most symbols should be in Kernel packages
depending on HW the removal of
CONFIG_REALTEK_PHY
and USB symbols might be wrong
compile tested only
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
the support is still WIP. next steps are to make the pmic and ethernet work.
this is the first commit to make sure nothing gets lost.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47354
To use gpio leds as ide leds, we need to enable the trigger to be
included in the kernel.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46795
*Enable SMEM MTD parser and its dependencies (SMEM & HW spinlocks) in
the kernel config
*Replaces the MTD layout in DT by the dynamic layout provided by the
SMEM parser for AP148
Using the OF based parser is still possible on platforms which have a
fixed MTD partition layout.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46658
Previous patch set backported the recently posted NAND flash driver to
3.18 and 4.1 kernel. This patch now enables it in the kernel config.
There is no change to the partition layout and init yet. But the NAND
flash can be seen in the mtd list on an AP148:
root@OpenWrt:/# cat /proc/mtd
dev: size erasesize name
mtd0: 10000000 00020000 "qcom-nandc"
...
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46569
These are cherry-picked & backported from LKML:
*https://lkml.org/lkml/2015/3/17/19
They are enabled on both 3.18 and 4.1 kernel. Patches 150 to 154 are
applying changes merged since 3.18; they enable mechanisms used by the
ADM driver.
ADM engine is used by the NAND controller, so it is necessary to
bring-up NAND flash support.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46567
We forgot to enable the stmmac driver for 4.1 kernel, so ethernet
interfaces don't show-up on this kernel.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46559
Most ipq806x platforms use an ethernet switch, and the new upstream
GMAC driver makes use of the Fixed PHY emulation to force the link
settings despite the lack of PHY.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45830
Patches are cherry-picked from linux-next. We're also adding the
corresponding config option to the kernel.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45729
This change adds PCIe support to IPQ806x based platforms. The driver is
actually cherry-picked from the following LKML thread:
*https://lwn.net/Articles/643086/ (patches 110-111)
We also add here an additional fix to support multiple PCI controllers
on the same platform (patch 112), and to patch the ap148 & dbs149 DTS
files (patch 113).
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45663
This change enable zImage+appended dtb support in ipq806x kernel
options. The zImage will now be generated as part of the kernel
binaries. Platforms which do not have DT support enabled in U-boot
can now make use of it by generating zImage files and appending dtb
to it.
It is not used yet but it is done as a stepping stone for early IPQ806x
platforms, which did not include DT support in U-boot.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45662
Certain IPQ806x based platforms are making use of this PHY. So we'll
enable it so it gets detected as such.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45535
This change doesn't make USB functional but it does make it selectable
from a configuration perspective.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45259
Options that used to be in target config have been added to the generic
config file, so remove them.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45255
This patch allows AP148 to boot from NOR flash.
As we're using a FIT image as kernel (which includes kernel bin + DTB)
we enable the MTD_SPLIT_FIT_FW kernel option, which will detect the FIT
image and automatically split the "firmware" partition into 2 MTD parts
(kernel + rootfs).
The rootfs will then be parsed and split between rootfs + rootfs_data,
as usual.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44794
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44614
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44612
Some bootloaders seem to trigger the watchdog during the boot process,
therefore the lack of watchdog driver trigger a reboot a few seconds
after boot. So we'll enable it here to avoid it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44503
Patches in the ipq806x/patches folder were out of tree in v3.14. The
newest patch at the time was from June, so we can safely assume that
either the patches have been merged, or they have been rejected for
a good reason. If patches are seen missing, we'll cherry-pick them
on a per-needed basis.
This new kernel have been tested on AP148, which seems to works fine.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44386
Patches are generated using the "format-patch" command from the
following location:
*https://www.codeaurora.org/cgit/quic/kernel/galak-msm/log/?h=apq_ipq_base
*rev=0771849495b4128cac2faf7d49c85c729fc48b20
Patches numbered 76/77/102/103 have already been integrated in 3.14.12,
so they're not in this list.
All these patches are either integrated are pending integration into
kernel.org, therefore these patches should go away once the kernel
gets upgraded to 3.16.
Support is currently limited to AP148 board but can be extended to other
platforms in the future.
These changes do not cover ethernet connectivity.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 42334
The OpenWrt build system uses MACHINE_FEATURES of fpu to set the HAS_FPU which
in turn sets the default of CONFIG_SOFT_FLOAT as well as uClibc configuration.
As the IMX6 SoC has both vfpv3 and NEON hardware support we want to add fpu
to the feature list. This will default the IMX6 target to use -mfloat-abi=hard
which will the be most efficient use of floating point.
When switching to hard float, we also need to enable VFP support in the kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39759
DMA and SDMA support are needed for ssi based audio. Note that the sdma
firmware is no longer required for ssi audio.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39011
Enable SATA support (for IMX6D/IMX6Q) static in the kernel. It seems there
are some issues causing the driver to not load properly when built as
a module which still need to be worked out.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 38515
John Crispin