r46161 updated headers also touched by it, so it needed to be refreshed
as well.
Closes#20033.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46165
Make some network uapi headers detect if they are included after
not only glibc but also musl headers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46161
Also move it to an earlier place so new boards added are less likely
to confuse quilt.
Fixes#19965.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46148
Follow upstream patch and handle it using &uart0. Also disable &uart1 as
it's most likely unused. This will allow us to get valuable reports and
upstream these changes.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46140
This patch adds the missing parts to use the upstream Broadcom PCIe
driver and makes use of it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46130
Instead of setting the l2c_aux_val variable in the board code make it
possible to set these through device tree and make use of that.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46129
This only removes the patches already applied upstream and makes the
rest apply cleanly.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46128
TP-Link ships wr740n v5.0 to Romania (so probably everywhere except
China) with 4 MB flash and 32 MB memory (confirmed by their local
support). This patch adds support for the v5.0 clone of v4, i just
tested it on my own v5.0 router and it works.
Signed-off-by: Daniel Petre <daniel.petre@posteo.net>
SVN-Revision: 46115
Boot tested: http://pastebin.com/L6aAb9xj
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo:
update to 4.1 final
add patches added since submission
delete patches applied in later rcs
restore commit messages in 220-gc-sections and 304-mips_disable_fpu
fix 050-backport_netfilter_rtcache to match new API
update inlined dma ops with upstream changes
add missing config symbols
enabled CONFIG_MULTIUSER
update kmod defintions for 4.1
]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46112
On two tested devices: Netgear R6250 (BCM53011 rev 2) and Luxul XWC-1000
(BCM53011 rev 3) it was possible to use port 7 and eth1 (instead of port
5 and eth0). It seems BCM53011 just like BCM53012 has 8 ports and
usually 3 of them are connected to the SoC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46104
The hardware should be almost the same as TL-WR720N-v3. WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>". Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 46046
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
SVN-Revision: 46044
This patch adds support for the Linksys RE6500 Range Extender
http://wiki.openwrt.org/toh/linksys/re6500
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46043
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.
Signed-off-by: tymon <banglang.huang@foxmail.com>
SVN-Revision: 46041
Some devices ship with NAND images that use BCH ECC. Let the driver know
about that ECC mode so that it can be selected by machine files.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
SVN-Revision: 46022
It seems that there are maximum timings for mdio accesses that can be
hit when the system is under load and the thread is scheduled during
a read or write access. Since there is no way of knowing if this
happens as there is not even a parity bit, try to work around it
by disabling interrupts during any gpio-mdio accesses.
Performance impact seems to be neglectable, as mdio accesses are not
that often.
Hopefully fixes#19500.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46012
This stabilizes USB support. The old patch was handling initialization
in a different order that was causing some problems with few USB 3.0
devices. Some weren't detected, some were working unstable, sometimes
USB 3.0 could hang the whole controller.
A still known issue (but not a regression) is controller hang triggered
by connecting USB 1.1 device when not having OHCI controller enabled
(kmod-usb-ohci).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45997
Hauke Mehrtens