Register buttons and leds through DT for all available dts,
and remove them from the board files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: remove leds/buttons from board files
fix wrong led polarities for dsl-274xb-c2, cpva642, p870hw
comment out spi-gpio and associated leds]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44566
Move compatible strings from board structs into separate table. This
allows for several board compatibles to match to the same board in case
e.g. only the flash size / partitions differ.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43341
This changes board info to match the Wiki
http://wiki.openwrt.org/toh/huawei/hg556a, removes the no longer needed
fallback board and fixes HG556 Ralink eeprom extraction.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: rename partitions instead]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42206
Now that we migrated all users to dtb based detection, we can drop the
board fixup code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42129
This requires individual images for each board version for now.
Linux partition was shrunk to ensure writing thewrong image won't
erase wifi calibration data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42126
Allow appending a dtb blob to the binary and use it for identifying the
board. Fall back to nvram based identification in case of no dtb passed.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42119
Rework fallback sprom support by providing different sproms for
different chips. Also make it optional to use.
This likely causes sprom fallback support to break on a few boards.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41942
- adsl and lan leds are swapped.
- internetkey is labeled as hspa.
- enable status led and reset button for failsafe.
- use new leds script.
- fix switch configuration.
- remove enet0 from board_info.
- add profile.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41588
Move defines and board_info structs back to their proper locations so
(de-)selecting SOC support won't break the build.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41550
Some fixes for Telsey CPVA502+ bcm6348 routers:
- reset the external PHY (eth1) with proper platform code, not using a led definiton
- eth1 is an external phy, not a switch, deleted forced link speed
- fixed led color
Patch made for 3.14 kernel patches.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: also fix 3.14, refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41420
Use the CFE_EPTSEAL to tell them apart at runtime. Added for now only
for the 3.14 until properly tested.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41296
Now that 3.13 will be EOL soon, switch to 3.14.
Known issues:
* 74x164 is not available because upstream dropped non-DT support
* jffs2 breaks with SMP
Unknown issues:
* probably plenty
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 40380
Add support for 3.13 as a development kernel. Mostly untested, only net
booted. If flashed may brick your router or kill your cat.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39746
Jonas Gorski