Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.
To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:
VR9 # run reset_uboot_config
VR9 # reset
VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The mac address is printed on the label at the bottom of the case.
The following steps are need to be done during first install:
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.
Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.
A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WBMR boards are the only ones in the whole tree selecting the wpad
and hostapd-utils package by default.
Remove the wps uci-default script as well, there is no obvious reason
why the wps config need to be set only for this board.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In case the adsl/vdsl service is disabled intentional, the output is
cluttered with the following message multiple times if the status of
the dsl line is queried:
killall: vdsl_cpe_control: no process killed
If the dsl line status is queried by LuCI, the logfile is spammed with
the message.
Fix the issue by using killall in quite mode. In quite mode killall
still returns a non-zero value if the to be killed process can not be
found so that existing logic based on the return value still works.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use a more generic name for the lantiq_get_dt_led_chosen function.
Drop the lantiq_is_dt_led_chosen function. The lantiq_get_dt_led
function can be used to achieve the same.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add or fix the physical port number of switch ports to allow LuCI to
display the ports in physical order.
Remove the physical port number in case bridge port and physical port
order are the same.
Reorder the ucidef_add_switch parameter to be aligned with the switch
port number.
Remove board settings which are covered by the default case and remove
comments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not set the lan mac address for boards which having the lan mac
address already set in device tree source file.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The device tree description misses some Ethernet ports and there was no
model specified for this board. In addition there was no switch
specific default configuration created.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
So far the network in failsafe is setup only for one board. Use the
eth0 interface as lan interface for all boards for now.
If a board has its lan interface(s) on another eth, a special
handling based on the board name can be added.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Ethernet, ADSL2+ and LEDs are fully functional.
Supporting the two TAE ports and SIP gateway was not attempted.
The WiFi is unreliable, due to experimental support for rt35xx family
devices by the rt2800pci driver.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
[rebase to LEDE HEAD]
[switch to normal image instead of brnboot image]
[remove not required pinmux child nodes keys, leds, ebu, exin, pci_in and pci_out]
[remove switch_rst pinmux child node (no support for hw reset in driver/setting a default GPIO value in DT]
[enable usage of the wireless LED]
[fixup mac address configuration]
Sgned-off-by: Mathias Kresin <dev@kresin.me>
This patch is a follow up to commit 4cf3fd4 "add support for indicating
the boot state using three leds".
At the time of writing the patch, I wasn't aware that it's possible to
switch info failsafe after boot (factory reset).
Enabling the failsafe led without disabling the running led causes an
unexpected led colour on devices using a single multicolour led to
indicate the boot state.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch fixes the missing Lan interface config in the file
/etc/config/network for ARV4518PWR01/A which results in eth0 and br-lan
being down and therefore no way to access the router unless via UART-TTL.
Signed-off-by: Mohammed Berdai <mohammed.berdai@gmail.com>
Avoids inadvertent file creation when executing
`/etc/init.d/dsl_control status`.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
SVN-Revision: 48700
This adds basic support for TP-Link VR200v.
Currently the following parts are not working: FXO, Voice, DECT, WIFI (both)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48328
The leds of the following boards are not renamed due to lack of
manuals/informations:
- ARV7519PW
- ARV7510PW22
- ARV4510PW
The leds of the ARV4518PWR01* boards are unchanged, since the leds doesn't
match the leds from the manual or pictures (e.g. there shouldn't be a wps led).
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48042
The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to
indicate the current boot state. This patch adds support for such cases.
The existing led sequences should be the same as before.
Boards which are using a led different from power (like TDW89x0) are
changed to switch of the led after boot
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48041
dsl_control (dsl_notify.sh) is the only process which is aware of the
state of the atm/ptm interface. Use the dsl led exclusive for the dsl
line state.
On boards which don't have a distinct internet and a dsl led, let the
netdev status of the atm interface trigger the shared led.
Triggering the shared led according to the status of the ppp interface
isn't suitable, since the led would be switched of if the ppp
connection goes down, but the line is still in sync.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48040
Remove all now double defined leds from the led board file. Use pppoe
as default for all broadband connections, since it's the default in
OpenWrt now.
Rename the the wifi leds to make sure, the not applicable default
values get overwritten.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48038
- Use common OpenWrt blink patterns instead of custom ones
- Add preinit_regular hook
- Handle the TDW89X0 that does not have a configurable power LED
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 47914
Mathias Kresin