Let DHCP client send a release when it exists so the DHCP server is
informed the IP address is released and allowing to clean up IP/mac
state info in intermediate devices.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Update to latest HEAD in order to remove the faulty "prelocal" ip rule leading
to unexpected policy rule precedence.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
I do not know if this causes any problems now, but we should not set
it, because it is reserved. Some more recent versions of the Lantiq DSL
API driver and Control is checking if only valid bits are set.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48948
There are some cases where ISPs are running ATM over VDSL or PTM over
ADSL, this is not the common case, but these cases exist. Make it
possible to configure OpenWrt for such cases by adding a new config
option line_mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48947
The detailed annex option were only available in the danube DSL app
including the activation of G.992.2 Annex A (ADSL Lite). This is now
also added to the vdsl app for the vrx200.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48946
The adsl control app missed the activation of annex M and annex L in
the Annex A part, this now activates everything the firmware supports.
In Annex L type only the wide US (Mask1) was activated, now also the
narrow US (Mask2) version gets activated.
In addition annex J was also added.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48945
I am not calling dsl_cmd because I want to ignore the lock, quit
should also be send when someone else is accessing it. I saw that some
other call was stuck here and all following calls were stuck in the
dsl_cmd lock.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48943
Ensure that ikey and okey are sent in network byte order to the kernel.
Also don't mangle external IP addrs and routes when reconfiguring iinterfaces.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 48919
Before r47933 Bit 1 (first bit) of xTSE Octet 1 (first octet) defaulted
to 1, which allowed T1.413 to operate.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
SVN-Revision: 48763
Supported syntax is inspired by ethtool. Example usages:
swconfig dev switch0 port 2 set link "duplex half speed 100"
swconfig dev switch0 port 2 set link "autoneg on"
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48624
UCI paramater multicast is added which allows to toggle multicast support on gre interfaces.
By default multicast support is enabled as gre tunnels are often used in combination with
routing protocols using multicast.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Nick Podolak <nicholas.podolak@dtechlabs.com>
SVN-Revision: 48596
* Enable drop_invalid by default to catch unnatted packets (#21738)
* Fix processing of inversions for -i, -o, -s, -d and -p flags
* Remove delegate_* chain indirection but rely on xt_id to identify own rules
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 48551
This adds IPv6 support to qos-scripts for both tc/qdisc and the
iptables classification rules. The tc/qdisc part is accomplished
by removing "protocol ip" from the tc command line, causing the
rule to be applied to all protocols. The iptables part is
accomplished by adding each rule using both iptables and ip6tables.
This patch is based on previous work by Ilkka Ollakka and
Dominique Martinet.
Signed-off-by: Michael Marley <michael@michaelmarley.com>
SVN-Revision: 48452
This adds a "srciface" option that can be used on classification
rules in /etc/config/qos. This is useful to allow prioritization
based on the local network from which the traffic originates, for
example to deprioritize traffic from a guest network.
Signed-off-by: Michael Marley <michael@michaelmarley.com>
SVN-Revision: 48446
Set the save-mark mask for the qos_${cg} chain to 0xff instead of
0xf0. With the old value, the nibble that was saved would be
masked during the restore, preventing ingress traffic from being
classified. Thanks to nbd for recommending the fix.
Signed-off-by: Michael Marley <michael@michaelmarley.com>
SVN-Revision: 48388
This adds support for configuring VTI interfaces within /etc/config/network.
VTI interfaces are used to create IPsec tunnel interfaces. These interfaces
may be used for routing and other purposes.
Example config:
config interface 'vti1'
option proto 'vti'
option mtu '1500'
option tunlink 'wan'
option peeraddr '192.168.5.16'
option zone 'VPN'
option ikey 2
option okey 2
config interface 'vti1_static'
option proto 'static'
option ifname '@vti1'
option ipaddr '192.168.7.2/24'
The options ikey and okey correspond to the fwmark value of a ipsec policy.
The may be null if you do not want fwmarks.
Also peeraddr may be 0.0.0 if you want all ESP packets go through the
interface.
Example strongswan config:
conn vti
left=%any
leftcert=peer2.test.der
leftid=@peer2.test
right=192.168.5.16
rightid=@peer3.test
leftsubnet=0.0.0.0/0
rightsubnet=0.0.0.0/0
mark=2
auto=route
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 48274
Source package gre was depending on kmod-ip6-gre, however the actual
kernel module package that is created is kmod-gre6. Therefore
update (source) package gre for ipv6 gre support.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 48100
Add back a slightly modified version of the lowlevel settings which
where removed with r46920.
In compare to the old lowlevel settings, the B43c tone is added to
tone_adsl_b and tone_adsl_bv.
If an unsupported tone value is used, the auto probing mode is used, in
compare to the fallback to tone_adsl_av and tone_vdsl_av with the old
lowlevel settings.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48054
According to ITU-T G.997.1 Amendment 2 (04/2013) section 2.1, bit 3 of
XTSE octet 8 either allow or denies the initialization of G.993.5.
Even if the current redistributable xDSL firmware doesn't include
G.993.5 vectoring support, enable this bit by default to allow people to
get their G.993.5 line working using a custom xDSL firmware.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48053
r47933 revealed that the driver/app in combination with the chosen
firmware does a good job in selecting a working xtse.
Use this probing mode if no annex is specified.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48052
This patch adds the missing VDSL2 bits to the annex specific XTSE (like
it should be according to the comments above the XTSE bits).
Since r47933 it's mandatory to remove the annex option to switch to
VDSL2 (only) operation mode.
As shown by ticket #21436 and a few mails I received personally, even
experienced users are not aware that they have to remove the annex
option to get their VDSL2 line working and as shown by this patch it
doesn't need to be that "complicated".
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48051
When using cli, print link state the same way kernel used to do it.
This will allow kernel switching PORT_LINK from SWITCH_TYPE_STRING.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47998
- CONFIG_IFX_CLI is unused, couldn't find any reference to this config variable
- use disable-feature instead of enable-feature=no
- reorder configure args to have depending args together
- remove configure args which set the default value
- group enable-model and configure args which enable or disable features that
are covered by the feature set
The config.log contains the same values as before. The vdsl_cpe_control binary
has the same checksum as before.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47888
The typicial feature set doesn't include "DSL PM showtime counters support"
(INCLUDE_DSL_CPE_PM_SHOWTIME_COUNTERS). This feature provides the
vdsl_cpe_control command 'pmccsg', which is used by 'dsl_control status' to get
the line uptime.
The binary size increases to 103912 byte (+4256 byte) uncompressed.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47887
this error was not visible until recent bump to
busybox 1.24.1 stable which introduced a warning message
when keyword 'local' is not used with a shell-function.
this does not change behavior and is a cosmetic cleanup.
fixes the following output:
root@box:~ ifup <interface>
/sbin/ifup: local: line 362: not in a function
/sbin/ifup: local: line 362: not in a function
/sbin/ifup: local: line 1: not in a function
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 47828
Use the 'typical' compile configuration instead of 'full', which most
notably excludes the soap support.
/sbin/vdsl_cpe_control shrinks down to ~50%, from 178kb(!) to 90kb.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47769
In this upstream dsl driver app version the autoboot is deactivated activate
it again.
In addition to the update this also fixes some build warnings and makes it
use the same configure option as used in Lantiq UGW.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47637
Hans Dedecker