Several devices in mt76x8 subtarget use the following line to set
up wmac in their DTS(I) files:
ralink,mtd-eeprom = <&factory 0x4>
This is strange for several reasons:
- They should use mediatek,mtd-eeprom on this SOC
- The caldata is supposed to start at 0x0
- The parent DTSI mt7628an.dtsi specifies mediatek,mtd-eeprom anyway,
starting from 0x0
- The offset coincides with the default location of the MAC address
in caldata
Based on the comment in b28e94d4bf ("ramips: MiWiFi Nano fixes"),
it looks like the author for this device wanted to actually use
mtd-mac-address instead of ralink,mtd-eeprom. A check on the same
device revealed that actually the MAC address start at offset 4 there,
so the correct caldata offset is 0x0.
Based on these findings, and the fact that the expected location on
this SOC is 0x0, we remove the "ralink,mtd-eeprom = <&factory 0x4>"
statement from all devices in ramips (being only mt7628an anyway).
Thanks to Sungbo Eo for finding and researching this.
Reported-by: Sungbo Eo <mans0n@gorani.run>
Fixes: b28e94d4bf ("ramips: MiWiFi Nano fixes")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 09d38a3bc328d122b0d84fcf6bb53d2bce7373b6)
led2l and led2h value is incorrectly set by led3l and led3h.
Bug was introduced in commit: 863e79f8d5
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Fixes: 863e79f8d5 ("lantiq: add support for kernel 4.9")
(cherry picked from commit 692390225d76de8f2daf582454e74942b82d090a)
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:
OpenWrt: lan = label_mac -2, wan = label_mac -2
stock: lan = label_mac, wan = label_mac +1
This patch applies to all devices using TL-WDR4300 board:
TL-WDR3600 v1
TL-WDR4300 v1
TL-WDR4300 v1 (IL)
TL-WDR4310 v1
Mercury MW4530R v1
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 9b02d32e34df2bb8821ec6f08f525bee22d0d1ba)
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:
OpenWrt: lan = label_mac -2, wan = label_mac -2
stock: lan = label_mac, wan = label_mac +1
The full address assignment is as follows:
LAN label
WAN label + 1
5G label
2G label - 1
This patch changes all devices using TL-WDR4300 board:
TL-WDR3600 v1 (checked on device)
TL-WDR4300 v1 (checked on device)
TL-WDR4300 v1 (IL)
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rephrase/extend commit title/message, backport]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a4260eaab7744c8e3f1f7a62a61aab5e3b562342)
Device support for Belkin F9K1109v1 was added using set_usb_led()
although this was removed in 772b27c207 ("ramips: set F5D8235 v1
usb led trigger via devicetree").
Use ucidef_set_led_usbport() instead.
Fixes: f2c83532f9 ("ramips: add support for Belkin F9K1109v1")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rephrase commit title and message, backport]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 1f455418ef1ea67fda710e1b86a9e021bb4a2413)
TL-WDR4300 board uses only green LED names in DTSI.
This patch adds migration for them.
The actual LED colors on the devices have been reported to vary
across subrevisions (v1.x). Despite, the USB LEDs on the back might
have different color than the other LEDs on the front.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 01d39cd18c4035e362f179548cd2c051aac03042)
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit e964338110526b3692847769343816cd2f853d18)
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2105354968ed9698709d220ec446b6d9c27da3a5)
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 414d027ae8ac05ec9aa06bc50afd5458c2da02fc)
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 411e824ec371a322b975e90af5a1f32760a61720)
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c1db4d9c5655e3c74ffdbb6a6a3367269f65c55f)
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d0d7f5d9e49b8632f372c92e0339895fa10904f9)
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit dcf48fda054c4bbc52f6106250a7e06ab8f5cbdd)
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c881769a558b38ddd5977a50b67cd32c6d3f7d5e)
The led wireless trigger is already set correctly to phy0tpt through the
alias in the device tree.
Signed-off-by: Manuel Kock <github.web@manu.li>
[rephrased commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 509894cffb7ec24ac21a381bed3c035efce42aeb)
Hardware
--------
SoC: NXP P1020 (2x e500 @ 800MHz)
RAM: 256M DDR3 (Micron)
FLASH: 32M NOR (Spansion S29GL128S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 1x Gigabit Ethernet (Atheros AR8033)
LED: System (green/red) - Radio{0,1} (green)
LAN (connected to PHY)
- GE blue
- FE green
Serial is a Cisco-compatible RJ45 next to the ethernet port.
115200-N-8 are the settings for OS and U-Boot.
Installation
------------
1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in
the root directory of a TFTP server and serve it at
192.168.200.200/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Set the bootcmd so the AP can boot OpenWrt by executing
$ setenv boot_openwrt "setenv bootargs;
cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
$ tftpboot 0x1000000 192.168.200.200:01C8A8C0.img; bootm
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 16b01fb1b9c99513c318109bef96a1a3545c57a0)
The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID.
Thanks to Josh4300 for testing on device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit c642a97aa6b51352a718449cd715b92f94af4a5d)
This allows JCG_MAXSIZE to be specified in kilobytes. This makes
this value more consistent and easier comparable with other size
variables.
This also changes the only occurence of the variable, for Cudy WR1000.
This is backported to 19.07 for convenience, as other developers
backporting device support might not be aware that JCG_MAXSIZE in
kilobytes would not work there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 0bf4d681d4f2e4bd3c3a61e7fe5dca2a40b1902f)
Netgear WNR3500L is an already supported device, but out of the
box, the device has no switch configuration and there is no wan.
The correct configuration for this specific model is similar to
some other models. This simple commit adds the correct switch
and the out-of-the-box experience is improved.
Experimentally determined:
Port 0 => WAN
Port 1..4 => LAN
Port 5..7 => unused
Port 8 => CPU
Signed-off-by: Olli Asikainen <olli.asikainen@gmail.com>
Tested-by: Fabian Zaremba <fabian@youremail.eu>
[added port mapping to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit deb835849aeb713968aaa48bf046101140ab4825)
The Mikrotik RBM33G has only 2 LAN ports.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[moved node in 02_network to maintain alphabetic sorting; backport]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 3a55c7935d4efdc86575601cb4aa7bc94e3c5e44)
Physical port order watched from the backside of the C20i
(from left to right) is: Internet / 1 / 2 / 3 / 4
Physical Port Switch port
WAN 0
LAN 3 1
LAN 4 2
LAN 1 3
LAN 2 4
(not used) 5
CPU 6
Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[commit message/title improvements; backport to 19.07]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a065cd29bf2dfd1ce1f07becd65aef96cec658e7)
The Atheros AR8327 and AR8337 have (according to their datasheet) a
VLAN table with a maximum of 4096 entries.
Currently, there's a hard limit of 128 VLANs, which is the same as
for most other Atheros switches. Increase this limit only for the
AR83x7 series and modify some shared functions to allow them to work
with a variable max VLAN count.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3f79aaa2979793c054eae2c8b4058c8c7fccdbe7)
YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based
(QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE
(802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller
version of the XD4200, with similar specification but lower TX power.
Specification:
- QCA9563 (775 MHz)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN)
- Wi-Fi 2.4 GHz:
- XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA
- A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11)
- Wi-Fi 5 GHz:
- XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11)
- A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11)
- LEDs:
- XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet)
- A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet)
- 1x button (reset)
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x DC jack (12 V)
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit e5d4c0966736287c7ade29c5ccaf6f1ad841b7db)
YunCore QCA9k based devices released in 2019 require a custom TFTP image
for U-Boot built-in recovery mode (triggered with reset button). Image
has to be prepended with 'YUNCORE' keyword followed by U-Boot CLI
commands which will be executed later. Images without the custom header
will be ignored by U-Boot.
To be able to support both the vendor firmware (QSDK) and OpenWrt flash
layouts, used here commands change the 'bootcmd' before flashing image.
This commit adds generic helper script for YunCore devices with 16 MB of
flash and enables TFTP image generation for A770 model.
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[pepe2k@gmail.com: commit description reworded, recipe renamed]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit 8016f648640e8f73f0dc4fc307fb6bebd12afb88)
TP-Link Archer C60 v2 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
Flash instruction (under U-Boot, using UART):
tftp 0x81000000 ...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 974d6958a7c6332438ab4cda98e72156c8d944ed)
TP-Link Archer C60v1 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 ...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6d313da6dc5f655d92aa86e2ec42ecfcf763df3d)
In order to make RSSI indicator on the device work out of box,
include "rssileds" package in per-device rootfs image by default
for Ubiquiti XM and XW devices, namely:
- Bullet M (XM/XW)
- Rocket M (XM/XW)
- Nanostation M (XM/XW)
- Nanostation Loco-M (XW)
This moves the package addition to the individual devices in order
to prevent accidental inclusions of the package when not looking
at the parent node carefully enough.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[add bullet-m-xw, remove rocket-m-ti, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 08d9c95417399ac8615df210f4381cca68a4b25c)
This adds the gpio switch to enable PoE passthrough on Ubiquiti
Nanostation (XM/XW).
Values are copied from the implementation in ar71xx.
GPIO values checked on:
- NanoStation M5 XW
- NanoStation M2 XM
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 317e98a5a2c6f1e2ac599ec530478669b965602c)
Adrian Schmutzler