* wg-quick: freebsd: allow loopback to work
FreeBSD adds a route for point-to-point destination addresses. We don't
really want to specify any destination address, but unfortunately we
have to. Before we tried to cheat by giving our own address as the
destination, but this had the unfortunate effect of preventing
loopback from working on our local ip address. We work around this with
yet another kludge: we set the destination address to 127.0.0.1. Since
127.0.0.1 is already assigned to an interface, this has the same effect
of not specifying a destination address, and therefore we accomplish the
intended behavior. Note that the bad behavior is still present in Darwin,
where such workaround does not exist.
* tools: remove unused check phony declaration
* highlighter: when subtracting char, cast to unsigned
* chacha20: name enums
* tools: fight compiler slightly harder
* tools: c_acc doesn't need to be initialized
* queueing: more reasonable allocator function convention
Usual nits.
* systemd: wg-quick should depend on nss-lookup.target
Since wg-quick(8) calls wg(8) which does hostname lookups, we should
probably only run this after we're allowed to look up hostnames.
* compat: backport ALIGN_DOWN
* noise: whiten the nanoseconds portion of the timestamp
This mitigates unrelated sidechannel attacks that think they can turn
WireGuard into a useful time oracle.
* hashtables: decouple hashtable allocations from the main device allocation
The hashtable allocations are quite large, and cause the device allocation in
the net framework to stall sometimes while it tries to find a contiguous
region that can fit the device struct. To fix the allocation stalls, decouple
the hashtable allocations from the device allocation and allocate the
hashtables with kvmalloc's implicit __GFP_NORETRY so that the allocations fall
back to vmalloc with little resistance.
* chacha20poly1305: permit unaligned strides on certain platforms
The map allocations required to fix this are mostly slower than unaligned
paths.
* noise: store clamped key instead of raw key
This causes `wg show` to now show the right thing. Useful for doing
comparisons.
* compat: ipv6_stub is sometimes null
On ancient kernels, ipv6_stub is sometimes null in cases where IPv6 has
been disabled with a command line flag or other failures.
* Makefile: don't duplicate code in install and modules-install
* Makefile: make the depmod path configurable
* queueing: net-next has changed signature of skb_probe_transport_header
A 5.1 change. This could change again, but for now it allows us to keep this
snapshot aligned with our upstream submissions.
* netlink: don't remove allowed ips for new peers
* peer: only synchronize_rcu_bh and traverse trie once when removing all peers
* allowedips: maintain per-peer list of allowedips
This is a rather big and important change that makes it much much faster to do
operations involving thousands of peers. Batch peer/allowedip addition and
clearing is several orders of magnitude faster now.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This is bugfix release that incorporated all of the devcrypto engine
patches currently in the tree.
The cleaning procedure in Package/Configure was not removing the
dependency files, causing linking errors during a rebuild with
different options. It was replaced by a simple make clean.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
omcproxy's configuration is lost on every update or installation.
Avoid it by defining the configuration file.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
After update to 5.0.1 iw-full package failed to display command list on
ipq40xx arch. Root cause was found to be LTO reordering causing
incorrect detection of command struct size in:
iw.c:552
cmd_size = labs((long)&__section_set - (long)&__section_get);
This reverts commit ef16a394d2.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This can break for example 5GHz meshpoint interfaces
because 0 maps to a CCK rate (11Mbit/s).
It must also be avoided that the ath10k-ct internal state for the rates is
not synced with the mac80211 rates state. Otherwise, the user specified
rate (e.g. a wifi-iface mcast_rate for a meshpoint interface) will only be
set on startup. And a short while after that, ath10k-ct specific code in
ath10k_check_apply_special_rates is missing a valid rate in its own
structures and is then recalculating a new default rate. This default rate
is in most situations not the requested rate.
Fixes: 4df3c71cd4 ("ath10k-ct: Update to 2018-12-11 and use version based on 4.19")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This breaks for example 5GHz meshpoint interfaces because
0 maps to a CCK rate (11Mbit/s).
Fixes: db90c243a0 ("mac80211: update to version based on 4.19-rc4")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This should fix the WDS / 4addr mode with ath10k and probably other
devices.
This patch was found here: https://patchwork.kernel.org/patch/10692383/
Fixes: d9eefa7a70 ("mac80211: rebase ontop of v4.18.5")
Reported-by: Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix crash due to passing invalid r2x00dev->eeprom_file pointer to
release_firmware(). Since we copy eeprom data with EEPROM_SIZE
in rt2800_read_eeprom() we can use eeprom_file->size as marker
if the file was crated by request_firmware().
Acked-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
On targets that don't have input support enabled in the kernel config,
building kmod-input-touchscreen-ads7846 fails due to a missing
dependency on kmod-input-core. Add the dependency to fix this.
Fixes: 77a54bbf13 ("kernel: add kmod-input-touchscreen-ads7846")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
max_ttl - limit the ttl in the dns answer if greater as $max_ttl
min_cache_ttl - force caching of dns answers even the ttl in the answer
is lower than the $min_cache_ttl
max_cache_ttl - cache only dns answer for $max_cache_ttl.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This module adds support for ADS7846 based touchscreens used in devices
like the WaveShare 3.5" and 4" LCD displays designed for Raspberry Pi.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This module adds support for the ILI9486 LCD controller used in devices
like the Waveshare 3.5" and 4" LCD displays designed for Raspberry Pi.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This module adds support for small TFT LCD display modules. While this
module also exists in the 4.9 kernel, we are not going to support this
kernel in the next major release, so don't make it available for 4.9.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The kernel modules that provide support for framebuffers in system RAM
are currently included in the kmod-drm-imx package. Move them to a
separate package, so that other modules can depend on them.
Increase the autoload order of the drm-imx* packages to load the modules
after loading the fb modules they depend on.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This makes it clear that localuse when explicitly specified in the
config will have its final say on whether or not the initscript should
touch /etc/resolv.conf, no matter whatever the result of previous
guesswork would be
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This commit updates the file "board-linksys_ea6359v3".
Without this commit, the Linksys EA6350v3 will experience poor wireless
performance in both bands. With this patch, wireless performace will be
comparable to the performance of the stock firmware.
Signed-off-by: Oever González <notengobattery@gmail.com>
The board-files are specific to the target and device. Hence
they need to be set as nonshared. Otherwise they do not show
up on the package repository. This causes problems for
imagebuilder, if it needs to build a image for a specific
device that hasn't had the time to have get its boardfile
upstream.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Apparently this modem replies differently to attempted --get-pin-status
which makes the script fail if a pincode is set. Fix this.
Manufacturer: Sierra Wireless, Incorporated
Model: MC7455
Revision: SWI9X30C_02.24.05.06 r7040 CARMD-EV-FRMWR2 2017/05/19 06:23:09
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Cherry-pick Multi-AP commits from uptream:
9c06f0f6a hostapd: Add Multi-AP protocol support
5abc7823b wpa_supplicant: Add Multi-AP backhaul STA support
a1debd338 tests: Refactor test_multi_ap
bfcdac1c8 Multi-AP: Don't reject backhaul STA on fronthaul BSS
cb3c156e7 tests: Update multi_ap_fronthaul_on_ap to match implementation
56a2d788f WPS: Add multi_ap_subelem to wps_build_wfa_ext()
83ebf5586 wpa_supplicant: Support Multi-AP backhaul STA onboarding with WPS
66819b07b hostapd: Support Multi-AP backhaul STA onboarding with WPS
8682f384c hostapd: Add README-MULTI-AP
b1daf498a tests: Multi-AP WPS provisioning
Add support for Multi-AP to the UCI configuration. Every wifi-iface gets
an option 'multi_ap'. For APs, its value can be 0 (multi-AP support
disabled), 1 (backhaul AP), 2 (fronthaul AP), or 3 (fronthaul + backhaul
AP). For STAs, it can be 0 (not a backhaul STA) or 1 (backhaul STA, can
only associate with backhaul AP).
Also add new optional parameter to wps_start ubus call of
wpa_supplicant to indicate that a Multi-AP backhaul link is required.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Those have by now been merged into wireless-drivers-next:
17ae2acd1a6f rt2x00: remove unneeded check
5991a2ecd070 rt2x00: remove confusing AGC register
9ad3b5565445 rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band
7aca14885ede rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620
c7ff1bfeaf1c rt2800: comment and simplify AGC init for RT6352
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently these kernel packages only work on x86, restrict them to that
target.
Fixes: 2f239c02a0 ("x86: video: add amdgpu DRM kernel package")
Fixes: 2f6918ee9b ("x86: video: add radeon DRM module support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit e6d84fa886 as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This reverts commit 26681fa6a6 as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This reverts commit fc80ef3613 as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and
rdma for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This reverts commit 248797834b as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Currently it seems impossible to configure /etc/config/dhcp to achieve
the following use case
- run dnsmasq with no-resolv
- re-generate /etc/resolv.conf with "nameserver 127.0.0.1"
Before this change, we have to set resolvfile to /tmp/resolv.conf.auto
to achive the 2nd effect above, but setting resolvfile requires noresolv
being false.
A new boolean option "localuse" is added to indicate that we intend to
use dnsmasq as the local dns resolver. It's false by default and to
align with old behaviour it will be true automatically if resolvfile is
set to /tmp/resolv.conf.auto
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
backport from wireless-drivers-next, replacing some existing patches in
our tree (marked with '=' are those which were already present):
f483039cf51a rt2x00: use simple_read_from_buffer()
=5c656c71b1bf rt2800: move usb specific txdone/txstatus routines to rt2800lib
=0b0d556e0ebb rt2800mmio: use txdone/txstatus routines from lib
=5022efb50f62 rt2x00: do not check for txstatus timeout every time on tasklet
=adf26a356f13 rt2x00: use different txstatus timeouts when flushing
=0240564430c0 rt2800: flush and txstatus rework for rt2800mmio
6eba8fd22352 rt2x00: rt2400pci: mark expected switch fall-through
10bb92217747 rt2x00: rt2500pci: mark expected switch fall-through
916e6bbcfcff rt2x00: rt2800lib: mark expected switch fall-throughs
641dd8068ecb rt2x00: rt61pci: mark expected switch fall-through
750afb08ca71 cross-tree: phase out dma_zalloc_coherent()
=c2e28ef7711f rt2x00: reduce tx power to nominal level on RT6352
a4296994eb80 rt2x00: Work around a firmware bug with shared keys
2587791d5758 rt2x00: no need to check return value of debugfs_create functions
pending on linux-wireless:
rt2x00: remove unneeded check
rt2x00: remove confusing AGC register
rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band
rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620
rt2800: comment and simplify AGC init for RT6352
rt2x00: do not print error when queue is full
rt2800: partially restore old mmio txstatus behaviour
rt2800: new flush implementation for SoC devices
rt2800: move txstatus pending routine
rt2800mmio: fetch tx status changes
rt2800mmio: use timer and work for handling tx statuses timeouts
rt2x00: remove last_nostatus_check
rt2x00: remove not used entry field
rt2x00mmio: remove legacy comment
While at it also rename some existing patches now that there are
separate folders with patches for each driver to make things a bit
nicer to handle.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This applies to kernel 4.10 and newer.
See 8db4c5be88
The above commit added to kernel 4.10 added new dependency
for building the NETFILTER_XT_MATCH_SOCKET (xt_socket.ko)
module. The NF_SOCKET_IPVx options (both of them) need to
be enabled in order to build the NETFILTER_XT_MATCH_SOCKET
module. Without the change the module is not built.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
These two dependencies are mutual exclusive and it is only possible to
select one of them, change the select to a chose so it is only possible
to select one of them in OpenWrt menu config.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Jason A. Donenfeld