The first version of this script allowed just 4Mb factory images.
With this patch is possible to set the maximum size of the payload.
For an 8Mb flash, the corresponding maxsize is:
8 * 1024 * 1024 - 5 * 64 * 1024 = 8388608 - 327680 = 8060928
If the -m argument is not set, the default maximum size will be
used for backward compatibility.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
This reverts commit 0111b86f1d as it
breaks on Linux distributions without ed support
./fix-libmath_h: line 1: ed: command not found
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This commit adds the partition layout used by the TP-Link Archer D50
and probably by the TP-Link Archer D7 to mktplinkfw2.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Extended mksenaofw to support new "capwap" header structure.
This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5
firmware.
Note that the factory image format changes for 3.1 and later firmware,
and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the
factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware
will refuse the factory_35.bin file.
Flashing from the Engenius 3.1.0 firmware with the factory_35.bin
firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW")
is only intended as part of the upgrade path to 3.5.5 firmware.
Modified ipq40xx image Makefile to appropriately invoke mksenaofw
with new parameters to configure the capwap header.
Note that there is currently no method to return to factory firmware,
so this is a one-way street.
Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is
to navigate to 192.168.1.1 on the stock firmware and navigate to the
firmware menu. Then copy the URL you have for that page, something like
http://192.168.1.1/cgi-bin/luci/;stok=12345abcdef/admin/system/flashops
and replace the trailing /admin/system/flashops with just /easyflashops
You should then be presented with a simple "Firmware Upgrade" page.
On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox.
Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin,
click "Upgrade" and on the following page select "Proceed".
Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to
use the stock firmware update menu. Choose the
openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click
"Upload" and "Proceed".
The device should then flash the OpenWrt firmware and reboot. Note
that this resets the device to a default configuration with Wi-Fi
disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2
acting as a LAN port with a DHCP server on 192.168.1.x (AP is at
192.168.1.1)
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[sorry, for unfixing the 80-lines eyesores.]
This patch enable gnu99 mode for the nec-enc utility which
fixes the following build-breaking errors on some older
architectures.
nec-enc.c: In function ‘xor_data’:
nec-enc.c:34:2: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < len; i++) {
^~~
nec-enc.c:34:2: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 to compile your code
nec-enc.c: In function ‘main’:
nec-enc.c:101:3: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < n; i++) {
^~~
Spotted-By: Buildbot
Fixes: fac27643f0 ("firmware-utils: add nec-enc")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
nec-enc provides firmware encoding/decoding with model specific key
for NEC devices.
known devices:
- Aterm WF1200CR
- Aterm WG1200CR
- Aterm WG2600HS
usage:
nec-enc -i infile -o outfile -k key
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[checkpatch fixes, marked usage as noreturn, added static function,
moved buf* from stack to the global data segment]
I made a similar change to this here:
https://github.com/openwrt/packages/pull/8159
However, it turns out this did not fix the problem as the problem has to
do with tools/xz and not the xz package. The error is the same and causes
linking errors as can be seen above.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This provides board configuraion tables for various Tegra boards needed
by cbootimage tool to create flashable bootloader images.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tegra BCT and bootable flash image generator/compiler
>From documentation:
This project provides a tool which compiles BCT (Boot Configuration
Table) images to place into the boot flash of a Tegra-based device.
The tool will either:
a) Compile a textual representation of a BCT into a binary image.
b) Generate an entire boot image from a previously compiled BCT and a
bootloader binary.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Specifications:
* SoC: Qualcomm Atheros QCA9533 (650MHz)
* RAM: 64MB
* Storage: 8 MB SPI NOR
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI or TFTP
To get to TFTP recovery just hold reset button while powering
on for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Thanks to robimarko for the work inside the ar71xx tree.
Thanks to adrianschmutzler for deep discussion and fixes.
Signed-off-by: Mario Schroen <m.schroen@web.de>
[Split into DTS/DTSI, read-only config partition in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename, light subject touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is also helpful to add support in ath79.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Some boards with JBOOT have partiton between bootloader
and kernel image. This patch add possibility to change kernel
partition start address.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The cmake bump to 3.14.0 breaks build on all targets. Revert it for now.
This reverts commit a3446257a8.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update CMake to 3.14.0
Refresh patches
Remove inofficial fossies.org and replace with GitHub (link on official site)
Remote 150-C-feature-checks-Match-warnings-more-strictly.patch as it's
a no longer needed backport from upstream.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range
extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros
QCA9558 + QCA9882 + AR8035 platform and is available only on US market.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x 1 Gbps Ethernet (AR8035)
- 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11)
- 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11)
- 2x U.FL connector on PCB
- 2x dual-band PCB antennas
- 1x LED, 2x dual-color LED (all driven by GPIO)
- 3x button (app config, led, reset)
- 1x mechanical on/off slide switch
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x JTAG (8-pin, 1.27 mm pitch) header on PCB
Flash instruction:
Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254,
default credentials: admin/admin).
Warning:
This device does not include any kind of recovery mechanism in U-Boot.
Vendor firmware access:
You can access vendor firmware over serial (RX line requires jumper
resistor in R306 place, near XTAL) with: root/sohoadmin credentials.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Require the word "warning" to appear at the start of a line, after
whitespace, or after a `:`. This is the same that CTest launchers use
to match warnings. It avoids matching "warning" inside file paths.
Fixed in cmake 3.14.0.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Fixes timeouts with trying to access the FTP site.
Also remove mirror2.openwrt.org, which does not keep current tarballs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
gnu date is present in our staging_dir which means squashfskit will fail
to build. Prevent also a race condition if coreutils is build after
squashfskit.
To prevent a race condition, depend on coreutils.
Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
squashfskit is a fork of the squashfs-tools.
squashfskit creates reproducible filesystems and includes
many of the distro patches.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Paul Spooren <mail@aparcar.org>
This makes OpenWrt build an Ext2+Ext4 partitioned image
for the D-Link DNS-313 with two blank partitions, a boot
partition on /dev/sda3 and a rootfs partition on
/dev/sda4.
This uses the methods already used in apm821xx including
the tricks to convert the generated Ext2 filesystem
partition to version 1 so that the firmware bootloader
will properly recognize it.
We patch a bit around the build files to make sure we
get the rootfs size set and that genext2fs is properly
built.
Tested on the D-Link DNS-313.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Fixing and tricksing]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The firmware on the D-Link DNS-313 NAS require two blank
partitions before the boot partition. Support this if
explicitly requested with a "-n" flag.
Tested on the D-Link DNS-313.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Broken out from original patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update mpfr to 4.0.2
Use official site as last resort
Force thread-safety functionality
Refresh patches
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Fix for factory image generation, so that stock firmware will accept the
openwrt image.
Ref: https://forum.openwrt.org/t/support-for-tp-link-archer-c2-v3/15617/17
Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt>
[reword commit message, use correct order for conditions,
trim trailing whitespace]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality
Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.
Use a fixed timestamp within the zip archive to make the images
reproducible.
Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.
Beside all changes, the footer still looks wrong in compare to the
netgear update image.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the option -mt/--mtime to pass a timestamp which is used as filedate
for the containing files.
So far, it isn't used for anything written to the extra fields,
therefore requires the -X (eXclude eXtra file attributes) parameter to
be effective.
Signed-off-by: Mathias Kresin <dev@kresin.me>
One image requires a zip compressed image, so add the zip util found in
the packages feed, and extend it with some useful debian patches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
While we don't need the gnu99 option anymore, we still need to force the
c99 standard to fix the following build error on the build bots:
src/mkdlinkfw.c: In function 'find_auh_headers':
src/mkdlinkfw.c:267:3: error: 'for' loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < header_counter; i++) {
^
src/mkdlinkfw.c:267:3: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 to compile your code
Signed-off-by: Mathias Kresin <dev@kresin.me>
fread() doesn't set errno, ferror need to be used to check for errors.
While at it, check if we read the expect number of elements.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the SOURCE_DATE_EPOCH environment variable if set instead of the
current time. The used timestamp matches the timestamp of the latest
commit this way and make the images reproducible.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop unused function and macros. With the cleanup the gnu extension
typeof isn't used any longer and the gnu99 compile flag can be dropped.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Davide Fioravanti