Modify the title to match the following format, as it's enough
to uniquely identify a device:
<manufacturer> <model>
This matches what's done for other targets and has the
added benefit of creating a sorted-by-manufacturer list
of devices on menuconfig
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the
following specifications:
- MT7620A (580 MHz)
- 128MB RAM
- 32MB of flash (SPI NOR)
- 5x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus)
- 2x SIM card slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 10x LEDs (4 GPIO-controlled)
- 1x reset button
The following have been tested and working:
- Ethernet switch
- wifi
- miniPCIe slot
- USB port
- microSD slot
- sysupgrade
- reset button
Installation and recovery:
In order to install OpenWRT the first time or recover the router, you
can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address. Upload the firmware to start the recovery
process.
How to swap SIMs:
You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio13/value. In order for the change to take effect,
you can either use AT-commands (AT+CFUN) or power-cycle the modem (write
0/1 to /sys/class/gpio/gpio14/value).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed
specifications are:
- MT7620A (580MHz)
- 64MB RAM
- 16MB of flash (SPI NOR)
- 6x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM
SIM7100E LTE modem.
- 2x SIM slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 1x 5GHz wifi (mt7612)
- 1x reset button
- 1x WPS button
- 3x GPIO-controllable LEDs
- 1x 10 pin terminal block (RS232, RS485, 4 x GPIO)
Tested:
- Ethernet switch
- Wifi
- USB slot
- SD card slot
- miniPCIe-slot
- sysupgrade
- reset button
Installation instructions:
Installing OpenWRT for the first time requires a bit of work, as the
board does not ship with OpenWRT. In addition, the bootloader
automatically reboots when installing an image over tftp. In order to
install OpenWRT on the HDRM200, you need to do the following:
* Copy the initramfs-image to your tftp-root (default filename is
test.bin) and configure networking accordingly (default server IP is
10.10.10.3, client 10.10.10.123). Start your tftp server.
* Open the board and connect to UART. The pins are exposed and clearly
marked.
* Boot the board and press 1.
* Either use the default filename and client/server IP-addresses, or
specify your own.
The image should now be loaded to memory and board boot. If the router
reboots while the image is loading, you need to try again. Once the
board has booted, copy the sysupgrade-image to the router and run
sysupgrade in order to install OpenWRT to the flash.
Notes:
- You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio0/value. In order for the change to take
effect, you can either use AT-commands (AT+CFUN) or power-cycle the
modem (write 0/1 to /sys/class/gpio/gpio21/value).
- RS485 is available on /dev/ttyS0.
- RS232 is available on /dev/ttyS1.
- The name of the ioX-gpios map to the labels on the casing.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[fixed whitespace issue and merge conflict in target.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These dts itself are incomplete (e.g. missing mtd partitions) and its
deivce support is never added to ath79 target.
Drop these unused dts for now.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
In commit e9652e1696 ("ath79: fix pinmux for ar933x devices") I've
wrongly changed desired register value to 0xf8 although it should've
been set to 0x0.
0xf8 value sets bits 3-7 (ETH_SWITCH_LEDx_EN) to 1 which actually
enables ethernet switch LEDs, so 0x0 is correct value in order to use
the pins as GPIO.
Fixes: e9652e1696 ("ath79: fix pinmux for ar933x devices")
Reported-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Simply dumped content of this regs in ar71xx and wrote them to DTS, as a
result port 6 on the switch will appear disconnected as on Archer C7v4.
[AS: testing and PORT6_STATUS fix]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Properly disable the SoC's internal Switch LEDs on the pinmux.
Devices that previously called ath79_gpio_function_disable for
the switch LEDs, just need to reference switch_led_pins in the
pinctrl-0 property of the gpio-leds node.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[changed desired pinctrl register value from 0x1f to proper 0xf8]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[renamed pinmux name to switch_led_disable_pins to make purpose more clear]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This devices have LEDs connected to the SoC's GPIOs, so it makes no
sense to fiddle with ar8327 LED regs.
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Network for the Archer C25 v1 is set up without switch for no
obvious reason. The LED setup is even done switch-based.
This patch changes network setup so a switch is created.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
for better identification. Also create SUPPORTED_DEVICES string from it
which corresponds to dts compatible string.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The driver is for the I2C mux.
Schematic available at https://doc.turris.cz/doc/_media/rtrom01-schema.pdf
Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Tested-by: Rosen Penev <rosenp@gmail.com>
Commit eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL"), but
one needs an initramfs image to flash OpenWrt from stock firmware (as
described in the commit log). This patch has the initramfs image built
by default.
Thanks to blogic (for pointing to the FEATURES declaration in the target
Makefiles) and Musashino on the forum for suggesting
config/Config-images.in needed editing too. While at it, reorder the
TARGET_INITRAMFS_COMPRESSION_LZMA declarations alphabetically.
This patch will result in initramfs images for all lantiq subtargets
that have the ramdisk flag set. I tested on the falcon and ase
subtargets, which lack that flag, to confirm they don't produce any
initramfs images with this patch - which they do not.
Given the limited scope of the lantiq (sub)target(s), blogic indicated
this should be OK.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[fixed the wrong reference to eae6cac6a3 commit]
OpenWrt is completely compiled from sources using a 64 bit compiler, we
do not need support for the old 32 bit MIPS interface on 64 Bit CPUs,
deactivate it.
Fixes: 46af22de16 ("kernel: Remove CONFIG_COMPAT")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenWrt is completely compiled from sources using a 64 bit compiler, we
do not need support for the old 32 bit MIPS interface on 64 Bit CPUs,
deactivate it.
Fixes: 46af22de16 ("kernel: Remove CONFIG_COMPAT")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This moves some new configuration options to the generic kernel
configuration instead of configuring them for each target on our own.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes the following compilation issue that was introduced with the bump
to 4.14.118:
CC drivers/gpio/gpiolib-of.o
drivers/gpio/gpiolib-of.c: In function 'of_gpiochip_add':
drivers/gpio/gpiolib-of.c:510:12: error: too few arguments to function 'of_gpiochip_scan_gpios'
status = of_gpiochip_scan_gpios(chip);
^~~~~~~~~~~~~~~~~~~~~~
drivers/gpio/gpiolib-of.c:247:5: note: declared here
int of_gpiochip_scan_gpios(struct gpio_chip *chip, unsigned int start,
^~~~~~~~~~~~~~~~~~~~~~
scripts/Makefile.build:326: recipe for target 'drivers/gpio/gpiolib-of.o' failed
Fixes: 09050b6fe2 ("kernel: bump 4.14 to 4.14.118")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This target got bumped to 4.14 a long time ago
in commit: 2308b87204
Remove all leftover 4.9 files.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
CONFIG_HW_RANDOM_OMAP is not set to any value after kmod-random-omap was
removed, add the configuration option to the generic configuration.
Fixes: cd3b298533 ("omap24xx: Remove unmaintained target")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for different iterations of ESPRESSObin.
The added variants are:
ESPRESSObin with soldered eMMC,
ESPRESSObin V7, compared to V5 some passive elements changed and ethernet
ports labels positions have been reversed,
ESPRESSObin V7 with soldered eMMC.
Please refer to:
584d7c5 ("mvebu: new subtarget cortex A53")
for instruction how to boot OpenWrt image placed on SD card. It is
advised for owners of V5 and previous with bootloader based on U-Boot
2015.01, to upgrade the latest version available at:
http://espressobin.net/tech-spec.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Convert whole target to Device Tree based board detection instead of
identifying devices by dts file name. With this we can drop mvebu.sh
translation script and rely on common method for model detection.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Add vendors in device names and also rename few device names, for easier
identyfying potential firmware to flash. The vendor and device string is
mainly derived from model/compatipble string in dts from particular
device, but since not all devices are well described, some of the renames
follow marketing names.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Use make syntax to pass the U-Boot image location and boot with root
partitions size, instead of relying on shell functions and variables.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Drop overly complex amount of defines wich are referenced in the same
devices pool and move image recipes to common define, since devices not
using them overwrite it.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
All of U-Boot scripts repeat the same pattern with only Device Tree blob
name changing for respective device. Therefore create generic scripts
which will be altered on demad by image build process, and create
BOOT_SCRIPT variable which can be added to device recipe and will allow
referencing the same script by many device recipes. This will allow to
slim down the ammount of files in buildroot tree and avoid needlessly
incrementing amount of boot scripts if new devices will be added.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
All of arm64 devices have part of variables repeatedly defined. Stack
them to common define, and reference it in each device recipe.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Even if dts is not included in upstream Makefile, it is built anyway by
recipe specified in include/image.mk. Also remove Build/dtb, it's not
used since 3f72f3a ("mvebu: clearfog: include DTB for all variants in
image").
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This patch backports verbatim the commits from Linux 5.0 and 5.1
that implemented support for GigaDevice SPI NAND A and E variants.
Supported only in Linux 4.19 and later as based on the upstream
drivers/mtd/nand/spi/ framework.
mtd-spinand-add-support-for-GigaDevice-GD5FxGQ4xA.patch
commit c93c613214ac (5.0)
mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UExxG.patch
commit c40c7a990a46 (5.1)
Run-tested-on: GL.iNet AR750S
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
This activates "Supervisor Mode Access Prevention". modern CPUs will
prevent the kernel code from accessing any data from the userspace
without the usage of copy_to_user() or copy_from_user()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_BINFMT_MISC allows it to add support for new executable formats
to the kernel from user space, the kernel will then detect for example a
java binary and call the java execution program automatically. I am not
aware that this feature is used in OpenWrt and this could be used to
exploit something. Deactivate it for all targets for now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some targets deactivated CONFIG_SYN_COOKIES, for unknown reasons, use
the default setting from the generic configuration which activates
CONFIG_SYN_COOKIES.
This should prevent SYN flooding.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This removes support for executing old 32 bit applications on 64 bit ARM
and MIPS kernels.
On OpenWrt we normally compile all the user space applications on our
own and do not support third party binary only modules especial not 32
bit applications on 64 bit CPUs.
This reduces the attack surface on such systems and should also save
some memory.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These were renamed to CONFIG_STRICT_KERNEL_RWX and CONFIG_STRICT_MODULE_RWX and are
activated in kernel 4.14 and later by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates "Emulate Privileged Access Never using TTBR0_EL1
switching" on ARM64.
This should prevent the kernel from reading code from user space in
kernel context.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds additional checks to the copy_from_user() and copy_to_user()
functions. The details are described in this article:
https://lwn.net/Articles/695991/
This should only have a very small performance impact on system calls
and should not affect routing performance.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add some read-only properties to protect partitions from
accidental changes.
Also fixed two whitespaces error on the way.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The factory firmware omits the JFFS2 end-marker while flashing via
web-interface. Add a 64k padding after the marker fixes this problem.
When the end-marker is not present, OpenWRT won't save the overlayfs
after initial flash.
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
The correct board_name for the Turris Omnia is armada-385-turris-omnia.
Fixes: 4e8345ff68 ("mvebu: base-files: autodetect upgrade device")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Recently, upgrade device autodetection has been added to the mvebu target.
This exposes some shortcomings of the generic export_bootdevice function,
e.g. on the Turris Omnia: export_bootdevice silently reports the root
partition to be the boot device. This makes the sysupgrade process fail at
several places.
Fix this by clearly distinguishing between /proc/cmdline arguments which
specify the boot disk, and those which specify the root partition. Only in
the latter case, strip off the partition, and do it consistently.
root=PARTUUID=<pseudo PARTUUID for MBR> (any partition) and root=/dev/*
(any partition) are accepted.
The root of the problem is that the *existing* export_bootdevice in
/lib/upgrade/common.sh behaves differently, if the kernel is booted with
root=/dev/..., or if it is booted with root=PARTUUID=...
In the former case, it reports back major/minor of the root partition,
in the latter case it reports back major/minor of the complete boot disk.
Targets, which boot with root=/dev/... *and* use export_bootdevice /
export_partdevice, have added workarounds to this behaviour, by specifying
*negative* increments to the export_partdevice function.
Consequently, those targets have to be adapted to use positive increments,
otherwise they are broken by the change to export_bootdevice.
Fixes: 4e8345ff68 ("mvebu: base-files: autodetect upgrade device")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Extended mksenaofw to support new "capwap" header structure.
This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5
firmware.
Note that the factory image format changes for 3.1 and later firmware,
and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the
factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware
will refuse the factory_35.bin file.
Flashing from the Engenius 3.1.0 firmware with the factory_35.bin
firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW")
is only intended as part of the upgrade path to 3.5.5 firmware.
Modified ipq40xx image Makefile to appropriately invoke mksenaofw
with new parameters to configure the capwap header.
Note that there is currently no method to return to factory firmware,
so this is a one-way street.
Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is
to navigate to 192.168.1.1 on the stock firmware and navigate to the
firmware menu. Then copy the URL you have for that page, something like
http://192.168.1.1/cgi-bin/luci/;stok=12345abcdef/admin/system/flashops
and replace the trailing /admin/system/flashops with just /easyflashops
You should then be presented with a simple "Firmware Upgrade" page.
On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox.
Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin,
click "Upgrade" and on the following page select "Proceed".
Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to
use the stock firmware update menu. Choose the
openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click
"Upload" and "Proceed".
The device should then flash the OpenWrt firmware and reboot. Note
that this resets the device to a default configuration with Wi-Fi
disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2
acting as a LAN port with a DHCP server on 192.168.1.x (AP is at
192.168.1.1)
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[sorry, for unfixing the 80-lines eyesores.]
This patch works around an issue where reboot would cause the AP
to power down and not reboot.
The ipq4019 restart controller reboot causes the system
to power down and not recover. Fix is to disable the restart
controller in the device tree and the device reverts to
using the watchdog to perform the reset.
The real problem is due to the buggy bootloader that ships
with the device. Steve Glennon reported in the PR for this
patch: <https://github.com/openwrt/openwrt/pull/2009> that:
"the problem was due to a bad u-boot that ships with the device.
Using the u-boot that comes with 3.5.5.3 EnGenius factory
software now allows the old code (using the do_msm_reboot)
to reboot successfully.
On to the bad news:
Well 3.5.5.3 is a bad path. Finally managed to recover. You
CANNOT use prior EnGenius firmware to downgrade.
Findings:
* They now password protect the serial console with a new, unkown
password.
* They changed the protection on their walled-garden. I have to
use the ssh admin@ip /bin/sh --login to get out of their
walled-garden.
* Attempts to flash the original 3.0.0 or 3.0.1 EnGenius firmware
fail through the UI and sysupgrade. Their firmware update GUI now
seem to detect regular openwrt images, but they fail to flash
Attempts to flash a normal OpenWrt image with sysupgrade fail.
[..]
Attempts to sysupgrade with EnGenius firmware fail with the same
"mandatory section(s) missing" error, so you cannot downgrade to
3.0.0 or 3.0.1."
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added valuable
findings from github discussion]
Marvell sata controllers in all kirkwood SoCs support
sata port multipliers, just like mvebu.
Enable this feature in the default kernel config
so it is available in normal builds.
tested and working on nsa310b
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Luis Araneda