iptables: add exception handling
f625954 firewall3: add check_snat() function
7d3d9dc firewall3: display the section type for UBUS rules
53ef9f1 firewall3: add UBUS support for include scripts
5cd4af4 firewall3: add UBUS support for ipset sections
02d6832 firewall3: add UBUS support for forwarding sections
0a7d36d firewall3: add UBUS support for redirect sections
d44f418 firewall3: add fw3_attr_parse_name_type() function
e264c8e firewall3: replace warn_rule() by warn_section()
6039c7f firewall3: check the return value of fw3_parse_options()
Fixes FS#548, FS#806, FS#811.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The generic preinit code is now able to setup network and switch vlan settings
from the /etc/board.json file, therefor drop the target specific code.
Fixes FS#790.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The previous CVE bugfix commit did not adjust PKG_RELEASE, therefor the
fixed samba package does not appear as opkg update.
Bump the PKG_RELEASE to signify upgrades to downstream users.
Ref: https://forum.lede-project.org/t/sambacry-are-lede-devices-affected/3972/4
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Piotr Dymacz