To make the lzma-loader build with binutils 2.25.1 it is needed to
remove the .MIPS.abiflags section otherwise I get the following compile
error:
mips-openwrt-linux-musl-objcopy -O binary -R .reginfo -R .note -R .comment -R .mdebug -S loader loader.bin
mips-openwrt-linux-musl-objcopy: Warning: Writing section `.text' to huge (ie negative) file offset 0xffffffff80a00000.
mips-openwrt-linux-musl-objcopy:loader.bin[.text]: File truncated
This should close#20487.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46893
This moves arch patches affecting many DTS files. Thanks to this change
we can put some ready-to-mainline patches at 300-319 and simplify
backporting process.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46889
As requested here #20432 I've
tried to fix the missing symbols from the specified default kernel
config files.
I ran into this problem trying to build an image for x86_64 target
with a custom kernel configuration.
Signed-off-by: Manganini Mirko <mmanganini@gmail.com>
SVN-Revision: 46879
the trx utile uses a maximum image size of 7.2MB. There are brcm47xx
devices even with serial flash with bigger flash chips, but OpenWrt was
not able to create images for these devices. This patch provides an
additional parameter which increases this limit to 32 MB. There is a
warning in the trx utile code which suggests that bigger images could
overwrite the nvram partition on some devices, but normally the program
writing the image should make sure that it is safe to write it to the
flash.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46872
This patch changes nothing on the behaviour, it just breaks long lines
with bin/trx to make it easier to add additional parameters.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46871
Fixes support for AR9287 on TP-Link TD-W8980 and possibly other devices
which have an ath wifi chip at a PCI address other than 0xb8000000
(TD-W8980 for example has it's wifi chip at 0xbc000000).
Signed-off-by: Geoffrey McRae <geoff@spacevs.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46869
The previous "link" and "status" functions were non-standard,
and thus less useful for parsing.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 46864
Increase space for kernel and also introduce a 8M flash target into the
Makefile.
Signed-off-by: Attila Lendvai <attila@lendvai.name>
SVN-Revision: 46862
The PBR-M1 and other upcoming MT7621 boards have RTC chips on them. The
PBR-M1 also selects the kmod-rtc-pcf8563 by default. But the module itself
will not be build because CONFIG_RTC_CLASS is currently not enabled for its
kernel.
Enabling this option should fix the problem of the missing rtc device on
these boards.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46857
According to the AR7242 datasheet section 2.8, AR724X CPUs use a 40MHz
input clock as the REF_CLK instead of 5MHz.
The correct CPU PLL calculation procedure is as follows:
CPU_PLL = (DIV * REF_CLK) / REF_DIV / 2.
This patch is compatible with the current calculation procedure with default
DIV and REF_DIV values.
Test on both AR7240, AR7241 and AR7242.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46856
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 46852
In krait_cpufreq_probe, both freq and max_cpu_freq are never
initialized, so the max_cpu_freq will have a random value at the end.
Fix this by properly initializing max_cpu_freq to 0 and storing the clk
frequency in freq as well, to make it similar to how it's calculated in
krait_set_target.
Fixes the following warnings:
In file included from include/linux/clk.h:16:0,
from drivers/cpufreq/cpufreq-krait.c:13:
drivers/cpufreq/cpufreq-krait.c: In function 'krait_cpufreq_probe':
include/linux/kernel.h:714:24: warning: 'freq' may be used uninitialized in this function [-Wmaybe-uninitialized]
_max1 > _max2 ? _max1 : _max2; })
^
drivers/cpufreq/cpufreq-krait.c:217:25: note: 'freq' was declared here
unsigned long freq_Hz, freq, max_cpu_freq;
^
In file included from include/linux/clk.h:16:0,
from drivers/cpufreq/cpufreq-krait.c:13:
include/linux/kernel.h:714:24: warning: 'max_cpu_freq' may be used uninitialized in this function [-Wmaybe-uninitialized]
_max1 > _max2 ? _max1 : _max2; })
^
drivers/cpufreq/cpufreq-krait.c:217:31: note: 'max_cpu_freq' was declared here
unsigned long freq_Hz, freq, max_cpu_freq;
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46839
The phy driver has its qcom-dwc3 order switched in contrast to the usb
controller driver.
Signed-off-by: Kaspar Schleiser <kaspar@schleiser.de>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46838
commit r30917 ("kernel: bypass all netfilter hooks if the sysctls for that
functionality have been disabled - eliminates the overhead of enabling
CONFIG_BRIDGE_NETFILTER in the kernel config") introduced an optimization
which should reduce/eliminate the overhead for traffic send over bridges on
kernels compiled with CONFIG_BRIDGE_NETFILTER=y. But this optimization
breaks the nf_call_iptables per bridge setting which is more fine grained
than the global sysctl net.bridge.bridge-nf-call-iptables setting.
A test reflecting a real world setup was created to identify if this really
eliminates the overhead and if per-bridge nf_call_iptables could be used in
some setups to increase the throughput. A Qualcomm Atheros QCA9558 based
system with one ethernet and an ath9k wifi 3x3 in HT40 mode was used.
Cables from the AP to the wifi station were used to reduce interference
problems during the tests.
The wlan interface was put in one bridge interface called br-wlan. This
bridge usually contains some more wlan interfaces. The eth0 was put in a
second bridge called br-lan. This usually contains some other privileged
wlan or mesh interfaces. Routing was added between br-lan and br-wlan.
Three kernels were tested:
* (default) OpenWrt kernel for this device
* (brfilter-global) OpenWrt kernel with CONFIG_BRIDGE_NETFILTER=y
* (brfilter-local) OpenWrt kernel with CONFIG_BRIDGE_NETFILTER=y and
without 644-bridge_optimize_netfilter_hooks.patch
The changes to the the netfilter settings of the bridge were done via:
* (brfilter-global) /sbin/sysctl -w net.bridge.bridge-nf-call-iptables=1
* (brfilter-lobal) echo 1 > /sys/class/net/br-lan/bridge/nf_call_iptables
and/or echo 1 > /sys/class/net/br-wan/bridge/nf_call_iptables
A station connected to the wlan0 (AP) interface was used to send traffic to
a PC connected via ethernet. iperf with 3 concurrent transmissions was used
to generate the traffic.
| kernel | br-nf-* global | nf-call* iface | download | upload |
|-----------------|----------------|----------------|----------|----------|
| default | 0 | - | 209 | 268 |
| brfilter-global | 0 | - | 185 | 243 |
| brfilter-local | 0 | - | 187 | 243 |
| brfilter-local | 0 | br-lan | 157 | 226 |
| brfilter-local | 0 | br-lan br-wlan | 139 | 161 |
| brfilter-global | 1 | - | 136 | 162 |
Download/upload results in Mibit/s
It can be seen that the patch doesn't eliminate the overhead. It can also
be seen that the throughput of brfilter-global and brfilter-local with
disabled filtering is the roughly the same. Also the throughput for
brfilter-global and brfilter-local for enabled filtering on all bridges is
roughly the same.
But also the brfilter-local throughput is higher when only br-lan requires
the filtering. This setting would not be possible with
644-bridge_optimize_netfilter_hooks.patch applied and thus can only be
compared with brfilter-global and filtering enabled for all interfaces.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46835
It was corrupted in r38528. The most obvious symptom is repeated messages like this:
Tue Sep 8 08:25:18 2015 kern.warn kernel: [77141.972226] br-lan: received packet on wlan0 with own address as source address
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
SVN-Revision: 46821
Everything except for blkcipher was already built-in, so make blkcipher
built-in as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46820
Add support for the Netgear Nighthawk X4 R7500 and build
appropariate sysupgrade and factory images.
Known issues:
* 5 GHz wifi not working - there is no quantenna driver
* One of the USB ports is not working
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46796
To use gpio leds as ide leds, we need to enable the trigger to be
included in the kernel.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46795
Add full ubi and sysupgrade images for AP148 and add sysupgrade support
for ipq806x to allow updating the current installation.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46789
Felix Fietkau